Example: tourism industry
CMU CAD Details
12 brick with brick ties rer 7 manufacturer's srecificatioins. 8 9 13. 1/2" x 15" anchor bolts, 6'-0")13) oc., 12" from corners. 14. flashing with weer holes @ 12 20 19 48" o.c. 15. fiinished grade. 15 16. (4) #4 rebars all in solid footing 3" off bottom. 17. tyrical 4" concrete rost, 4'-0" o.c. uxider cj load-beariing walls. 18. comracted ...
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Plumbing CAD Details
autocaddetails.netA. 3" Plumbing vent 6" above roof and 10" ~ from corner 3" Sanitary Cross or Double sanilarytee ~ ... AS STANDARD WITH MFG UPPER HANGER STANDARD WITH FIXTURE FURNISHED ELLULAR MASONRYWALL BACKUP BRACKETS, SEE DETAIL (~~-"'PECHASE ... Plumbing CAD Details …
Deck CAD Details
autocaddetails.net®LEDGER Post/Beam Connector Pier Block on undisturbed soil gravel orfooting 4" x Timber-Beams... See Detail "C" or-I4-"D" for PostConnections Double Joist orStringer Beam
Mechanical CAD Details
autocaddetails.netgate valve strainer with blowdown concentric reducer (typical) elbow support floor grout floor flange 1/4" gate valve flow control-balancingvalve vibration isolator (typical)
Civil Engineering CAD Details
autocaddetails.netEXISTING GROUND/ FINISH GRADE 0" 6"-3/4"CRUSHED ROCK "0 3/4" CURB STOP MANUAL AIR-RELEASE ASSEMBLY 3/4" CORPORATION WATER MAIN Samples from www.AutoCADDetails.net
Stairs and Steps CAD Details
autocaddetails.nete handrail at 5'-0"o.c. ls sections ovable socket l. 3/8 x 8 x pl. w/2 hors d bottom /i-; 1 1/2" std. pip ~ 4"xcont. 0 wi verticals ove flooring max. handrai co i shall be rem m ping over conc. plank 1.4 x w1.4 i ~ floor, i" el. xx'-xx" ~--u,----; 2"x 8" lg. pipe ~ welded to p ~ 0'-8".anchor 1 1/2" 3/4" exp. anc clear--; 1 - #4top an ~ cont ...
Fireplaces CAD Details
autocaddetails.netdamper specifications steel dampers fireplace width steel dampers (inches) a b c d e 24 -26 28.25 26.75 13 24 9.5 27 -30 32.25 30.75 13 28 9.5 31 -34 36.25 34.75 13 ...
Related documents
530.1-02 Specification for Masonry Structures
freiburgerconsulting.comMasonry construction and materials shall conform to all requirements of "Specification for Masonry Structures (ACI 530.1/ASCE 6/TMS 602)," published by The ... 2.4 E Stainless steel Specify when stainless steel joint reinforcement, anchors, ties, and/or accessories are required.
MIW Pocket Guide - Masonry Institute of Washington
www.masonryinstitute.comE 754: Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints Pavers C 410: Specification for Industrial Floor Brick C 902: Specification for Pedestrian and Light Traffic Paving Brick C 936: Specification for Solid Concrete Interlocking Paving Units 12.
W FlooR Foundations - APAwood.org
www.apawood.orgsuch as those supporting exterior shear walls, the masonry piers must be designed accordingly, typically reinforced with vertical steel rods (rebar) and concrete fill. Anchors or straps to resist uplift are “wet-set” into the piers, secured by the concrete fill. The specification of masonry piers provides for precise
Building Code Requirements for Masonry Structures
cdnassets.hw.netNov 28, 2012 · structural adequacy of masonry construction requires that the compressive strength of masonry equals or exceeds the specified strength. Masonry design by prescriptive approaches relies on rules and masonry compressive strength need not be verified. 1.2.4 The contract documents shall be consistent with design assumptions.