COMPLETE LAB MANUAL FOR CCNP

1 Page 1 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. CCNP CISCO CERTIFIED NETWORK PROFESSIONAL LAB MANUAL VER Page 2 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. ACKNOWLEDGEMENT We can write a 1000 page book, but we can t find enough words to describe the credit Mr. Siddiq Ahmed deserves for what is good about this book. Your ability to guide us made the toughest things easy in developing this book. We still refuse to write a book unless you develop it!! Behind the scenes at Netmetrics is a vast array of talented people all of whom made it possible to develop the book. People, who provided the right equipment in the right time, people who maintained a friendly atmosphere to finish the work in time.

2 Many thanks to you all for the hard and good work. Thanks to Nizam, Anwar, Afsar, Awadh, Sreenivas and Mr. Prasad for finding better ways to describe how the technical pieces fit together, for fixing errors. Thanks to Mr. Abdur Rahman for giving us the time we needed to work on this book and by making sure the job was fun. Finally, no acknowledgement section could be COMPLETE without acknowledging ourselves, who took all the responsibility and dedication in completing the book. Finally, to GOD, who gives us strength when things are tough, and peace beyond belief THANK YOU!!! Page 3 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. PAPER 1 Routing BUILDING SCALABLE CISCO INTERNETWORKS BSCI (642 901) Page 4 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved.

3 Module 1 eigrp Page 5 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. eigrp LABS INDEX 1. CONFIGURING BASIC eigrp 2. CONFIGURING IP DEFAULT-NETWORK COMMAND 3. CONFIGURE ROUTE SUMMARIZATION 4. LOAD BALANCING ACROSS EQUAL COST PATH 5. LOAD BALANCING ACROSS UNEQUAL COST PATH 6. CONFIGURE eigrp AUTHENTICATION (MD5) 7. CONFIGURE eigrp STUB 8. eigrp REDISTRIBUTION WITH RIPv2 9. eigrp REDISTRIBUTION WITH OSPF 10. CONFIGURE eigrp WITH REDISTRIBUTE CONNECTED. 11. CONFIGURE eigrp AND IGRP Page 6 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. Interface IP Address Configuration R1 Interface IP Address Subnet Mask S 0/2/0 E 0 R2 Interface IP Address Subnet Mask S 0 E 0 Lab Objective: Task 1 Configure eigrp on 2 routers in AS 100.

4 Disable Auto-summary. R1 Router eigrp 100 Network Network No auto-summary R2 Router eigrp 100 Network Network No auto-summary Verification : Lab 1 Basic eigrp Configuration R2 R1 S 0/2/0 S 0 E 0 E 0 Page 7 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. R1#show ip route C is directly connected, Serial0/2/0 D [90/2195456] via , 00:43:52, Serial0/2/0 C is directly connected, FastEthernet0/0 R1#show ip eigrp neighbors IP- eigrp neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 Se0/2/0 13 00:45:08 355 2130 0 106 Page 8 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved.

5 Interface IP Address Configuration R1 Interface IP Address Subnet Mask S 1 E 0 R2 Interface IP Address Subnet Mask S 1 S0 E 0 R3 Interface IP Address Subnet Mask S 0/2 E 0 Lab Objective: Lab 9 IP RIP Triggered Lab 2 Configuring ip default-network Command R2 R1 S0 S1 E 0 E 0 R3 E 0 S0 S0/2 Page 9 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. Task 1 Configure eigrp according to the above scenario. Configure R1 ( S0, E0 ), R2 ( S1, S0, E0 ) in eigrp AS 100 and R3 ( S0/2 ) in eigrp AS 200. Do not advertise network in eigrp process. R1 wants to send packets to network Use the Ip default-network command to accomplish this task. Also disable auto-summary. R1 Router eigrp 100 Network Network No auto-summary R2 Router eigrp 100 Network Network Network No auto-summary Ip route Ip default-network R3 Router eigrp 100 Network No auto-summary.

6 Verification : R1#show ip route Gateway of last resort is to network C is directly connected, Serial0/2/0 D* [90/2681856] via , 00:00:14, Serial0/2/0 D [90/2195456] via , 00:04:43, Serial0/2/0 C is directly connected, FastEthernet0/0 The output displays network as a D* route in the routing table as this is candidate default-route established in R1 to reach network Note: When we ping from R1 to network R1 # ping Result: 100% success Page 10 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. Interface IP Address Configuration R1 Interface IP Address Subnet Mask S 0/2/0 E 0 R2 Interface IP Address Subnet Mask S 1 S0 E 0 R3 Interface IP Address Subnet Mask S 0/2 E 0 Loopback 1 Loopback 2 Loopback 3 Loopback 4 Loopback 5 Loopback 6 Loopback 7 Loopback 8 Lab Objective: Task 1 Lab 3 Route Summarization with eigrp R2 R1 S0/2/0 S1 E 0 Loopback 1-8 R3 E 0 S0 S0/2 E 0 Page 11 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved.

7 Configure the following Loopback Interfaces on R3 and advertise them under eigrp : Loopback 1: Loopback 2: Loopback 3: Loopback 4: Loopback 5: Loopback 6: Loopback 7: Loopback 8: R3 Interface loopback 1 Ip address Interface loopback 2 Ip address Interface loopback 3 Ip address Interface loopback 4 Ip address Interface loopback 5 Ip address Interface loopback 6 Ip address Interface loopback 7 Ip address Interface loopback 8 Ip address Router eigrp 100 Network Network Network Network Network Network Network Network Network No auto-summary Task 2 Page 12 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. Configure eigrp on R1 and R2. Advertise the directly connected networks in eigrp in AS 100.

8 Disable auto-summary. Also configure route summarization so that only one summary route is advertised to R1. R1 Router eigrp 100 Network Network No auto-summary R2 Router eigrp 100 Network Network Network No auto-summary Int s0 Ip summary-address eigrp 100 Verification: R1#show ip route C is directly connected, Serial0/2/0 D [90/2681856] via , 00:00:02, Serial0/2/0 D [90/2195456] via , 00:00:02, Serial0/2/0 is subnetted, 1 subnets D [90/2809856] via , 00:00:02, Serial0/2/0 C is directly connected, FastEthernet0/0 D [90/2707456] via , 00:00:02, Serial0/2/0 With route summarization on R2 a summary route is created pointing to null 0 R2#show ip route C is directly connected, Serial0 C is directly connected, Serial1 C is directly connected, Ethernet0 is variably subnetted, 9 subnets, 2 masks D [90/2297856] via , 00:07.

9 13, Serial1 D [90/2297856] via , 00:07:08, Serial1 D [90/2297856] via , 00:07:04, Serial1 D [90/2297856] via , 00:06:56, Serial1 D [90/2297856] via , 00:06:49, Serial1 D is a summary, 00:01:24, Null0 D [90/2297856] via , 00:07:33, Serial1 D [90/2297856] via , 00:07:25, Serial1 D [90/2297856] via , 00:07:18, Serial1 D [90/2172416] via , 00:01:30, Serial0 D [90/2195456] via , 00:08:03, Serial1 Page 13 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. Interface IP Address Configuration R2 Interface IP Address Subnet Mask S 0 S 1 E 0 R3 Interface IP Address Subnet Mask S 1 S0 E 0 Lab Objective: Task 1 Configure eigrp AS 100 as per the above scenario and verify load balancing using the traceroute command on R3 : R2 Router eigrp 100 Network R3 Router eigrp 100 Network Lab 4 Load balancing across Equal Cost Path R2 R1 S 0 S 0 E 0 E 0 S 1 S 1 Page 14 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved.

10 Network Network No auto-summary Network Network No auto-summary Verification: R3#show ip route C is directly connected, Serial1 C is directly connected, Serial0 D [90/2195456] via , 00:07:42, Serial1 [90/2195456] via , 00:07:42, Serial0 C is directly connected, Ethernet0 First Traceroute packet going via R3#traceroute Type escape sequence to abort. Tracing the route to 1 32 msec 20 msec * Second Traceroute packet going via R3#traceroute Type escape sequence to abort. Tracing the route to 1 20 msec 28 msec * Page 15 of 315 NETMETRIC-SOLUTIONS All contents are copyright @ 2007-2010 All rights reserved. (Scenario Based On Lab 4) Interface IP Address Configuration R2 Interface IP Address Subnet Mask S 0 S 1 E 0 R3 Interface IP Address Subnet Mask S 1 S0 E 0 Lab Objective: Task 1 Configure eigrp AS 100 as per the above scenario.