DESIGN, OPERATION & MAINTENANCE MANUAL

1 Pyrogen (Australia) Pty. Ltd. Box 694 Hurstville 1481 Suite 2, 9 Gloucester Road Hurstville NSW 2220 AustraliaTel: 61 2 9586 3200 Fax: 61 2 9586 3211 E-mail: Website: MANUAL : DOM 00/07 Issued; July, 2000 Revision No.: INDUSTRIAL FIXED AEROSOL FIRE SUPPRESSION SYSTEMDESIGN, OPERATION & MAINTENANCEMANUALJuly 2000 This MANUAL is issued by Pyrogen (Australia) Pty. Ltd. and is for use by trained and authorisedpersonnel only.

2 Unauthorised copying of this MANUAL and its contents and use by unauthorisedpersonnel is strictly forbidden and may lead to legal action against those who do document is accurate at time of issue and Pyrogen reserves the right to make changes to itscontent from time to (Australia) Pty. MANUAL : DOM 00/07 (i) Issued: July, 2000 Revision No.: Revision Control ScheduleDoc. final internal Issue to LPCB (1) Office Address Change & & Safety Areas Calcs.

3 Modified as per B Gen. Selection Chart as per request information on thermal initiating drawings & other minor changesJB/AMPACP yrogen (Australia) Pty. MANUAL : DOM 00/07 (ii) Issued: July, 2000 Revision No.: MANUAL is intended for use with Pyrogen Industrial Fire Suppression Systems. Thesystems are designed as fixed systems for unoccupied and normally unoccupied systems for total flooding applications shall comply with the requirements of thefollowing Standards:- AS/NZS 4487:1997 Australia/New Zealand Standard Pyrogen Fire Extinguishing Systems.

4 And- AS/NZS :1997 Australia/New Zealand Standard MAINTENANCE of Fire Protection Equipment Part 16: Pyrogen Fire Extinguishing Aerosol SystemsFor the protection of a specified risk area a specific advice and approval may berequired from an appropriate Approval who design, operate, own and maintain these systems should read the entireManual. Specific sections would be of particular interest depending on one sresponsibility. If there should be any questions regarding this MANUAL , please contactour representatives from a Pyrogen office below or contact the nearest PyrogenAuthorised required persons who install and commission Pyrogen systems must beapproved by the Appropriate Authorities.

5 System Design Approval Certificates must becompleted and sent to a Pyrogen office for endorsement prior to supply and installationof a Pyrogen Fire Suppression companies may also be required to supply details to the Approval Authorityprior to each installation and provide a Commissioning Certificate upon completion ofthe installation in the specified risk Pyrogen Fire Suppression System requires minimal MAINTENANCE , mainlysupervision of electrical circuitry, however the system should be inspected at regularintervals to provide maximum assurance that your fire suppression system will operateeffectively and safely.

6 Inspection and MAINTENANCE should be conducted in accordancewith the inspection and MAINTENANCE schedule included in this MANUAL is limited for use with Pyrogen Industrial Fire Suppression Systems andwithin the requirements and limitations detailed within this (Australia) Pty. MANUAL : DOM 00/07 (iii) Issued: July, 2000 Revision No.: can be directed to Pyrogen personnel in the following Pyrogen offices:Australian Office:PYROGEN (AUSTRALIA) PTY.

7 2, Ground Floor,9 Gloucester Rd.,Hurstville NSW 2220, : +(61-2) 9586-3200 Fax: +(61-2) 9586-3211 Email: Headquarters:PYROGEN CORPORATION SDN. 40-1, Jalan PJS 5/2,Taman Desaria,46000 Petaling Jaya,Selangor Darul Ehsan, : +(60-3) 787-64688 Fax: +(60-3) 787-54688 Email: Office:PYROGEN Mill Business Centre,Spa Road, Bolton,BL1 4 LFUKTel.: +(44) 1204 373300 Fax: +(44) 1204 373355 Email: (Australia) Pty. MANUAL : DOM 00/07 (iv) Issued: July, 2000 Revision No.

8 : OF CONTENTSFOREWORD ..IISECTION 1. GENERAL .. Terminology .. PyroGen Product Standards/Testing .. What is PyroGen?.. PyroGen Chemical Identity .. PyroGen Extinguishing Action .. PyroGen and Competitive PyroGen Applications and Limitations .. PyroGen Safety Data .. PyroGen Environmental Characteristics .. PyroGen Technical 16 SECTION 2. SYSTEM DESIGN FOR TOTAL FLOODING General .. Design Methodology .. Design Design Quantity .. Number of MAG generators .. PyroGen Range.

9 Minimum Holding Time .. Enclosure Design Quantity Calculations - Special Design Limitations .. PyroGen 16 SECTION 3. SYSTEM DESIGN FOR LOCAL PyroGen Packaged Systems.. 1 SECTION 4. SYSTEM Electrical automatic Electrical MANUAL OPERATION .. Thermal automatic OPERATION .. System isolate Operating devices .. Detection, alarm and control systems, indicating equipment, warning devices .. Post-fire procedure .. 2 SECTION 5. SYSTEM COMPONENTS .. 5-0 SECTION 6. SYSTEM INSTALLATION.

10 Prior to installation .. Incorporation of Thermal Initiating Spacing and Location .. Mounting Methods .. Electric Connection of Thermal Initiating Device .. 8 Pyrogen (Australia) Pty. MANUAL : DOM 00/07 (v) Issued: July, 2000 Revision No.: 7. SYSTEM PyroGen Installation and Expiry Date Label .. PyroGen Warning & Instruction Signs .. 1 SECTION 8. SYSTEM COMMISSIONING .. 8-0 SECTION 9. SYSTEM 9-0 SECTION 10. SAFETY MEASURES.