Example: quiz answers
DIRECT VENT FURNACES - Williams
5 ½ʺ Insulated, galvanized sheet for all direct-vent units.from finished floor - 22,000 and 30,000 BTU/hr. models. 24ʺ from top of appliance to ceiling or other obstructions 12ʺ VENT EXTENSIONSclearance for curtains 24ʺ Maximum wall thickness. 30ʺ 14,000 BTU/hr. models. from top of appliance to
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Installation, Operating & Maintenance Instructions
www.williamscomfortprod.com4 covered by the warranty. Williams’ fan coil units are suitable for zero clearance to combustible material. Start-Up After the fan coil and piping have been installed, pressure test for 24 hours with a minimum of
Owner’s Manual
www.williamscomfortprod.com1. The heating equipment must be installed by a qualified installer and operated in accordance with the installation and homeowner’s instructions furnished with the equipment. 2. Any travel, diagnostic costs, service labor, and labor to repair the defective unit will …
VENTED ROOM HEATERS - Williams
www.williamscomfortprod.com• Automatic temperature and safety controls • Resettable vent-limit safety switch 20,000 BTU/hr. 35,000 - 65,000 BTU/hr. ENCLOSED COMPACT MODEL FOR SMALLER ROOMS. ... • Venting must comply with the “Venting and Chimney Requirements” section of the instruction manual.
Direct Vent Furnaces IOM - Williams
www.williamscomfortprod.com8. Install the furnace vent directly to the outdoors so that harmful combustible flue gases will not collect inside the building. Follow the venting instructions for your type of installation exactly. Use only the type and size of vent pipe and fittings specified. 9. BE SURE to provide for adequate combustion and ventilation air.
TOP VENT GAS WALL HEATER - williamscomfortprod.com
www.williamscomfortprod.comof vent pipe and fittings specified. 10. BE SURE to provide for adequate combustion and ventilation air. The flow of this air to the furnace must not be blocked. 11. NEVER vent flue gases into another room, a fireplace or any space inside a building. This could cause property damage, bodily injury or death. 12.
Related documents
Hot dip galvanized coatings on fabricated iron and steel ...
www.galvanizeit.coma) sheet, wire and woven or welded mesh products that are continuously hot dip galvanized; b) tube and pipe that are hot dip galvanized in automatic plants; c) hot dip galvanized products (e.g. fasteners) for which specific standards exist and which might include
Standard Specification for Steel Sheet, Zinc-Coated ...
www.tjxysteel.com3.2.2 differentially coated, n—galvanized steel sheet having a specified “coating designation” on one surface and a signifi-cantly lighter specified “coating designation” on the other surface. 3.2.2.1 Discussion—The single side relationship of either specified “coating designation” is the same as shown in the
781 - Bradley Corp
www.bradleycorp.comBACK: galvanized steel. MIRROR: first quality ¼" float glass, thermosetting infrared cured paint backing with Poly-Glaze protective finish. Manufactured in accordance with ASTM C 1036 and ASTM C 1503. All edges protected by shock-absorbing, neoprene tubing. The back of the mirror is protected by a sheet of ¼"
STANDARD SERIES Badger 1 - InSinkErator
insinkerator.emerson.com• Rugged Galvanized Steel Construction (For Disposer Durability) • Space-Saving Compact Design • Available with or without a factory installed power cord. SubmittalSheet Job Specifications Specifications Sample Specification The complete InSinkErator warranty is included in the Care & Use Booklet packed with each uni.t * 1-800-558-5700
TECHNICAL DATA SHEET - Henry
henry.comcast-in-place concrete, concrete block, steel, aluminum and galvanized metal. Strike masonry joints full-flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions. Concrete must be cured a minimum of 14 days. Curing
Sheet Metal Thickness (Gauge) Chart in Inches
davidsonsales.comJul 19, 2007 · Sheet Metal Thickness (Gauge) Chart in Inches Gauge Mild Steel Aluminum Galvanized Steel Stainless Steel 3 0.2391 0.2294 0.2500 4 0.2242 0.2043 0.2344 5 0.2092 0.1819 0.2187 6 0.1943 0.1620 0.2031 7 0.1793 0.1443 0.1875 8 0.1644 0.1285 0.1680 0.1719 9 0.1495 0.1144 0.1532 0.1562
Wall Mounted Propeller Fans - PennBarry
www.pennbarry.comgalvanized panel. • Available in sizes 24” to 48”. Model: BHH-Series • Static pressure up to 1 in. wg. • Flow capacity up to 58,400 CFM. • Exhaust or supply in heavy-duty applications. • High-efficiency fabricated steel propeller, a robust galvanized and a fully developed venturi integrally spun into a galvanized panel.
SHEET METAL CATALOG - Excelsior
www.excelsiorhvac.com7 Snap-Lock Technology Galvanized Pipe, Round and Oval 14" Pipe 16" Pipe 18" Pipe 20" Pipe 24" Pipe 12" Pipe 10" Pipe 9" Pipe Length Gauge Item# 2' 24 140209
Standard Steel Pipe - Wheatland
www.wheatland.comHot-dip Galvanized The average weight of zinc coating shall be not less than 1.8 oz. per sq. ft. of surface (inside and outside). When galvanized pipe is bent or otherwise fabricated to a degree which causes zinc coating to stretch or compress beyond the limit of elasticity, some flaking of the coating may occur.