Example: tourism industry
ELECTRIC MOTORS IEC IE3 Motor Range - Rotec …
BASIC DIMENSIONS B5 - flange (“D” flange) B3 - foot mounted motor The flange is bigger than the motor frame. The holes are not tapped. B5 flanges are available for …
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
squirrel-cage induction motors - Motors & Gears: …
www.rotor.besquirrel-cage induction motors type 5RN type 5RN rotor b.v., mors 2, p.o.box 45, 7150 AA eibergen,The Netherlands, phone +31 (0)545 46 46 40, fax +31 (0)545 47 50 65
Worldwide Sale and Service Network - Motors & …
www.rotor.be63 ... 200 140 ... 360 Kegelstirnradgetriebe und Kegelstirnrad-getriebemotoren Right angle shaft gear reducers and gear-motors * *
squirrel-cage induction motors - Motors & Gears: …
www.rotor.besquirrel-cage induction motors type 5RN type 5RN frame sizes 56 to 90 outputs (S1-50 Hz) 0.12 to 2,2 kW 2-pole, 3000 min-1 0.09 to 2.2 kW 4-pole, 1500 min-1 0.06 to 1.1 kW 6-pole, 1000 min-1
squirrel-cage induction motors - Motors & Gears: …
www.rotor.besquirrel-cage induction motors type 4AP type 4AP frame sizes 112 to 132 outputs (S1-50 Hz) 4 to 11 kW 2-pole, 3000 min-1 4 to 10 kW 4-pole, 1500 min-1 2.2 to 5.5 kW 6-pole, 1000 min-1 1.5 to 4 kW
Elektromotoren - Rotec Belgium
www.rotor.beGeen motor zonder Rotor! Dit is de slogan waar we al sinds jaar en dag de markt mee bedienen. De catalogus rotor nl ® elektromotoren is bedoeld als handzaam naslagwerk voor zowel de machinebouwer (OEMer) als gebruiker van elektromotoren. We hebben in deze catalogus onderscheidt gemaakt in vijf hoofdstukken namelijk:
moteurs électriques rotor nl ères
www.rotor.beAC AA LC GC L W Z B1 K DA HA M S 45 22,5 LD GA F TLA P N D DA H 2 page chapitre 1 sous réserve de modification édition première Oct. 2001 moteurs électriques rotor nl®
mountings - rotor.be
www.rotor.beim 1001 im b3 im 1011 im v5 im 1031 im 1051 im 1061 im 1071 im 2071 im 2061 im 2051 im 2031 im 2011 im 2001 2 m 1i 01 im 3031 im 3011 im 3006 3 m 1i 01 im 3611 im ...
Certificates: Atex, IECEx, CUTR and more - rotor.be
www.rotor.bedevelopment and improvement, the company reserves the right to supply products which may differ slightly from those illustrated and described in this publication.
Related documents
Flange Insul Kits
www.calpicoinc.comFLANGE INSULATION C A L P I C O KITS FOR WATER, NATURAL GAS, PETROLEUM AND OTHER PIPE LINES. Flange sizes 1/2" thru …
JetTech Help Intro - iwt.com.au
www.iwt.com.auFlange fixing Note : that with the female clamp fixing and the flange connection, as you can see in figure 5 and 6, there is also the need to provide both effective heat insulation and a perfect airtight seal. fig. 6 2.5 Air intakes Different air intake arrangements are possible for …
Roof Flashing Details Index - fieldscorp.com
fieldscorp.comstaggered. Flange adhered into M300 RubrMastic & primed with M400 RubrPrime before installing M60 RubrPoly flashing sheets Fields roof membrane sheets Coverboard insulation Thermal insulation Roof deck Roof deck M60 RubrPoly envelope sheet M60 RubrPoly sheet extended below blocking Sheet metal scupper A .75” x 3” min “L” shaped gravel guard
Technical Information Proline Promag 10W
portal.endress.com2 Core insulation d l e i h s e r o 3C 4 Core jacket 5 Core reinforcement 6 Cable shield 7 Outer jacket Operation in zones of severe electrical interference ... Both sensor flanges are connected to the pipe flange by means of a ground cable (copper wire, at least 6 mm² / 0.0093 in²) and grounded. Connect the transmitter or sensor connection
Flange Insulation Sets - KLINGER Australia
www.klinger.com.auThe PGE insulation set uses a machined, glass -reinforced epoxy (GRE) resin with an o-ring or spring energised seal. PGE can be used for flange …
Pipe Insulation (Hot & Cold) Material Selection & Application
local.ecollege.iePipe Insulation (Hot & Cold) Material Selection & Application Revision 2.0, August 2014 C. High Temperature Thermal Insulation (1). 315°C through 815°C - i.e. Turbines, breechings, stacks, exhausts, incinerators. 1.2 Insulation Types Insulation materials are …
Recommended Torque Values - Central Plastics
www.centralplastics.comRecommended Torque Values ANSI 150# Flanges ANSI 300# Flanges ANSI 400# Flanges Size Qty. Bolt Dia. Suggested Size Qty. …
fwb Tech & Download Content www.fwb.co.uk …
www.fwb.co.uk3 Flange Tables, Bolt Sizing and Gasket Materials There are many different standards relating to the sizing and specification of flange & bolt sets world-wide, common ones include ASA / ANSI / ASME (USA), PN /
Insulation & Ventilation - bluebaybp.co.uk
www.bluebaybp.co.ukInsulation & Ventilation 196 Sales: 0845 450 9766 www.bluebaybp.co.uk Solcoure Peri-Break is designed to enhance the thermal performance of a structure at the junction between the ground fl oor and external cavity wall by reducing the thermal linear bridging at …
FLANGE BOLTING GUIDE - Valvtronic
www.valvtronic.comA Division of Bray International, Inc. The Ultimate Critical Service Triple Offset Valve Flange Bolting Guide All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.