ET 200SP distributed I/O system - EandM

1 ET 200SP distributed I/O system _____ SIMATIC ET 200SP ET 200SP distributed I/O system system Manual 03/2012 A5E03576849-01 Preface Guide to documentation 1 Product overview 2 Application planning 3 Installation 4 Connecting 5 Configuring 6 Commissioning 7 Maintenance 8 Technical specifications 9 Dimension drawings A Accessories/spare parts B Calculating the electrical resistance C Service & Support D Legal information Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken.

2 WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. NOTICE indicates that an unintended result or situation can occur if the relevant information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/ system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

3 Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

4 Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Industry Sector Postfach 48 48 90026 N RNBERG GERMANY A5E03576849-01 03/2012 Technical data subject to change Copyright Siemens AG 2012. All rights reserved ET 200SP distributed I/O system system Manual, 03/2012, A5E03576849-01 3 Preface Purpose of the documentation This documentation provides important information on configuring, installing, wiring and commissioning the ET 200SP distributed I/O system . Basic knowledge required A basic knowledge of automation technology is required to understand the documentation. Conventions This documentation contains schematic diagrams of the devices described.

5 The diagrams may differ slightly from the devices supplied. Please observe notes labeled as follows: Note The notes contain important information on the product described in the documentation, on the handling of the product or on part of the documentation to which particular attention should be paid. Recycling and disposal The products can be recycled due to their low-pollutant content. For environmentally compliant recycling and disposal of your old device, please contact a company certified for the disposal of electronic waste. Additional support Information about the technical support available can be found in the appendix (Page 99) to this documentation. The range of technical support for the individual SIMATIC products and systems can be found on the Internet ( ). The online catalog and the ordering system are available on the Internet ( ). Preface ET 200SP distributed I/O system 4 system Manual, 03/2012, A5E03576849-01 ET 200SP distributed I/O system system Manual, 03/2012, A5E03576849-01 5 Table of contents 1 Guide to 2 Product distributed I/O - What is the ET 200SP distributed I/O system ?

6 15 Components of ET 200SP ..17 3 Application Selection of a suitable Digital or analog modules without temperature Analog modules with temperature Maximum Forming potential groups ..25 Configuration examples for potential 4 Inst allation ..29 Basic principles of Installing the interface Installing Installing the server 5 Connecting ..37 Rules and regulations for operating the ET Operating the ET 200SP on grounded incoming Electrical configuration of the ET Wiring Wiring Connecting cable Connecting supply voltage on the interface Conne cting profinet IO bus adapter BA 2xRJ45 to the interface Connecting profinet IO bus adapter BA 2xFC to the interface module (in preparation)..52 Installing I/O modules and BU Table of contents ET 200SP distributed I/O system 6 system Manual, 03/2012, A5E03576849-01 Labeling ET 200SP ..56 Factory Optional markings.

7 57 Applying color identification Applying labeling strips ..60 Applying reference identification 6 Configuring the ET 200SP ..63 7 Commissioning the ET 200 65 Startup of the ET Identification Resetting interface module to factory Resetting the interface module to factory settings via a RESET Resetting the interface module to factory settings via profinet Reassigning parameters during 8 Removing and inserting I/O Changing the type of an I/O Replacing the I/O Replacing the terminal box on the Firmware update ..80 9 Technical Standards and Electromagnetic Shipping and storage Mechanical and climatic ambient Information on insulation, protection class, degree of protection and rated voltage ..89 Use of the ET 200SP in zone 2 potentially explosive atmospheres ..90 A Dimension drawings ..91 Server Shield Labeling strip ..92 Reference identification Table of contents ET 200SP distributed I/O system system Manual, 03/2012, A5E03576849-01 7 B Accessories/spare parts.

8 95 C Calculating the electrical D Service & Table of contents ET 200SP distributed I/O system 8 system Manual, 03/2012, A5E03576849-01 ET 200SP distributed I/O system system Manual, 03/2012, A5E03576849-01 9 Guide to documentation 1 Introduction The ET 200SP distributed I/O system documentation has a modular structure. It consists of different documents which contain instructions, reference information or functional descriptions. The ET 200SP documentation includes the following documents: system manual ET 200SP Device manuals of the modules ( IM, I/O modules) Topic-orientated function manuals ( analog value processing) Furthermore, the information system in the STEP 7 online help offers you assistance in configuring and programming your ET 200SP system . Selecting the documentation using design versions A typical design version is represented below. You can read which documentation is necessary for the version in question in addition to this system manual.

9 Guide to documentation ET 200SP distributed I/O system 10 system Manual, 03/2012, A5E03576849-01 Documentation for the ET 200SP distributed I/O system with IM, BaseUnits, digital and analog modules ,0'4', $, $4%DVH8 QLWV Figure 1-1 Example of a system design Table 1- 1 Documentation for the ET 200SP distributed I/O system with interface module, I/O modules and server module Number Components Documentation Important contents IM Device manual Interface module ( ) DI Device manuals Digital input modules ( ) DQ Device manuals Digital output modules ( ) AI Device manuals Analog input modules ( ) AQ Device manual Analog output module ( ) Connecting Parameter assignment/addressing Interrupt, error and system messages Technical specifications Dimensional diagram AI/AQ ET 200SP product information ( ) Representation of analog values Server module Device manual Interface module ( ) See above Guide to documentation ET 200SP distributed I/O system system Manual, 03/2012, A5E03576849-01 11 Number Components Documentation Important contents BaseUnits Device manual BaseUnits ( ) Technical specifications Dimensional diagram profinet in STEP 7 V11 function manual profinet with STEP 7 V11 ( ) IM profinet in STEP 7 profinet system description ( ) system manual Programming manual From PROFIBUS DP to profinet IO ( ) profinet basics profinet functions profinet diagnostics Guide to documentation ET 200SP distributed I/O system 12 system Manual, 03/2012, A5E03576849-01 ET 200SP distributed I/O system system Manual, 03/2012, A5E03576849-01 13 Product overview distributed I/O - overview distributed I/O systems field of application A plant configuration quite often features a process I/O configuration in a central automation system .

10 When the inputs/outputs are far away from the automation system , wiring can become very extensive and complex. distributed I/O systems are the perfect solution for such plants: The CPU controller is located centrally. The I/O system (inputs and outputs) work locally on a distributed basis. What is profinet IO? profinet IO is an open transmission system with real-time functionality defined in accordance with the profinet standard. This standard defines a cross-manufacturer communication, automation and engineering model. Industrial-strength connections are available for wiring the profinet components. profinet discards the hierarchical PROFIBUS master/slave concept and deploys a provider/consumer principle instead. The IO devices that will be subscribed to by an IO controller are defined within the configuration phase. The quantity structures are extended in accordance with the available quantities for profinet IO. Parameter limits are not exceeded during configuration.