faria gauge pii

1 1 of 14 2003-2005 American Honda Motor Co., Inc. All Rights ReservedINSTALLATION INSTRUCTIONS* The water pressure gauge and analog hour meter are not included in the 5 gauge should be ordered THESE INSTRUCTIONS CAREFULLY Proper assembly and installation is essential for safe, reliable operation. Wear protective gloves when handling parts with sharp PARTS LISTR emove all kit parts from the box, and check all parts against the following MeterApplicationFaria 5 gauge Set*Publication NumberHonda CodePII53606 AOutboardsWhite faced, flat lens06300-ZW5-010ZB6315410 Issue DateBlack faced, flat lens06300-ZW5-010ZA6315402 October 2005 DescriptionPart NumberHonda CodeWater Pressure gauge (white face, flat lens)38351-ZW5-000ZB6831473 Water Pressure gauge (black face, flat lens)38351-ZW5-000ZA6831481 Analog Hour Meter (white face, flat lens)39700-ZW5-000ZB6077788 Analog Hour Meter (black face, flat lens)

2 39700-ZW5-000ZA5977780 Use the faria instrument harness (P/N 32103-ZW7-010AH) to connect faria gauges to the Honda main harness (refer to page 5 of 14).RefQtyDescription11 Speedometer21 Mounting Bracket31 Rubber Hose42 Female Connector52 Brass Nut62 Split Washer71 Red Lens82 Cable TieRefQtyDescription11 Tachometer21 Mounting Bracket37 Brass Nut45 Split Washer51 Red Lensonpqrstuonpqr2 of 14 2003-2005 American Honda Motor Co., Inc. All Rights ReservedFuel GaugeTrim MeterVolt MeterWater Pressure gauge (not included in the 5 gauge set)Analog Hour Meter (not included in the 5 gauge set)RefQtyDescription11 Fuel Gauge21 Mounting Bracket36 Brass Nut43 Split Washer51 Red LensRefQtyDescription11 Trim Meter21 Mounting Bracket34 Brass Nut42 Split Washer51 Red LensRefQtyDescription11 Volt Meter21 Mounting Bracket34 Brass Nut42 Split Washer51 Red Pressure Gauge21 Mounting Bracket31 Rubber Hose42 Brass Nut52 Split Washer611/8" NPT Fitting71 Red Lens82 Cable Tie91 Adaptor 1/8" NPTF To BSPTRefQtyDescription11 Analog Hour Meter21 Mounting Bracket32 Split Washer42 Brass Nut51 Red LensUse the faria Instrument Harness (P/N 32103-ZW7-000AH) to connect faria gauges to the Honda main harness (refer to page 5 of 14).

3 Onpqronpqronpqronpqrstuv1/8" NPTF (National Pipe Thread- female)1/8" BSPT (British Pipe Thread- male)onpqr3 of 14 2003-2005 American Honda Motor Co., Inc. All Rights the negative battery a mounting location for the appropriate gauge (s) that provides easy readability from the operator s position. Check behind each mounting hole location for sufficient installation a hole in the dash for each gauge to the specification the gauge in its mounting hole and check the necessary, install the red lens over the light bulb before installing the gauges:a. Twist the black socket assembly one-eighth turn counterclockwise and remove Pull the bulb straight out of the Slip the red lens over the bulb and install the socket the gauges with mounting brackets, split washers, and brass nuts as shown starting on the next page.

4 Tighten the nuts until the gauge can no longer be rotated in the not overtighten the mounting nuts. Overtightening the nuts may crack the gauge housing, mounting bracket, or mounting "Tachometer3-3/8" Trim Meter2-1/16" Volt Meter2-1/16"Fuel Gauge2-1/16"Water Pressure2-1/16"Hour Meter2-1/16"LIGHT SOCKETLIGHT SOCKETLIGHT BULBRED LENS4 of 14 2003-2005 American Honda Motor Co., Inc. All Rights ReservedGAUGE INSTALLATION SpeedometerFuel GaugeTachometerWater Pressure GaugeTrim MeterHour MeterVolt MeterTachometer Selector Switch Setting:Using a small screwdriver, SLIGHTLY depress and turn the selector switch to the desired setting.* BF40/50 - 2005 and previous BF40/50 - 2006 and subsequentDASH3-3/8" diameter holeMOUNTING BRACKETSPLIT WASHER (2)BRASS NUT (2)DASH2-1/16" diameter holeSPLIT WASHER (2)BRASS NUT (3)MOUNTING BRACKETDASH3-3/8" diameter holeSPLIT WASHER (2)MOUNTING BRACKETBRASS NUT (2)SELECTOR SWITCH (see below)BRASS NUT (2)MOUNTING BRACKETSPLIT WASHER (2)DASH2-1/16" diameter holeMOUNTING BRACKETBRASS NUT (2)SPLIT WASHER (2)BUSHING (2)DASH2-1/16" diameter holeBRASS NUT (2)MOUNTING BRACKETSPLIT WASHER (2)DASH2-1/16" diameter holeBRASS NUT (2)MOUNTING BRACKETSPLIT WASHER (2)DASH2-1/16" diameter hole5 of 14 2003-2005 American Honda Motor Co.

5 , Inc. All Rights ReservedELECTRICAL the the faria instrument harness to the Honda key switch panel or side mount remote control harness as the instrument lighting as shown using the instructions below.#1 Instrument lights operate when Honda key switch is red/white wire to the black/yellow wire.#2 Instrument lights operate when boat light switch is red/white wire and black/yellow wires to the boat light LIGHT SWITCHFARIA HARNESSKEY SWITCH PANEL OR SIDE MOUNT REMOTE CONTROLPink wire from boat fuel tank sending 10 amp power trim/tilt MAIN HARNESS6 of 14 2003-2005 American Honda Motor Co., Inc. All Rights the faria instrument harness end to the instruments as instrument harness terminal ends are covered for insulation purposes.

6 Remove the covering only on the terminal ends used for gauges that are installed. Leave the covering on unused terminal the wire terminals with the hardware as GAUGETRIM METER(+) TERMINAL(-) TERMINALRUBBER HOSE CONNECTION (page 8 of 14)BLACKRED/WHITESPLIT WASHER (3) S POST GND POST I POSTPINK (from the boat sender unit)BRASS NUT (3)BLACK/YELLOWRED/WHITEBLACK B+ POST SIG POSTSPLIT WASHER (3) GND POSTBLACK/YELLOWBLACKRED/WHITEBLACKYELLO W/BLUELIGHT TERMINALSBRASS NUT (3)7 of 14 2003-2005 American Honda Motor Co., Inc. All Rights the rubber hose for the speedometer (page 8 of 14) and water pressure gauge (page 10 of 14). connecting the battery, recheck all electrical connections and make sure all mounting hardware is the battery and check the operation of each METERWATER PRESSURE BAT POST SIG POST GND POSTGRAYBRASS NUT (2)SPLIT WASHER (2)BLACK/YELLOWBLACKRED/WHITELIGHT TERMINALBRASS NUT (2)SPLIT WASHER (2) + POSTBLACK/YELLOW G POSTBLACKRED/WHITELIGHT TERMINALRED/WHITEBLACKRUBBER HOSE CONNECTION (page 10 of 14)8 of 14 2003-2005 American Honda Motor Co.

7 , Inc. All Rights ReservedHOUR METERThis hour meter will operate as long as the ignition switch is in the RUN position, and will not operate when the ignition switch is in the STOP faria wire harness does not have connections for the faria hour meter. If the faria wire harness is used with the faria gauge set (or individual gauges), tap off any of the black/yellow wire posts with a wire and connect to the hour meter + terminal. Tap off any of the black wire posts with a wire and connect to the hour meter required: Use stranded, insulated wire not smaller than18 AWG that is approved for marine use. Use insulated " female spade connectors on hour meter connections. Use eyelet terminals to connect to the faria the battery and test the lighting WATER installing the speedometer in the dash, connect the rubber hose to the back of the speedometer and secure with a cable the rubber hose back to the motor alongside the control cables.

8 A slight downward slope from bow to stern will help avoid trapping water. Avoid sharp turns, crimping, kinking, or other forces that may reduce the inside diameter of the hose. Do not coil any excess rubber hose. Carefully measure, then cut to the desired NumberHonda CodeFemale Spade Connector07 VPZ-001050A5816574 Eyelet Terminal07 VPZ-001060A5816582 + POST G POSTBLACKVOLT METERBLACK/YELLOWFARIA HARNESSRUBBER HOSENIPPLECABLE TIE9 of 14 2003-2005 American Honda Motor Co., Inc. All Rights the rubber hose at regular intervals with small plastic wire ties (again be careful to not pinch the tubing). at the top of the swivel case, route the rubber hose over the top of the steering arm, down through the inside of the swivel case alongside the shift rod, and out the bottom of the swivel case to the pitot approximately 1/8" (3 mm) off the nipple the pitot tube if it is clogged with salt or any other foreign the hose to the appropriate length to reach the nipple the end of the hose over the nipple and secure it with a cable feed the pitot tube and rubber hose back up through the swivel case until a slight loop is made in the pitot the hose to the steering arm with cable approximately 1/8" (3 mm)

9 Off the pitot tubing nipple end that extends from the rigging the pitot tubing if it is clogged with salt or any other foreign the rubber hose to the appropriate length to reach the nipple the end of the hose over the nipple and secure with a cable HOSESTEERING ARMPITOT TUBESWIVEL CASESHIFT RODCUT ABOUT 1/8" (3 mm)NIPPLEPITOT TUBERUBBER HOSECABLE TIEPITOT TUBINGNIPPLERUBBER HOSECABLE TIECUT ABOUT 1/8" (3 mm)10 of 14 2003-2005 American Honda Motor Co., Inc. All Rights ReservedMAINTENANCEThe pitot tube should be flushed with fresh water before storing the boat for prolonged periods. Any remaining water in the rubber hose should also be removed before storing the boat for prolonged the pitot tube or rubber hose should become the rubber hose from the speedometer and the pitot the rubber hose with a stiff wire or blow air though not blow air through the rubber hose when it is connected to the speedometer.

10 High air pressure will damage the and clean the pitot tube with fresh water. If necessary, clean the pitot tube opening with a stiff the rubber hose to the speedometer and secure with a new cable the rubber hose to the pitot tube nipple end and secure with a new cable PRESSURE gauge RUBBER installing the water pressure gauge in the dash, connect the rubber hose to the back of the water pressure gauge and secure the hose with a cable the rubber hose back to the motor alongside the control cables. A slight downward slope from bow to stern will help avoid trapping water. Avoid sharp turns, crimping, kinking, or other forces that may reduce the inside diameter of the hose.