FIRST Robotics Competition Pneumatics Manual - …

1 FIRST FRC Pneumatics Manual Page 1 of 23 FIRST Robotics Competition Pneumatics Manual The FIRST Robotics Competition (FRC) pneumatic components are outlined in this document. It is being provided as a courtesy, and therefore does not supersede any information or rules provided in the FIRST Robotics Competition Manual . For official questions, please go to the FIRST Forums at FIRST , the FIRST logo, FIRST Robotics Competition , Coopertition , Gracious Professionalism , and Sport for the Mind are trademarks of the United States Foundation for Inspiration and Recognition of Science and Technology ( FIRST ).

2 2016-2017 FIRST . All rights reserved. FIRST FRC Pneumatics Manual Page 2 of 23 Contents pneumatic Advantages .. 3 pneumatic Components .. 4 Pneumatics Control Module .. 4 Compressor .. 5 Pressure Relief Valve .. 5 Pressure Switch .. 6 Air Tank .. 6 Regulators .. 7 Electric valves .. 7 Gauges .. 8 Parker Fittings .. 8 Tubing .. 9 Custom Bimba Cylinders .. 9 Pneumatics Setup .. 10 Compressor and Relief Valve .. 10 Pressure Switch, Gauge, and Plug Valve .. 11 Regulator and Gauge .. 12 Actuation .. 12 Electrical Valve.

3 13 Air Tank .. 13 Plumbing .. 14 Wiring .. 14 Setup .. 15 Calibration of Relief Valve .. 15 16 Cylinder Length Example .. 17 Appendix 18 Example On Board Setups .. 18 Example Off Board Setups .. 19 Appendix B .. 20 Appendix C .. 23 FIRST FRC Pneumatics Manual Page 3 of 23 pneumatic Advantages Fluid power technology encompasses both hydraulics and Pneumatics . Hydraulic applications use pressurized fluids, mostly oil, while pneumatic applications use pressurized gases, mostly air. Mobile construction equipment uses a hydraulic pump mounted on the engine.

4 The outlet of the pump is plumbed to a set of valves . Each valve is then plumbed to a cylinder. This allows you to distribute power from the engine all around the equipment. The same is true for an FRC robot. Once you install the compressor operating one valve and cylinder combination, you ve done most of the work. To add an additional valve and cylinder combination, you just tee into the pressure line, add in the additional circuit, and update your code. Weight - Compare the weight of several valves and cylinders to that of the motors, gears, belts, and chains used on some lift mechanisms and you will find the weight comparable, if not much lighter.

5 Simple to Design - Using Pneumatics is much easier than building a motor; gear, chain and sprocket lift mechanism. Once you have reviewed the layout in Appendix A, you will find it very easy to build a circuit. Adjustable Force - To adjust the force of the cylinder, all you have to do is adjust the regulator in front of it. The force is equal to the area of the cylinder piston times the pressure. Remember that the valves need a minimum of 15 30 psi to work properly. Durable - All of us have problems burning up motors from time to time.

6 You can stall an air cylinder against a load indefinitely and turn off the compressor. The materials provided are industrial grade products. Strong - Teams have the option of using a small bore cylinder at 20psi, a medium cylinder at , or a large 2 cylinder. By varying the pressure to the cylinders, you can produce a force from 9 pounds up to 180 pounds, depending on your needs. Custom Cylinders and a Rotary Actuator - You can order the cylinder you need for the job, listed in Appendix C. Last Minute Additions - At the last minute, you can add a cylinder and valve very quickly.

7 FIRST FRC Pneumatics Manual Page 4 of 23 pneumatic Components Below are the components needed to set up an FRC Pneumatics system. Pneumatics Control Module Cross the Road Electronics Pneumatics Control Module (PCM) is in each Rookie Kit. The PCM is used to control the compressor, solenoids, and pressure switch. The pressure switch should be wired into the 2 Weidmuller ports labeled PRESSURE SW , while the compressor s red and black wires should go directly into the red and black COMPRESSOR OUT Weidmuller connectors.

8 The PCM can control 8 single solenoid valves or 4 double solenoid valves . It also supports both 12 and 24 volt solenoids however, only one voltage may be used at a time. This 12 or 24 volt selection is done by relocating the jumper in the VSOL slot. The solenoids provide in the Rookie Kit and via FIRST Choice is 24 volt so make sure the jumper is in the correct location before turning on. Finally the PCM receives power from the PDP via the 2 Vin connectors and signal from the 4 CAN connectors.

9 The PCM will handle turning the compressor on and off based on the state of the pressure switch and the Enable state of the robot. If any Solenoid Valve object is opened (LabVIEW) or constructed (C++/Java) in your code, the PCM compressor control will be automatically enabled. FIRST FRC Pneumatics Manual Page 5 of 23 Compressor Compressors are in each rookie team s Kickoff Kit and available through FIRST Choice for 2015. The compressor is a Viair 090C Air Compressor. It will put out approximately 120psi before the relief valve opens.

10 Because the compressor can produce a significant amount of vibration, we recommend that you use vibration isolation mounts that come preinstalled on the compressor. In order for these to isolate the vibration, they need to be mounted to a stiff piece of material, such as a 1/4 aluminum plate. The compressor can also get very hot and should not be in direct contact with anything else. The compressor should be wired directly to the COMPRESSOR OUT Weidmuller connectors on the pneumatic control module (PCM).