Example: quiz answers
Fixing Guide - Tapco Roofing Products
screws (using hammer/screwdriver or nail/screw-gun). Longer 2" (50mm) nail or outdoor Phillips bugle screw required for fixing ridges and hips. Corrosion resistant fasteners are always recommended, especially in coastal areas. In Scotland we recommend the use of Stainless Steel nails for fixing. 7.1mm diameter nail heads are recommended when ...
Tags:
Information
Domain:
Source:
Link to this page:
Related documents
Hand Arm Vibration Ready Reckoner - Speedy Hire
www.speedyservices.comNail Guns 06/0265 <2.5 Staple Gun Gas IM200 08/0622 18 Cartridge Tool DX460 08/0657 <2.5 Nail Gun Gas Paslode IM250 (2nd Fix) 08/0658 9 Strip Nailer Gas IM350 (1st Fix) 08/0660 2.5 Portanailer Kit 08/0661 9 Angled Brad Nailer Gas IM250a 08/0663 9 Concrete & Steel Nail Gun 08/0680 <2.5 Milwaukee C12PN-0 Cordless Palm Nailer Drills
Air & Water Barrier Membrane - Henry
henry.comConcrete . ASTM C836 load suction pressure-Low Temperature Flexibility and Crack Bridging @ –20°C . ASTM C836 -Aging-Long Term Flexibility . CGSB 71 -GP-24M -Nail Sealability . ASTM D1970 --Resistance to Mold, Mildew & Fungal growth . ASTM D5590 . ASTM E84-VOC Content . Gray . 60% . 10.8 lbs/gal (1.3 kg/l) 2 Hours to touch dry . 24 Hours to ...
INTERIOR FINISH OF WALLS AND CEILINGS
www.constructionknowledge.netThe drywall nail most frequently used is the annular ring nail. This nail fastens securely into wood studs and joists. When purchasing such nails, consider the thickness of the layer or layers of drywall, and allow additional length for the nail to penetrate the underlying wood 3/4 inch. Example: 1/2-inch drywall plus 3/4-inch
Nail Gun Safety - Occupational Safety and Health ...
www.osha.govNail gun injuries are common—one study found that 2 out of 5 residential carpenter apprentices experienced a nail gun injury over a four-year period. When they do occur, these injuries are often not reported or ... concrete. The guide assumes that contractors are generally familiar with how nail guns work and the various types of specialized ...
DOMESTIC DECK DESIGN GUIDE - TasmanKB
www.tasmankb.com.auGenerally machine driven nails are proprietary to the nailing gun manufacturer and are not referenced in AS1684. Machine driven nails can be used as long as the nail has the same capacity as the hand driven nails detailed in Table 3. T …
NEW CONSTRUCTION, REPLACEMENT AND FLUSH FIN ... - Ply …
homedepot.plygemwindows.comthe nail holes in the nail fin. NOTE: For aluminum or aluminum-clad windows, sealant must be applied directly over any joints located at the corners. The bottom nail fin must have a continuous bead of sealant applied. (See Figure A). 2. Leave two 2” skip gaps per unit in the sealant creating a discontinuous bead of
Controlling Noise on Construction Sites - LHSFNA
www.lhsfna.orgModifying - Pneumatic Nail Gun Problem: Sound level from pneumatic nail guns 94.5 dB(A) (at muffler) Solutions: Improving the existing muffler Incorporating some type of return or exhaust line Acoustically Treated Noise Level: Avg. Sound Pressure Level With Treatment - 75.5 dB Avg. Sound Pressure Level Without Treatment - 94.5 dB Costs:
GoBoard - Johns Manville
www.jm.comAppropriate roofing nail or backer board screw fastening device (nail gun on a lower pressure setting or drill). Caulk Gun Paint Brush Putty Knife 3/16" V-Notch Utility Knife Pencil Tape Measure 1/4" x 1/4" Square -Notch 1/2" Drill Bit (if using Jig Saw) Thin Set mixing tools are also needed Drywall T-Square Rubber Mallet Straight Edge (for ...