Flush Door Series Hollow Core

1 Part 1: : Subject to local building codes, this product is intended foruse Single family dwelling interior Multifamily dwelling, low-rise professional office, library and low-rise motel interior Lighter use industrial building and factory, hotel, and retail salesbuilding interior Description: 1-3/4 or 1-3/8 side-hinged door systemsmanufactured by Door system components include: door panel(s), bifold panel(s),door frame, 2: BASIC Panel: Masonite Flush doors shall be fabricated using looselay up assembly that includes wood veneer or hardboard facings, woodor MDF stiles, wood or MDF rails and corrugated cell core.

2 Door facingsare to be bonded to stiles, rails and core forming a 3-ply structuralattachment. Mounting surface for latching hardware to be reinforced with solidinternal support. Hinge preparations for 1-3/8 thick doors to bemachined for standard weight radius mortise 3-1/2 hinges and 1-3/4 thick doors to be machined to accept 4 hinges. Latch preparations areto be placed in the area of solid internal supports. Face bore(s) forcylindrical lock and deadbolt are to be 2-1/8 diameter at 2-3/4 or2-3/8 Vertical edge of door to be square , beveled both sides or lock stileonly.

3 Edge preparation should be clearly noted when the product Panel: Masonite Flush bifolds shall be fabricated usingloose lay up assembly that includes wood veneer or hardboard facings,wood or MDF stiles, wood or MDF rails and corrugated cell core. Bifoldfacings are to be bonded to stiles, rails and core forming a 3-plystructural Frame: Wood jambs shall be fabricated as a flat jamb withdoorstop applied or 2-piece split jamb. Hinge jamb preparations for1-3/8 thick doors to be machined for standard weight radius mortise3-1/2" hinges and 1-3/4 thick doors to be machined to accepts 4 hinges.

4 Strike jamb preparations are to be machined for full lipcylindrical strike plate. Double door units shall include preparations forball catch located at the top of door on both door panels designed tostrike into the head : (3) standard weight radius mortise hinges are required ondoors 7 0 height or smaller & (4) on doors greater than 7 0 .Part 3: DELIVERY, STORAGE & : Reasonable care shall be exercised during shipping andhandling in keeping with the decorative nature of & Protection: Store upright in a dry, well ventilated build-ing or shelter at a constant temperature.

5 Do not store in damp, freshlyplastered, drywall or concrete areas until materials have completelydried. Doors should be stored at least 10 away from any heat source tohelp prevent uneven drying. Doors must be sealed with an oil-basedsealer or primer if stored for long 4: : Site verification of substrate conditions, which havebeen previously completed, are acceptable for the product installationinstructions in accordance with manufacturer s specifications. Verifythat door frame openings are constructed plumb, true and level beforebeginning installation process.

6 Select fasteners of adequate type,number and quality to perform the intended : Remove protective packaging just prior to shall be experienced in performing work required and shall bespecialized in the installation of work similar to that required for thisproject. Comply with manufacturer s product data, including producttechnical bulletins, product catalog installation instructions and productpackaging instructions for : See Masonite - How ToPaint and How ToStaininstructions for complete finishing details. Various types ofmaterials are used in the construction of the door system; each shall besealed in accordance with manufacturer sspecifications to protect againstvarious environmental conditions.

7 Make sure to completely seal andinspect all 6-surfaces (top, hinge side, bottom, lock side, front face andback face) with two coat minimum on operable panel(s). Finishing and/orre-finishing must be completed immediately after door has acclimated tothe environment where it is to be installed and within a maximum of 7days. Avoid finishing after a rain or damp and during periods of higherthan average humidity. Conduct periodic inspections of all coated surfacesto insure that door components are not exposed. Inspections should occurat least once a year.

8 Reseal the surface as 5: GENERAL Performance: Unit scheduled for installation in openingrequiring a specific noise control rating shall be clearly noted whenproduct is ordered. 1-3/8 thick Flush door with wood veneer facingsand corrugated cell core sound transmission class (STC) rating is 24.(See acoustical performance data for unit specific acoustical information.)Part 6: Limited 1-Year - Please check with manufacturer or distributor forcurrent warranty terms and WoodOr MDFH inge StileCorrugated Cell( Hollow Core)Wood Veneer orHardboard FacingsOptional WoodOr MDFB ottom RailFlush Door SeriesHollow CoreInterior DoorsOur continuing program of product improvement makes specifications,design and product detail subject to change without notice.

9 2007 Masonite International Corporation. All Rights Wood Or MDFTop RailOptionalWoodOr MDFLock StileInternalSupportForLatchingHardwar