FR-A7ND E kit INSTRUCTION MANUAL - VFDs.com

1 FR-A7ND E kit INSTRUCTION MANUALCINVERTERINVERTERPlug-in optionINSTRUCTION MANUALINVERTER12345678 HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPANFR- a7nd E kit communication functionIB(NA)-0600342 ENG-C(1209) MEEP rinted in JapanSpecifications subject to change without INSTRUCTIONSINSTALLATIONWIRINGINVERTER SETTINGFUNCTIONSOBJECT MAP DEFINITIONSTROUBLESHOOTINGOBJECT MAPA-1 Thank you for choosing this Mitsubishi inverter plug-in INSTRUCTION MANUAL gives handling information andprecautions for use of this equipment. Incorrect handling mightcause an unexpected fault. Before using the equipment, pleaseread this MANUAL carefully to use the equipment to its forward this MANUAL to the end Electric Shock PreventionThis section is specifically about safety mattersDo not attempt to install, operate, maintain or inspect thisproduct until you have read through this INSTRUCTION MANUAL andappended documents carefully and can use the equipmentcorrectly.

2 Do not use this product until you have a fullknowledge of the equipment, safety information this INSTRUCTION MANUAL , the safety INSTRUCTION levels areclassified into "WARNING" and "CAUTION".Incorrect handling may causehazardous conditions, resulting indeath or severe handling may causehazardous conditions, resulting inmedium or slight injury, or maycause only material level may even lead to a seriousconsequence according to conditions. Both INSTRUCTION levelsmust be followed because these are important to INSTRUCTIONSWARNING While the inverter power is ON, do not open the front cover orthe wiring cover. Do not run the inverter with the front coveror the wiring cover removed.

3 Otherwise you may access theexposed high voltage terminals or the charging part of thecircuitry and get an electric shock. Even if power is OFF, do not remove the front cover except forwiring or periodic inspection. You may accidentally touch thecharged inverter circuits and get an electric shock. Before wiring or inspection, power must be switched OFF. Toconfirm that, LED indication of the operation panel must bechecked. (It must be OFF.) Any person who is involved inwiring or inspection shall wait for at least 10 minutes after thepower supply has been switched OFF and check that thereare no residual voltage using a tester or the like. Thecapacitor is charged with high voltage for some time afterpower OFF, and it is dangerous.

4 Any person who is involved in wiring or inspection of thisequipment shall be fully competent to do the work. The plug-in option must be installed before wiring. Otherwise,you may get an electric shock or be injured. Do not touch the plug-in option or handle the cables with wethands. Otherwise you may get an electric shock. Do not subject the cables to scratches, excessive stress,heavy loads or pinching. Otherwise you may get an Injury Prevention3. Additional InstructionsAlso the following points must be noted to prevent an accidentalfailure, injury, electric shock, ) Transportation and mounting2) Trial run3) Usage4) Maintenance, inspection and parts replacement5) Disposal6) General instructionCAUTION The voltage applied to each terminal must be the onesspecified in the INSTRUCTION MANUAL .

5 Otherwise burst, damage,etc. may occur. The cables must be connected to the correct burst, damage, etc. may occur. Polarity must be correct. Otherwise burst, damage, etc. mayoccur. While power is ON or for some time after power-OFF, do nottouch the inverter as they will be extremely hot. Doing so cancause Do not install or operate the plug-in option if it is damaged orhas parts missing. Do not stand or rest heavy objects on the product. The mounting orientation must be correct. Foreign conductive objects must be prevented from enteringthe inverter . That includes screws and metal fragments orother flammable substances such as Before starting operation, each parameter must be confirmedand adjusted. A failure to do so may cause some machines tomake unexpected Do not modify the equipment.

6 Do not perform parts removal which is not instructed in thismanual. Doing so may lead to fault or damage of the When parameter clear or all parameter clear is performed, therequired parameters must be set again before starting operationsbecause all parameters return to the initial value. Static electricity in your body must be discharged before youtouch the product. Otherwise the product may be damaged. CAUTION Do not test the equipment with a megger (measure insulationresistance).CAUTION This inverter plug-in option must be treated as of the diagrams and drawings in this INSTRUCTION Manualshow the inverter without a cover or partially open forexplanation. Never operate the inverter in this manner.

7 Thecover must be reinstalled and the instructions in the invertermanual must be followed when operating the CONTENTS 1 PRE-OPERATION and Product Confirmation .. LED (operation status indication) .. instructions .. Procedure .. Address Setting ..123 to inverter List .. address (Pr. 345) .. baud rate (Pr. 346).. Mode Setting .. mode mode switching and communication startup mode (Pr. 79, Pr. 340) .. and Speed Command Source (Pr. 338, Pr. 339, Pr. 550) .. EEPROM write selection (Pr. 342) .. at Communication Error Occurrence .. selection at communication error occurrence (Pr. 500 to Pr. 502) .. and measures .. Reset .. and Speed Conversion Specifications ..425 from the inverter to the to the inverter from the OBJECT MAP Model of DeviceNet Communication.

8 Level of Polling I/O .. level of explicit message .. for Software Developers ..47 III7 OBJECT 0x01 (Identity-Object).. 0x01 Instance 0 .. 0x01 Instance 1 .. 0x03 (DeviceNet Object) .. 0x03 Instance 1 .. 0x04 (Assembly Object).. Instance 20/Input Instance Instance 21/Input Instance Instance 126/Input Instance 0x05 (DeviceNet Connection Object).. 0x05 Instance 1 Attribute (Explicit message connection) .. 0x05 Instance 2 Attribute (Polling I/O connection) .. 0x05 Instance 4, 5, 6 Attribute (Explicit message connection) .. 0x05 Instance 1, 2, 4, 5, 6 0x28 (Motor Data Object) .. 0x28 Instance 1 .. 0x29 (Control Supervisor Object) .. 0x29 Instance 1 .. 0x2A (AC Drive Object) .. 0x2A Instance 0x66 (Extended Object I).

9 0x66 Instance 1 .. 0x67 (Extended Object II).. 0x67 Instance 1 .. Class 0x70 to 0x79 (Extended Object III) .. Class 0x70 to 0x79 Instance 1, 2 .. Class 0x80 (Extended Object IV) .. Class 0x80 Instance 1 .. FR-E5ND (FR-E500-KND) Compatible TROUBLESHOOTING92 APPENDIX93 EDS File ..93 Error Code and Product ConfirmationTake the plug-in option out of the package, check the product name, and confirm that the product is as youordered and product is a plug-in option for the FR-E700 series SERIAL numberCheck the SERIAL number indicated on the rating plate or the 200V class of FR-E700, this option can be used with the inverter having the following SERIAL number or later. (For the 400V class of FR-E700, this option can be used with all inverters regardless ofSERIAL number.)

10 Z SERIAL number checkRefer to the INSTRUCTION MANUAL of the inverter for the location of the rating to {{{{{{ to {{{{{{ {{{{{{FR-E720-11K, 15KG7Y{{{{{{Rating plate example 7Y{{{{{{SERIAL (Serial No.)Symbol YearMonthControl numberThe SERIAL consists of one symbol, two characters indicating production year and month, and six characters indicating control last digit of the production year is indicated as the Year, and the Month is indicated by 1 to 9, X (October), Y (November), or Z (December).2 PRE-OPERATION Product confirmationCheck the enclosed items.*Used with the (FR-E720-175) or less and (FR-E740-170) or screw (M3 6mm).. 2 (Refer to page 8, 10.)Terminal 1 (Refer to page 8, 10.)Front cover for plug-in protective 1*Option small cover (Not used).}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}