G120 Parameter Manual - Tecno Ingenieria Industrial

1 S SINAMICS G120 G120 Control Units CU240S CU240S DP CU240S DP-F CU240S PN Firmware version Manual Edition 05/2007 Edition 05/2007 SINAMICSSINAMICS G120 Control Units CU240 SParameter ManualEdition 05/2007, Firmware version ACsParameters1 Function diagrams2 Faults and Alarms3 ASCII-TableAList of AbbreviationsBIndexCCopyright Siemens AG 2007 All Rights ReservedThe distribution and duplication of this document or the utilization and transmission of its contents are not permitted without express written permission.

2 Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are AGAutomation & DrivesStandard DrivesPostfach 3269, 91050 ErlangenGermanyDisclaimer of LiabilityWe have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

3 Siemens AG 2007 Technical data subject to GuidelinesThis Manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the Manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of more than one degree of danger is present, the warning notice representing the highest degree of dan-ger will be used.

4 A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property PersonnelThe device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety prac-tices and UsageNote the following:TrademarksAll names identified by are registered trademarks of the Siemens AG.

5 The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the that death or severe personal injury will result if proper precautions are not that death or severe personal injury may result if proper precautions are not a safety alert symbol, indicates that minor personal injury can result if proper precautions are not a safety alert symbol, indicates that property damage can result if proper precautions are not that an unintended result or situation can occur if the corresponding information is not taken into device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens.

6 Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and AktiengesellschaftSINAMICS G120 Control Units CU240 SInhalt-5 Siemens AG 2007 All Rights ReservedSINAMICS G120 Control Units CU240S, Edition 05/2007 Contents1 parameters .. to parameters .. of parameters .. and Drive Data Sets Overview .. Data Sets (CDS) .. Data Sets (DDS) .. (BICO)- parameters .. Input parameters .. Input parameters .. Output parameters .. Output parameters .

7 Output parameters .. commissioning (P0010 = 1).. 1-3132 Function diagrams .. : function diagrams .. in funktion diagrams .. Interfaces .. Setpoint Source .. Functions .. Function Blocks.. Channel .. Control .. Control .. 2-3643 Faults and Alarms.. and Alarms Overview .. of Fault and Alarm messages .. 3-379 AASCII-Table .. A-405 BList of Abbreviations .. B-407 CIndex .. C-413 ContentsInhalt-6 Siemens AG 2007 All Rights ReservedSINAMICS G120 Control Units CU240S, Edition 05/20071-7 Siemens AG 2007 All Rights ReservedSINAMICS G120 Control Units CU240S, Edition 05 to of and Drive Data Sets (BICO) commissioning (P0010 = 1)

8 1-313 ParametersIntroduction to Parameters1-8 Siemens AG 2007 All Rights ReservedSINAMICS G120 Control Units CU240S, Edition 05 to ParametersThe layout of the Parameter description is as 1-1 Read-only 1-2 Write parameterParameter numberIndicates the relevant Parameter number. The numbers used are 4-digit numbers in the range 0000 to 9999. Only for PROFINET there are a few parameters in the range of Numbers prefixed with an r indicate that the Parameter is a read-only Parameter , which displays a particular value but cannot be changed directly by specifying a different value via this Parameter other parameters are prefixed with a P.

9 The values of these parameters can be changed directly in the range indicated by the Min and Max settings in the header. If these values have a physical unit, it is shown in brackets.[index] indicates that the Parameter is an indexed Parameter and specifies the range of indices indicates that the Parameter has several bits, which can be evaluated or connected ,&2 LI H[LVW &8 6&2 $GGLWLRQDO WRUTXH VHWSRLQW &2 $GG WUT VHW$FFHVV OHYHO 3 *URXS &ORVHG ORRS FRQWURO8 QLW 'DWD VHW ''6'DWD W\SH )ORDWLQJ 3 RLQWU U %,&2 LI H[LVW &8 6 '3 &8 6 '3 )6 HOFWLRQ RI FRPPDQG VRXUFH &RPPDQG VRXUFH VH$FFHVV OHYHO 4 XLFN FRPP 12&DQ EH FKDQJHG 70LQ 3 *URXS &RPPDQGV$FWLYH <(68 QLW 0D[ 'DWD W\SH 8 QVLJQHG 'DWD VHW &'6)]]]

10 DFWRU\ VHWWLQJ 3 > @3 > @,QGH[&8 30 YDULDQWV Introduction to ParametersParameters1-9 Siemens AG 2007 All Rights ReservedSINAMICS G120 Control Units CU240S, Edition 05/2007 Parameter text (Long name/Short name)Indicates the name of the relevant Parameter names include the following abbreviated prefixes: BI, BO, CI, CO and CO/BO followed by a abbreviations have the following meanings:To make use of BICO you will need access to the full Parameter list. At this level many new Parameter settings are possible, including BICO functionality.]