GENERAL DESCRIPTION PRODUCT DATA (continued)

1 Architectural Coatings Pitt-GlazeWB1 Interior Semi-Gloss Pre-Catalyzed Water-Borne Acrylic EpoxyGENERAL DESCRIPTIONPRODUCT data ( continued )9-100 SeriesRECOMMENDED USESFEATURES / BENEFITSPitt-Glaze WB1 Water-Borne Acrylic Epoxy is a one-componentacrylic epoxy semi-gloss coating for interior use and is a low-odorreplacement for traditional two component acrylic epoxy productsproviding a recoatable, impact and mildew-resistant finish. Thisproduct meets the strictest VOC regulations with a VOC content ofless than 100 g/L and its minimal odor makes Pitt-GlazeWB1 suit -able for hospitals, schools, cafeterias and food processing plants,or any area that cannot be taken out of service for an extendedperiod of time.

2 Do not use in household dwellings. This item is intended forindustrial use only and should only be applied by item is for use in areas such as office spaceand meeting rooms of industrial, commercial or institutional facili-ties exposed to repeated heavy abrasion, including mechanicalwear and repeated scrubbing with industrial solvents, cleaners, orscouring component, waterbased formulaNo mixing or measuring and unlimited pot lifeLess than 100 g/L VOC contentMeets the most stringent regulatory standardsExcellent abrasion and impact resistanceLonglasting protectionExcellent chemical and stain resistanceExtends substrates lifeLower odor than two-componentCan be applied in occupied areas Excellent mildew resistant coatingResists mildew/fungus/biological growth on the paint filmExcellent block resistance Tack free film / ideal for doors, doorframes.

3 And windowsillsCan help earn LEED2009 creditsContributes to sustainable designPERFORMANCE DATACONFORMANCE STANDARDSVOC compliant in all regulated areasMeets MPI Category #153, Light Industrial Coating,Interior WB Semi-Gloss, Gloss Level 5 Can help earn LEED 2009 creditsMeets the Collaborative for High Performance Schools(CHPS) Low-Emitting Materials criteria section 01350 APPLICATION INFORMATIONStir thoroughly. Apply with a high quality brush, roller, paint pador by spray equipment. Read all label and Material Safety DataSheet (MSDS) information prior to use.

4 MSDS are availablethrough our website or by calling 1-800-441-9695. Airless Spray: Pressure 2000 psi, tip - Spray equipment must be handled with due care and inaccordance with manufacturer s recommendation. High-pressureinjection of coatings into the skin by airless equipment may causeserious :Polyester/Nylon BrushRoller:3/8 - 3/4 nap roller coverThinning:No thinning is required. If necessary, thin with up to1/4 pt. (118 mL) of water per gallon ( L) of temperatures during application:Material:50 to 90 F10 to 32 CAmbient:50 to 90 F10 to 32 CSubstrate.

5 50 to 90 F10 to 32 CPITT-GLAZE 16-510 SeriesAluminumGalvanized SteelConcreteGypsum Wallboard-DrywallConcrete/Masonry BlockPlasterFerrous MetalWoodASTM 1308 Chemical ResistanceResultsAcid (10% hydrocholoric acid)ExcellentAcid (10% phosphoric acid)ExcellentAcid (10% sulfuric acid)ExcellentBase (25% sodium hydroxide) ExcellentCleaner (Fantastik )ExcellentGasolineExcellentMineral SpiritsExcellentWaterExcellentXyleneLimi tedPropertyTest MethodResultsImpact ResistanceASTM D2794 Forward -inch-pounds>100 Reverse -inch-pounds>100 Hardness (Konig Pendulum)ASTM D4366>25 Scrub Abrasive Media w/shimASTM 2486 Cycles to failure>700 Adhesion (Method A - X cut)ASTM D33595 ABlock ResistanceLaboratoryExcellentF41 COVERAGE:Approximately 200 to 400 sq.

6 (19 to 37 ) per gallon ( L) on nonporous Film to mils Wet Microns:102 to 204 Dry Film to milsDry Microns:38 to 76 Coverage figures do not include loss due to surface irregularitiesand porosity or material loss due to application method or TIME: Dry time @ 77 F (25 C); 50% relative Touch:1 hourTo Recoat:4 hoursDrying times listed may vary depending on temperature, humidity,film build, color, and air movement. CLEANUP:Clean tools with warm soapy :Contact your local environmental regulatory agencyfor guidance on disposal of unused PRODUCT .

7 Do not pour down adrain or storm POINT:Over 200 F (93 C) PRODUCT DATAPRODUCT TYPE:Acrylic EpoxyGLOSS:Semi-Gloss:50 to 70(60 Gloss Meter)VOLUME SOLIDS*:37% +/- 2%WEIGHT SOLIDS*:48% +/- 2%VOC*:95 g/L ( )WEIGHT/GALLON* lbs. ( kg) +/- lbs. (91 g)* PRODUCT data calculated on PRODUCT 16-510 SeriesArchitectural CoatingsPitt-GlazeWB1 Interior Semi-Gloss Pre-Catalyzed Water-Borne Acrylic EpoxyGENERAL SURFACE PREPARATIONF41 5/2013(Supersedes 4/2012)PACKAGINGRECOMMENDED PRIMERSPPG Architectural Finishes, Inc. believes the technical data presented is currently accurate: however, no guarantee of accuracy, comprehensiveness, or performance is given orimplied.

8 Improvements in coatings technology may cause future technical data to vary from what is in this bulletin. For complete, up-to-date technical information, visit our website or call 1-800-441-9695. PPG Industries, CoatingsOne PPG PlacePittsburgh, PA Services1-800-441-96951-888-807-5123 faxPPG Canada, Coatings4 Kenview BlvdBrampton, ON L6T 5E4 Architect/Specifier1-888-PPG-IDEA1-Gallo n ( L)5-Gallon ( L)LIMITATIONS OF USEFOR INTERIOR USE ONLY. Apply when air, surface and producttemperatures are between 50 F (10 C) and 90 F (32 C).Do not use on floors, in areas of saturating humidity, or onsubmerged surfaces.

9 For professional use only. Not intended forresidential use. PROTECT FROM this PRODUCT provides a mildew resistant coating, growthmay still occur if the substrate is not properly prepared prior topainting and/or if the substrate is consistently exposed toconditions conducive to mold, mildew, and algae. Examples ofthese conditions include, but are not limited to areas that areconsistently damp with little to no direct AND BASE INFORMATIONR efer to the appropriate color formula book, automatic tintingequipment, and or computer color matching system for colorformulas and tinting and Pastel Base16-540 Neutral Base**Must be tinted before colors, drastic color changes, or porous substrates mayrequire more than one coat to achieve a uniform , 90-712 Concrete4-603, 17-921 Concrete/Masonry Block6-15, 16-90 Ferrous Metal90-712.

10 90-912 Galvanized Steel17-921, 90-712 Gypsum Wallboard-Drywall 6-2, 6-4, 6-4900, 9-900, 17-921 Plaster4-603, 17-921 Wood6-2, 6-4, 6-4900, 9-900,17-921 Surfaces to be coated must be dry, clean, sound, and free from all contamination including loose and peeling paint, dirt, grease, oil, wax,concrete curing agents and bond breakers, chalk, efflorescence, mildew, rust, PRODUCT fines, and dust. Remove loose paint, chalk, andefflorescence by wire brushing, scraping, sanding, and/or pressure washing. Putty all nail holes and caulk all cracks and open all glossy, rough, and patched surfaces.