Geotechnical Design Standard – Minimum Requirements

1 Manual Geotechnical Design Standard Minimum Requirements December 2020 Transport and Main Roads, December 2020 Copyright The State of Queensland (Department of Transport and Main Roads) 2020. Licence This work is licensed by the State of Queensland (Department of Transport and Main Roads) under a Creative Commons Attribution (CC BY) International licence. CC BY licence summary statement In essence, you are free to copy, communicate and adapt this work, as long as you attribute the work to the State of Queensland (Department of Transport and Main Roads).

2 To view a copy of this licence, visit: Translating and interpreting assistance The Queensland Government is committed to providing accessible services to Queenslanders from all cultural and linguistic backgrounds. If you have difficulty understanding this publication and need a translator, please call the Translating and Interpreting Service (TIS National) on 13 14 50 and ask them to telephone the Queensland Department of Transport and Main Roads on 13 74 68. Disclaimer While every care has been taken in preparing this publication, the State of Queensland accepts no responsibility for decisions or actions taken as a result of any data, information, statement or advice, expressed or implied, contained within.

3 To the best of our knowledge, the content was correct at the time of publishing. Feedback Please send your feedback regarding this document to: Transport and Main Roads, December 2020 i Contents 1 Introduction ..1 2 Embankments ..3 General Requirements .. 3 Performance standards .. 4 Geotechnical Design for unreinforced embankments .. 7 Additional Design Requirements for side-long embankments .. 11 Embankment subject to permanent/semi-permanent toe inundation .. 13 Reinforced embankments .. 14 Ground improvement .. 14 Geotechnical instrumentation monitoring for embankments.

4 15 Maintenance .. 15 3 Cut slopes .. 16 General Requirements .. 16 Performance standards .. 16 Design Requirements .. 17 General .. 17 Unreinforced cuts .. 17 Reinforced cut slopes .. 19 Construction .. 20 4 Bridge and other structure foundations .. 21 General .. 21 Structural aspects .. 21 Geotechnical aspects Geotechnical investigation and reporting .. 21 Deep foundations .. 22 Design philosophy .. 22 Design methodology .. 23 Construction .. 26 Spread footings and strip footings .. 26 5 Retaining structures.

5 27 General .. 27 Embedded retaining walls .. 27 Reinforced concrete cantilever retaining walls .. 28 Soil nailed walls .. 28 Reinforced Soil Structure (RSS) walls .. 29 Gabion retaining walls .. 29 Boulder retaining walls .. 30 Introduction .. 30 Definition of 30 Materials .. 30 Design .. 30 Construction .. 32 Certification of retaining structures .. 32 Transport and Main Roads, December 2020 ii 6 Remediation of existing slopes and embankments .. 33 Design life for remediation 33 FOS to be used in the remediation Design .

6 33 7 High risk temporary work Design .. 34 8 References .. 35 Geotechnical Design Standard Minimum Requirements Transport and Main Roads, December 2020 1 1 Introduction a) The following clauses of this document outline the Minimum Geotechnical Requirements , which shall be met in the Design for all projects. The Requirements stipulated here are the Minimum Geotechnical Requirements and do not preclude the Designer from using other proven methods in addition to those identified within this document. Some construction Requirements that may impact the designs are also included.

7 B) Scope briefing for all Geotechnical works shall be acceptable to Transport and Main Roads Geotechnical Section before the commencement of any Geotechnical site investigation. Geotechnical site investigation shall be carried out in accordance with AS 1726 and logging of encountered subsurface materials during Geotechnical investigation shall be in accordance with the departmental Guideline on Geotechnical Logging. Where there is a conflict between AS 1726 and this Geotechnical Design Standard (GDS), the content of this GDS shall take precedence.

8 C) All Geotechnical Design reports, including drawings, shall be submitted to Transport and Main Roads Geotechnical Section in electronic format (and hard copy if requested) for review. The reports shall state clearly the assumptions, the justification of adopted Geotechnical profiles, parameters and the methods adopted in Design and address all relevant issues or concerns for the Design element in question. The reports shall also include Geotechnical long and cross-sections together with the site investigation location plan(s) drawn to the same horizontal scale for each Design element.

9 D) The establishment of a Geotechnical model in the context of this document shall generally be in accordance with the Requirements of Clause of AS 1726. However, for each Geotechnical Design element, the specific Minimum Requirements shall be in accordance with the relevant sections below. e) When the reports are submitted in stages (for example, concept, business case, detailed Design stages and so on), each report shall be a standalone report. At the end of the full review process, a final standalone Geotechnical report, including Geotechnical field and laboratory data, interpretative Design report(s) as per Clause 1(c) shall be submitted to Transport and Main Roads Geotechnical Section through the Administrator for their record.

10 F) The Design calculations, duly documented as the Design work progresses, shall be provided, on request, to the Administrator. The Administrator shall provide these reports to Transport and Main Roads Geotechnical Section. Geotechnical Design Standard Minimum Requirements Transport and Main Roads, December 2020 2 Notes: 1. Wherever the 'Administrator' is referred in this document, it shall be replaced with ' project Manager' for Design only Contracts. 2. Wherever "Transport and Main Roads Geotechnical Section" is referred, the contact person shall be Director ( Geotechnical ) or his / her nominee.