Hempel Book PC-MC June 2007

1 Product DataProduct DataProduct Data SheetHEMPELHEMPEL S ZP ALKYD primer 12090 Description: Hempel S ZP ALKYD primer 12090 is a relatively quick-drying, zinc phosphate primer ,based on long oil alkyd and urethane use: As a general purpose primer for HEMPALIN systems for protection of steel in mild tomedium atmospheric corrosive temperatures:Maximum, dry exposure only: 120 C/248 :Approved under Saudi Aranco s Engineering Standards APCS-4 and :Not included in Group Assortment. Local availability subject to CONSTANTS:Colours/Shade nos: Red/50410 - Yellow/2022 SFinish:FlatVolume solids, %:49 1 Theoretical spreading m /litre - 40 micron491 gallon - milsFlash point:38 C/100 FSpecific kg/litre - lbs/US gallonDry to touch:2-4 hours at 20 C/68 :410 g/litre - lbs/US gallonThe physical constants stated are nominal data according to the Hempel Group's approved formulas.

2 They aresubject to normal manufacturing tolerances and where stated, being standard deviation according to ISO DETAILS:Application method:Airless sprayAir SprayBrush/RollerThinner ( ):08230 (5%)08230 (15%)08230 (5%)Nozzle orifice:.018"Nozzle pressure:150 bar/2175 psi(Airless spray data are indicative and subject to adjustment)Cleaning of tools:THINNER 08230 Indicated film thickness, dry:40 mils (See REMARKS overleaf)Indicated film thickness, wet:75 milsRecoat interval, min:See REMARKS overleafRecoat interval, max:See REMARKS overleafSafety:Handle with care. Before and during use, observe all safety labels on packaging andpaint containers, consult Hempel Material Safety Data Sheets and follow all local ornational safety regulations.

3 Avoid inhalation, avoid contact with skin and eyes, and donot swallow. Take precautions against possible risks of fire or explosions as well asprotection of the environment. Apply only in well ventilated : January 2005 Page 1 of 2 Product Data SheetSURFACE New steel: Abrasive blasting to minimum Sa. For temporary protection, if required, use a suitablePREPARATION:shopprimer. Damage of shopprimer and contamination from storage and fabrication should bethoroughly cleaned prior to final repair and touch-up use Hempel S ZP ALKYD primer : Remove oil and grease, etc. with suitable detergent. Remove salt and othercontaminants by (high pressure) fresh water cleaning. Remove all rust and loose material byabrasive blasting, power tool cleaning or water jetting.

4 Dust off residues and allow the surface todry. Touch up to full film dictated by normal good painting :In confined spaces provide adequate ventilation during application and : SUBSEQUENT HEMPALIN qualities according to :REMARKS:Film thickness:May be specified in another film thickness than indicated depending on purpose and area of will alter spreading rate and may influence drying time and recoating interval. Normal rangedry is 30-50 :Recoating intervals related to later conditions of exposure:(40 mils dry film thickness of Hempel S ZP ALKYD primer 12090)3 days7 daysNoneNone8 hours2 days5 hours2 daysHEMPALIN, except 5324053240 MediumMildMediumMildAtmosphericAtmospher icRecoated with(Quality numbers only)20 C/68 F20 C/68 FSteel temperatureMaximumMinimumIf the maximum recoating interval is exceeded, roughening of the surface is necessary to ensureintercoat adhesion.

5 Before recoating after exposure in contaminated environment, clean surfacethoroughly with (high pressure) fresh water hosing and allow to : Hempel S ZP ALKYD primer 12090 is for professional use BY: Hempel PAINTS (SAUDI ARABIA) - 1209050410CS001 Issued: January 2005 Page 2 of 22/2 Hempel S ZP ALKYD primer 12090 This Product Data Sheet supersedes those previously issued. For explanations, definitions and scope, see Explanatory Notes in the Hempel , specifications, directions and recommendations given in this data sheet represent only test results orexperience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appro-priateness under the actual conditions of any intended use of the Products herein must be determined exclu-sively by the Buyer and/or User.

6 The Products are supplied and all technical assistance is given subject to Hempel 's GENERAL CONDITIONS OFSALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Sellerdisclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence,except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses ordamages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.