HOTEMP PLUS - יאיר ארז בע''מ

1 Print CIElementsprintGrafixHOTEMP plus , Prod. 002086, enEdition [replaces edition ] Benefits for your application Efficient lubrication even at high operating temperatures Good regeneration effect on used oil Favourable viscosity-temperature properties for safe cold starts Outstanding penetration properties for rapid formation of the lubricating film Good adhesion, no throwing off Resistance to wear and pressure Little residue owing to fully synthetic constituents Efficient against the settling of finishing and softening compounds and their condensates at the point of frictionDescriptionHOTEMP plus is a synthetic high-temperature chain oil fortextile and plastic processing machines ensuring reliableoperation even at high temperature and creeps very well and thus rapidly forms a lubricating specific additive combination makes HOTEMP plus is highlyresistant to pressure and wear.

2 Special adhesion improversprevent the oil being thrown off the lubrication plus is very efficient against the settling of finishingand softening compounds and their condensates at the point offriction. The few residues created by synthetic constituents areeasy to regenerate by adding fresh plus is suitable for all oil-lubricated stenter chainssuch as roller chains, chains or clips with ball bearings in cases of combinedlubrication of bearings, chain joints and slide ways, and slide chains with lubrication of slide rails, chain joints and boltsin equalizing frames, single-layer stenters, tier stenters, festoondriers and steamers as well as notesHOTEMP plus can be applied with all common pumps, sprayingor metering equipment. lubrication intervals and quantities varywith chain design, type of lubrication and operating conditions.

3 Attemperatures above 180 C, you need approx. to 2 ml of oilper meter of chain and operating rails should be lubricated continuously or once a day at amaximum, depending on length of travel and design. Weeklyrelubrication is often sufficient for chain pins with an oil , it is better to apply an exact dosage of oil every daythan relubricate too late or over-lubricate, especially at high with a spray lubrication system should be lubricated verysparingly once per shift or day to keep them just safety data sheetsMaterial safety data sheets can be requested via our You may also obtain them through yourcontact person at Kl ber PLUSHigh-temperature chain oilProduct informationPack sizes HOTEMP + plus +Canister 5 l+Canister 20 l+Drum 200 l+Product dataHOTEMP + plus +Article number002086 Chemical composition, type of oilester oil Chemical composition.

4 Type of oilsynthetic hydrocarbon oil Upper service temperature250 C / 482 FAppearanceclear Density, DIN 51757, 20 Capprox. g/cm Colour spacegreen Flash point, DIN EN ISO 2592, Cleveland, open-cup apparatus>= 220 CKinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 100 Capprox. 28 mm /sKinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 40 Capprox. 320 mm /sViscosity index, DIN ISO 2909>= 110 Minimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopenedoriginal container, monthsKl ber lubrication your global specialistInnovative tribological solutions are our passion. Throughpersonal contact and consultation, we help our customersto be successful worldwide, in all industries and our ambitious technical concepts and experienced,competent staff we have been fulfilling increasinglydemanding requirements by manufacturing efficient high-performance lubricants for more than 80 ber lubrication M nchen SE & Co.

5 KG /Geisenhausenerstra e 7 / 81379 M nchen / Germany /phone +49 89 7876-0 / fax +49 89 data in this document is based on our general experience and knowledgeat the time of publication and is intended to give information of possibleapplications to a reader with technical experience. It constitutes neither anassurance of product properties nor does it release the user from theobligation of performing preliminary field tests with the product selected for aspecific application. All data are guide values which depend on the lubricant'scomposition, the intended use and the application method. The technicalvalues of lubricants change depending on the mechanical, dynamical, chemicaland thermal loads, time and pressure. These changes may affect the functionof a component.

6 We recommend contacting us to discuss your specificapplication. If possible we will be pleased to provide a sample for testing onrequest. Kl ber products are continually improved. Therefore, Kl berLubrication reserves the right to change all the technical data in this documentat any time without and Copyright: Kl ber lubrication M nchen SE & Co. KG. Reprints,total or in part, are permitted only prior consultation with Kl ber LubricationM nchen SE & Co. KG and if source is indicated and voucher copy company of the Freudenberg GroupHOTEMP PLUSHigh-temperature chain oilProduct informatio