INSTALLATION INSTRUCTIONS - American …

1 Place back-up nuts on both bottom bolts, andthe top left-hand bolt the two lower back-up nuts so that frontface of nuts is flush with finished waste horn to project 5/16" fromfinished a level, adjust the top left back-up nut so thatit is in the same vertical plane as the lower left back-upnut. (If wall surface is irregular, the three back-upnuts must be positioned to allow a minimum 1/16"gap between fixture and wall surface.)NOTE: Bearing nuts and washers must be setto take full loading from the fixture allowing1/16" clearance between fixture and support manufacturer's recommendedsetting of closet outlet felt or neoprene gasket (wax ring notrecommended) on closet the fixture is installed, closet outletgasket must be compressed sufficiently toassure a gas and watertight bowl on support using cap nuts and fiberwashers with the back-up nuts and NOT APPLY TOP RIGHT FIBER WASHERAND CAP NUT UNTIL OTHER CAP NUTSHAVE BEEN FIRMLY TIGHTENED USING top right cap nut with fiber washer andrun up hand tight.

2 Wrench tighten approximately1/4 sealant to gap between bowl and finishedwall. Remove excess A V E F O R F U T U R E U S E1730480-100 Rev B730480-100 Rev B730480-100 Rev B730480-100 Rev BSaniwaresProduct names listed herein are trademarks of American Standard Inc. American Standard Inc. 2006 SPONGEWASHERTANK to INSTRUCTIONS supplied with wall carrier for proper INSTALLATION of 4-bolt support system wall cavity requirements and rough-in information for waste outlet piping.!- 2 -78 ADJUSTMENTSThe flushometer tank is designed and factory-adjusted to provide a consistent, safe seal depth in the bowl after each flush. Field refill adjustment is not required. The refill has been preset and locked. FLUSH ACTUATOR ADJUSTMENT - The spacing between the bellcrank and flush actuator may be adjusted to assure positive operation of the trip lever. Proceed as follows: Remove tank cover and check that there is approximately 1/32" ( ) gap between the top of the actuator and bottom of the spring rod when it is lifted to remove slack from linkage.

3 If necessary, loosen set screw in actuator cap and turn cap to increase gap (clockwise) or decrease gap (counterclockwise), as needed. Tighten setscrew securely after adjustment is completed. Replace tank AND CLEANING When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's PARTS LISTNOTE: "XXX" and "YYY" represent color or trim finish options. Specify when LEVER-LHTRIP LEVER-RHTANK (COMPLETE WITH COUPLINGCOMPONENTS AND TANK TRIM)TANK (COMPLETE WITH COUPLINGCOMPONENTS AND TANK TRIM)TANK COVERBOWLSPRING ROD ASSEMBLY-LHSPRING ROD ASSEMBLY-RHCOUPLING GASKETLOWER SUPPLY ASSEMBLY (35 PSI)UPPER SUPPLY ASSEMBLYVALVE CARTRIDGE ASSEMBLYTANK COUPLING KITTANK COVER FOR LOCKING DEVICECOVER LOCKING DEVICE KITTANKCOUPLING NUTFLEXIBLESUPPLYWATER INLETCOMPRESSIONCOLLARWASHERVALVE NUTTRIM PLATEVALVE1234 5897 6 10- 3 -SETSCREW1/32" ONE-YEAR LIMITED WARRANTYIf inspection of this American -Standard plumbing product, within one year after its initial INSTALLATION , confirms that it is defective in materials or workmanship, American -Standard will repair or, at its option, exchange the product for a similar model.

4 This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before warranty shall be void if the product has been moved from its initial place of INSTALLATION ; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American -Standard's INSTRUCTIONS ; or if it has been modified in a manner inconsistent with the product as shipped by 's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or INSTALLATION , nor shall American -Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty.

5 (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:- 4 -TROUBLESHOOTING GUIDENOTE: The presence of a small amount of water in the bottom of the tank is normal. The air inducer is designed to leak for short periods during each flush cycle as a self-cleaning action. Drippage is drained into the bowl. If used on water system containing excessive sand and/or debris, a periodic cleanup of inlet strainer is recommended.

6 (See enclosed INSTRUCTIONS for strainer cleaning.) ! WARNINGWhen servicing or replacing components of the flushometer tank system, be sure that thewater supply is shut off and the toilet is flushed to relieve pressure in the flushometer service of the Flushometer Tank System, see enclosed literature. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Does not flush a. Water supply valve closed. a. Open valve and allow water to fill tank. b. Flush actuator incorrectly set. b. Follow instruction to adjust flush actuator. c. Supply line blocked. c. Shut off water supply, disconnect supply line, and inspect all gaskets and washers. Reassemble. d. Trip lever linkage damaged. d. Check trip lever, linkage, and spring rod assemblies for or sluggish a. Supply valve partly closed. a. Open supply valve fully.

7 Be sure that proper supply tubeflush size is used. b. Plugged inlet strainer. b. Remove and clean strainer per enclosed INSTRUCTIONS c. Supply pressure too low. c. Normal supply pressure must be at least 25 psi. d. Partially clogged trapway and/or d. Remove obstruction. Consult a plumber if necessary. drain pipe and/or vent. e. Malfunctioning pressure regulator. e. Replace lower supply leaks a. Poor supply line connection. a. Review Step 7 of INSTALLATION procedure. b. Poor bowl to wall waste outlet b. Review Step 3 through 5 of INSTALLATION procedure. connection. c. Tank/bowl connection. c. Check tank for movement. Refer to Step does not a. Supply pressure too low. a. Normal supply pressure must be at least 25 off b. Flush actuator incorrectly set. b. Follow INSTRUCTIONS to adjust flush the United States: American Standard Inc., Box 6820 Piscataway, New Jersey 08855 Attention: Director of Consumer AffairsFor residents of the United States,warranty information may also beobtained by calling the followingtoll free number: (800) Canada: American -Standard, 2480 Stanfield RoadMississauga, Ontario Canada L4Y 1S2 Toll Free: (800) Mexico:Customer Service Manager Ideal Standard, de Morelos #330 Col.

8 Santa ClaraEcatepec 55540 Edo. Carrier SupportPutty KnifeRegular ScrewdriverAdjustable WrenchSealantTape MeasureFlexible Supply TubeCarpenters LevelRECOMMENDED TOOLSAND MATERIALSM odel 2093 ElongatedGLENWALL GPF TWO-PIECEPRESSURE-ASSISTEDWALL-MOUNTED TOILETSINSTALLATION INSTRUCTIONST hank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure thisproduct is installed properly, please read these INSTRUCTIONS carefully before you begin. (Certain installations may require professional help.) Also be sure your INSTALLATION conforms to local : PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FORHANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!NOTE: For proper operation product requires a minimum of 25 psi working line pressure30(762mm)OR32(813mm)14-3/4(375mm )9(229mm)29-1/2(749mm)7-1/2(191mm)191mm( 7-1/2)14-1/2(368mm)OR16-1/2(419mm)C/L OF WASTEOUTLET(4) 7/8(22mm) DIA. HOLESSUPPLY ASREQUIRED*5/8(16mm)3-1/4(83mm)1-1/2(38m m)5-1/4(133mm)3-7/8(98mm)FINISHED WALLFIN.

9 FLOOR3-1/4(83mm)3/4 (19mm) (152mm)8-1/2(216mm)4-1/8(105mm)OR6-1/8(1 56mm)19-1/2(495mm)C/LFINISHED WALLCLOSETCARRIERSYSTEM(3) NUTSWASTEHORN5/16 LEVELFINISHED WALLFIXTURE MOUNTINGF ixture studs should project2-1/8" from face of finished ViewSide ViewFINISHED WALL2-1/8"(4) STUDS1/16" (IRREGULARWALL SURFACE)Install large rubber gasket over threaded outlet onbottom of tank with tapered side out and lower tank ontobowl so that the tapered end of gasket fits evenly intobowl water inlet opening, and tank mounting bolts gothrough mounting holes. Secure with metal washersand tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against sanitary bar toilet seat according to manufacturer's : DO NOT OVERTIGHTENNUTS MORE THAN REQUIREDFOR A SNUG FIT!INSTALL TANK AND TOILET SEATThe following steps require a helper:Connect water supply line between shutoff valve and tank water inlet fitting. Tighten coupling nuts securely.

10 Turn on supply valve and allowflushometer tank to for leakage at fittings,tighten or correct as WATER SUPPLYM eets the American Disabilities Act Guidelines and ANSI for the Physically ChallengedWhen installed, top of seat is17" to 19" (432mm to 483mm)from the finished floor.!Place back-up nuts on both bottom bolts, andthe top left-hand bolt the two lower back-up nuts so that frontface of nuts is flush with finished waste horn to project 5/16" fromfinished a level, adjust the top left back-up nut so thatit is in the same vertical plane as the lower left back-upnut. (If wall surface is irregular, the three back-upnuts must be positioned to allow a minimum 1/16"gap between fixture and wall surface.)NOTE: Bearing nuts and washers must be setto take full loading from the fixture allowing1/16" clearance between fixture and support manufacturer's recommendedsetting of closet outlet felt or neoprene gasket (wax ring notrecommended) on closet the fixture is installed, closet outletgasket must be compressed sufficiently toassure a gas and watertight bowl on support using cap nuts and fiberwashers with the back-up nuts and NOT APPLY TOP RIGHT FIBER WASHERAND CAP NUT UNTIL OTHER CAP NUTSHAVE BEEN FIRMLY TIGHTENED USING top right cap nut with fiber washer andrun up hand tight.