Transcription of Installation Manual
1 1 Heat & Glo COSMO-I30-IFT, COSMO-I35-IFT Installation Manual 2535-980 Rev. T 2/22 Installation ManualInstallation and Appliance SetupCAUTION! Risk of Fire! DO NOT store instruction manuals inside fireplace cavity. High temperatures could cause a fire. INSTALLER: Leave this Manual with the appliance, not inside the appliance. CONSUMER: Retain this Manual for future reference. Do not store inside the appliance NOTICE: DO NOT discard this Manual !This appliance may be installed as an OEM Installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 in the United States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH Series, in appliance is only for use with the type(s) of gas indicated on the rating plate.
2 This appliance is not convertible for use with other gases, unless a certified kit is used. DO NOT store or use gasoline or other flam-mable vapors and liquids in the vicinity of this or any other appliance. What to do if you smell gas - DO NOT try to light any DO NOT touch any electrical switch. DO NOT use any phone in your Leave the building Immediately call your gas supplier from a neighbor s phone. Follow the gas sup-plier s If you cannot reach your gas supplier , call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas : FIRE OR EXPLOSION HAZARDF ailure to follow safety warnings exactly could result in serious injury, death, or property damage.
3 DANGERHOT GLASS WILL CAUSE NOT TOUCH GLASS UNTIL ALLOW CHILDREN TO TOUCH barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and must be installed for the protection of children and other at-risk : COSMO-I30-IFTCOSMO-I35-IFTPour demander un exemplaire en fran ais de ce manuel d Installation , visitez 2 Heat & Glo COSMO-I30-IFT, COSMO-I35-IFT Installation Manual 2535-980 Rev. T 2/22 Safety Alert Key: DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
4 CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE: Used to address practices not related to personal injury. Note: The term recommend or recommended does not indicate a requirement. It is a best practice suggested by Hearth & Home Technologies .Table of ContentsInstallation Standard Work Checklist ..31 Product Specific and Important Safety Information A. Appliance Certification ..4B. Glass Specifications ..4C. BTU Specifications ..4D. High Altitude Installations ..4E. Non-Combustible Materials Specification.. 4F. Combustible Materials Specification.
5 4G. Electrical Codes ..4H. California ..42 Getting Started A. Design and Installation Considerations ..5B. Good Faith Wall Surface ..7C. Tools and Supplies Needed ..7D. Inspect Appliance and Components ..73 Appliance / Fireplace Requirements and Clearances A. Appliance/Decorative Barrier Front Dimension Diagrams .8B. Minimum Fireplace Opening ..13C. Zero Clearance Wall Extension ..15D. Mantel, Wall Projections, & Hearth Extensions ..17E. Hearth Extension / Vinyl Flooring ..184 Installation Preparation A. Cleaning ..20B. Flue Damper.. 20C. Gas Line ..20D. Fireplace Conversion Notice ..20E. Electrical Outlet Box.
6 205 Installing Vent Pipe and Appliance A. Vent Limits ..21B. Using Vertical Restrictor ..22C. Venting Components ..23D. Connecting to SLP ..24E. Connecting Vent Pipe ..25F. Placing, Securing and Leveling the Appliance ..26G. Installing Termination Cap ..276 Electrical Information A. General Information ..28B. Wiring Requirements ..29C. Installation / Service for Fan ..307 Gas Information A. Fuel Conversion ..31B. Gas Pressure ..32C. Gas Connection ..32D. High Altitude Installations ..33E. Air Shutter Setting ..33F. Service / Replace Appliance Gas Valve ..338 Finishing A. Mantel, Wall Projections & Hearth Extensions.
7 34B. Hearth Extension ..359 Appliance Setup A. Fixed Glass Assembly ..37B. Remove the Shipping Materials ..38C. Clean the Appliance ..38D. Accessories ..38E. Magic Glass Panels ..39F. Glass Media / Stone Placement ..41G. Install Decorative Barrier Front and Surround ..42H. Appliance Break-In ..43I. Heat Management ..4310 Reference Materials A. Vent Components ..44B. Accessories ..45 = Contains updated information. 3 Heat & Glo COSMO-I30-IFT, COSMO-I35-IFT Installation Manual 2535-980 Rev. T 2/22 Installation Standard Work ChecklistCustomer: Lot/Address:Model (circle one): COSMO-I30-IFT, COSMO-I35-IFTDate Installed: Location of Fireplace:Installer:Dealer/Distributor Phone # Serial #:Comments: Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective action needed _____Comments Communicated to party responsible _____ by _____on _____ (Builder / Gen.)
8 Contractor/) (Installer) (Date) Appliance Install YES IF NO, WHY?Verify fireplace is clean and remove/block open damper/modify damper for vent pipe clearance (Section 4). _____Locate multi-purpose tool (Section 2). _____ Appliance is leveled and secured (Section ). _____ Venting/Chimney Section 5 Exhaust and inlet flex vent pipe are properly formed and routed through existing fireplace damper. _____Exhaust and inlet flex vent pipe are properly installed to the correct collars, sealed and secured to top slide plate and to the termination cap.
9 _____Vertical restrictors are properly set (if applicable). _____ Exterior roof flashing installed and sealed. _____Termination cap installed, secured and sealed to top slide plate. _____Electrical Section 6 Unswitched power (110-120 VAC) provided to the appliance. _____Switch wires properly installed. _____Gas Section 7 Proper appliance for fuel type. _____Was a conversion performed? _____Leak check performed and inlet pressure verified. _____Verified proper air shutter setting for Installation type. _____Finishing Section 8 Combustible materials not installed in non-combustible areas.
10 _____Verified all clearances meet Installation Manual requirements. _____Mantels and wall projections comply with Installation Manual requirements. _____Appliance Setup Section 9 All packaging and protective materials removed (inside & outside of appliance). _____Refractories, logs, media and embers installed correctly. _____Glass assembly and glass seal plate installed and secured. _____Accessories installed properly. _____Surround and decorative front properly installed. See instructions shipped with appliance front. _____Manual bag and all of its contents are removed from inside/under the appliance and given to party responsible for use and operation.
