Installation, peration and Maintenance Manual
ROOF CAP* (with built-in damper) FAN HOUSING POWER CABLE* ROUND DUCT* ROUND ELBOWS* Seal gaps around Housing. Seal duct joints with tape. OR Keep duct runs short. WALL CAP* (with built-in damper) Energy Star® Certified Fan Model/Size Recommended Duct Dimensions SP-A70, SP-A90, SP-A50-90-VG, SP-A90-130-VG, SP-B70, SP-B80, SP-B90 6 …
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Minimum 180 in-lb Torque Applications
content.greenheck.comFor damper areas up to 45 sq-ft*(For lower torque, see AF, NFB, LF, ... Time to fit your Specific Application with Belimo’s Flexible Line of ... done in accordance with the damper manufacturer’s specifications. Control is On/Off from an auxiliary contact, or a manual switch. ...
Modular Make-Up Air Unit - content.greenheck.com
content.greenheck.comModular Make-Up Air Unit Model MSX Commercial, Industrial, and Kitchen Applications ... supply air for general, process and combustion exhaust. ... • Airflow Arrangement - Optional Variable Air Volume or Constant Volume 100% Outdoor Air • Performance Range - 800 to 7,500 cfm ...
Heating and Ventilating Units - content.greenheck.com
content.greenheck.com2 Heating Options Hot water, steam and electric heat options are available. The heating section consists of a factory-installed heating coil in a pre-engineered housing.
Energy Recovery and Make-Up Air Start-Up Report
content.greenheck.com5 Condenser Airflow S 6 6 4 8 5 3 4 12 4 1 2 14 13 11 10 9 Supply Airflow P1 P2 T1 T2 Packaged DX Cooling with Digital Scroll Compressor Water-Source Heat Pump with Standard Scroll Compressor
Indirect Gas-Fired Make-Up Air - content.greenheck.com
content.greenheck.com5 Controls Discharge Temperature Control In make-up air units, the unit-controlled heat output is based on discharge temperature. A factory-mounted
High Performance Vane Axial Fans - content.greenheck.com
content.greenheck.comfi 2 Model RA High Performance Vane Axial Fans RA high performance, direct-driven vane axial fans are ideal for inline air ventilation in commercial, institutional or industrial buildings.
Centrifugal Ceiling Exhaust and Inline Cabinet Fans
content.greenheck.com3 Model Comparison Model Location Mounting Airflow Application Drive Type Impeller Type Performance Outdoor Indoor Roof Curb Base/Floor Hanging Wall Ceiling Mounted Exhaust Supply Reversible Recirculate General/Clean Air Contaminated Air Spark Resistant Grease (UL 762) Smoke Control (UL) High Wind (150 mph) High Temp (above 200°F ) Belt Direct Centrifugal Propeller/Axial …
FumeJet Exhaust Systems - content.greenheck.com
content.greenheck.com2 Greenheck’s FumeJet® line of exhaust fans with integral stacks are designed to safely remove and disperse fumes and odors. FumeJet systems replace utility set fans with field supplied intake
Installation, Operation and Maintenance Manual
content.greenheck.comUpblast Centrifugal Roof Exhaust 3 ® When lifting a Belt Drive unit onto the roof, use either the four lifting points on the drive frame or the two lifting
BSQ Centrifugal Inline Fan - content.greenheck.com
content.greenheck.comBSQ Centrifugal Inline Fan New Dimensions Supplement Belt Drive July 2015 BSQ Redesign In early 2015, the BSQ was redesigned. The redesign changes some mounting dimensions
Related documents
Inch Series Flat Socket Head Cap Screws
www1.mscdirect.comThe length of a flat socket head cap screw is measured from the top of the head to the flat of the point unlike other socket products whose length measurement is from underneath the head to the flat of the point. Applicable Standards: ASME B18.3 and ASTM F835. Hardness: R C 37-44. Tensile Strength: 180,000psi min 5/8” diameter and smaller. 13
FastFire 3 User Guide Layout 1 10/2/15 8:55 AM Page 1
www.burrisoptics.com• 2 #6x48 Screws with Torx®socket head for installing the sight on the mounting plate ... To insert or replace the battery, unscrew the battery cap on the top of the sight using a slot head screwdriver. Make sure that that the positive pole of the battery is …
Guide, User, Sockets, Heads, Socket head, Fastfire 3 user guide, Fastfire
SERIES I MILLING MACHINES - Hardinge
www.hardinge.comholes serve to remove the nose cap with a spanner wrench). 1. Place the mounting ring (Item 11) underneath the top of the guard (Item 7). 2. Place two socket head cap screws (Item 12) through the holes in ring, and hand-start them into the threaded holes in the nose cap until hand tight. 3.
TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
nepp.nasa.govMIL-DTL-1222 - Studs, Bolts, Hex Cap Screws, Socket Head Cap Screws and Nuts MIL-I-24768/14 - Insulation, Plastic, Laminated, Thermosetting, Cotton-Fabric-Base, Phenolic-Resin (FBG) FEDERAL QQ-B-654 - Brazing Alloys, Silver QQ-S-698 - Steel, Sheet and Strip, Low Carbon TT-I-735 - Isopropyl Alcohol
PArts DIAGrAm & PArts lIst
www.minnkotamotors.comfl at head screwdriver, Phillips screwdriver, socket set, pliers, wire cutters. 52 | minnkotamotors.com ©2016 Johnson Outdoors Marine Electronics, Inc. PArts DIAGrAm & PArts lIst ... 230 2260221 VINYL CAP 1 232 2223100 NUT 5/16-18 NYLOCS SS 2 234 2263422 BOLT 5/16-18 X 1" SS 2
CAP SCREW HEAD WRENCH SIZE CHART - Imperial Supplies
www.imperialsupplies.comPhone: 1-800-558-2808. imperialsupplies.com. CAP SCREW HEAD WRENCH SIZE CHART. Imperial has made a concerted effort to provide accurate information in its catalog and on its web site, however Imperial assumes no responsibility for the accuracy of the information.
WEBER CARBURETOR CONVERSION KIT INSTALLATION GUIDE
www.quadratec.comMake a mark on the plastic choke cap and the carburetor where the two surfaces meet. Loosen the three screws one turn. Hold the throttle about one third open and start twisting the thermostat cap (counter clockwise) until the choke plates fully close, then slowly turn the cap 1/8” (you should feel the spring tension in the choke tightening).