Example: marketing
IronRidge Flush Mount Manual
seat roof screws and tighten hinge bolt to 225 in-lbs; RibBracket™ - firmly seat roof screws and tighten M8 bolt (M8-1.25 x 22mm sold separately) to 160 in-lbs; and SolarFoot™ - firmly seat roof screws and tighten M8 flange nut to 160 in-lbs. • ecoFasten Green Fasten GF-1 Anchors The general installation method for attachments is to
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Product Catalog
files.ironridge.comParts Catalog Overview Overview The IronRidge® Flush Mount System is a rail based system for mounting solar modules on pitched roofs. The system utilizes IronRidge XR Rails with a variety of roof attachments to support extreme wind and snow loads. The entire system uses only aluminum and stainless steel components to ensure complete corrosion ...
Engineering Down to the Deck - IronRidge
files.ironridge.comBuilt-in Waterproofing Sealed from above with a “blind hole” and pre-installed sealing washer, Flat Roof Attachment delivers integrated waterproofing with popular roofing systems, including single-ply and asphaltic. DECK BASE
IronRidge Ground Mount Installation Manual
files.ironridge.comAll electrical installation and procedures should be conducted by a licensed and bonded electrician or solar contractor. Routine maintenance of a module or panel shall not involve breaking or disturbing the bonding path of the system. All work must comply with national, state and local installation procedures, product and safety standards.
XR Rail Family - IronRidge
files.ironridge.comAnodizing prevents surface and structural corrosion, while also providing a more attractive appearance. XR Rail Family The XR Rail Family offers the strength of a curved rail in three targeted sizes. Each size supports specific design loads, while minimizing material costs. Depending on your location, there is an XR Rail to match.
Ground Mount System - IronRidge
files.ironridge.comThe IronRidge Ground Mount System combines our XR100 or XR1000 rails with locally-sourced steel pipes or mechanical tubing, to create a cost-effective structure capable of handling any site or terrain challenge. Installation is simple with only a few structural components and no drilling, welding, or heavy machinery required.
Related documents
Basic Roof Framing 17
wilswood.weebly.comParts of a Roof A basic, conventional roof consists of rafters, ceiling joists, and a ridge board, as shown in Figure 17-3. More complex roofs include other elements such as braces, valley rafters and jack rafters. (See Chapter 18, “Hip, Valley, and Jack Rafters.”) A rafter is an inclined member of the roof framework. Rafters serve the same ...
REPLACEMENT PARTS LIST CMF Series Downflow Furnace
www.yaunco.com104060000 SRJ1 Roof Jack Assembly 104060003 SRJ2 Roof Jack Assembly 104060015 SRJ3 Roof Jack Assembly 104060018 SRJ4 Roof Jack Assembly 104060024 SRJ5 Roof Jack Assembly ORDERING INFORMATION Please specify Model No. and Serial No. along with the exact part number(s) when ordering parts from the nearest authorized Dealer or Service Center.
Analysis and Design of Conventional Industrial Roof Truss ...
ijste.orgshorter parts. Fink trusses are utilized for long spans having high pitch roof, since the web members in truss are sub-divided to obtain shorter members. Fig. 3: Fink Truss Fan truss Fan trusses are format of Fink roof truss. In this, top chords are subdivided in smaller spans to supply supports for purlins which
Product Catalog
files.ironridge.comParts Catalog Overview Overview The IronRidge® Flush Mount System is a rail based system for mounting solar modules on pitched roofs. The system utilizes IronRidge XR Rails with a variety of roof attachments to support extreme wind and snow loads. The entire system uses only aluminum and stainless steel components to ensure complete corrosion ...
Parts of a Roof - Consumers' Checkbook
www.checkbook.orgParts of a Roof ! A few definitions may make it easier for you to communicate with roofers. Built-up Roof—A low-slope (or flat-seeming) roof covered with alternating layers of roofing felt and hot-mopped asphalt and topped off with a layer of gravel. Cornice—The wood or …
Installation Operation and Maintenance Manual
content.greenheck.comLocate parts far enough apart to permit air circulation, sunlight and space for periodic inspection. To minimize water accumulation, place all fan parts on blocking supports so that rain water will run off. Do not cover parts with plastic film or tarps as these cause condensation of moisture from the air passing through heating and cooling cycles.
Cat on a Hot Tin Roof - PBworks
shsdavisapes.pbworks.comCat on a Hot Tin Roof . Tennessee Williams . CONTENTS . ACT ONE . ACT TWO . ACT THREE (Original) ACT THREE (Updated) SHORT BIO . PERSON--TO--PERSON . EDITORIAL NOTE . STAGE CAST . MOVIE CAST . MUSICAL NOTE . ACT THREE ( With "Stage Management" and "Blocking Notations") The set is the bed-sitting-room of a plantation home in the Mississippi ...
ROOF AND GUTTER DE-ICING CABLE - Heat Trace Systems
www.heattracespecialists.comStanding Seam Metal Roof (Steel, Aluminum, opper, or10, Etc.) Use snow fence to prevent snow sliding. Use one run for each section, from gutter 2’-3’ up roof. Use an appropriate amount of heater cable in the gutter. Attach with RK-1 roof clips with GE Gray RTV-167 or attach with S-5 Mini clips as shown on “Page 7”. Standing Seam Metal Roof