KEYPAD OPERATION Te - all electro

1 altistart 48 Quick Reference Guide8636HO05013/2005 altistart 48rdYESCENTTeDRKEYPAD OPERATION3-character, 7-segment displayEnters a menu or a parameter, or saves the displayed parameter or valueReturns to the previous menu or parameter, or increases the displayed valueExits a menu or parameter, or aborts the displayed value to return to the previous value in the memoryAdvances to the next menu or parameter, or decreases the displayed valueNOTE: Pressing or does not store the choices. To store the displayed choice, press . The displayflashes when a value is display flashes when a value is stored. Some functions may require pressing the ENT button for two seconds to store the parameter TO PARAMETERSMenuParameterValue or assignmentNext parameterBrowsing within themenus1 flash(stored)INTRODUCTIONThis reference guide provides a brief overview of the altistart 48 (ATS48) soft start controllers' KEYPAD describing its OPERATION , how to access menus and parameters, as well as defining fault codes.

2 Refer to the ATS48 Soft Start Installation Guide (30072-450-61_) for complete soft start installation and programming instructions. For a list of general guidelines to troubleshoot the soft start based on the fault code displayed on its KEYPAD , refer to the maintenance, troubleshooting, and repair section of the ATS48 installation soft start statusACCESS TO MENUSS ettingsProtectionAdvanced settingsControl I/O Assignments2nd motor parametersCommunicationsSelected parameter displayed & locking codeAltistart 48 FamilyATS48D ATS48C ATS48M Courtesy of Steven Engineering, Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 8636HO0501 altistart 48 Quick Reference Guide3/2005 Schneider Electric USA8001 Hwy 64 EastKnightdale, NC 275451-888-SquareD (1-888-778-2733) / equipment should be installed, operated, serviced, and maintained only by qualified personnel.

3 No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. 2005 Schneider Electric All Rights ReservedSEt- BASIC SETTINGS MenuParameterCodeFactory SettingNominal motor currentCurrent limitAcceleration ramp timeInitial starting torqueType of stopDeceleration ramp timeFinal deceleration torqueImpulse braking torque levelDC injection braking timeInILtACCt90 StydECEdCbrCEbAVaries w/rating, A400% of In15 s20%-F- (Freewheel Stop)15 s20%50%20%PrO-PROTECTION MenuParameterCodeFactory SettingMotor overload protectionActivation of motor underloadMotor underload thresholdMotor underload timeExcessive starting timeActivation of current overloadCurrent overload thresholdCurrent overload timeLine phase reversal protectTime before restartingPhase loss thresholdMotor-monitoring PTC probesAutomatic restartReset motor thermal statetHPULLLULtULtLSOILLOCtOLPHrtbSPHLPt CArSrtHclass 10 OFF60%60 sOFFOFF80%10 sno2 s10%OFFOFF nodrC- ADVANCED SETTINGS MenuParameterCodeFactory SettingTorque li mi tVoltage boost levelTest on small motorTorque controlStator loss compensationDeceleration gainCascade function activationLine voltageLine frequencyReset kWh/elapsed timeReturn to factory settingstLIbStSStCLPLSCtIGCSCULnFrCrPrFC SOFFOFFOFFON50%40 %OFF460 VAUt (Automatic)

4 NonoI-O- I/O Control Terminal Settings MenuParameterCodeFactory SettingLogic inputsPreheating levelTime delay before preheatingLogic outputsRelay R1 Relay R2 Relay R3 Analog outputConfig. of analog output Scaling of analog outputL13L14 IPrtPrLO1LO2r1r2r3AO04 ASCLIA (Freewheel Stop)LIL (Forced Local)0%5 (Motor Thermal Alarm)rnl (Motor Powered)r1F (Fault Relay)(end of start)rnl (Motor Powered)OCr (Motor Current)020 (0 20 mA)200%St2- 2ND MOTOR PARAMETERS MenuParameterCodeFactory SettingNominal motor currentCurrent limitAcceleration ramp timeInitial starting torqueDeceleration ramp timeFinal deceleration torqueTo r qu e l i m i tDeceleration gainIn2IL2AC2t92dE2Ed2tL2tI2 Varies w/rating, A400% of In215 s20%15 s20%OFF40%COP- COMMUNICATIONS MenuParameterCodeFactory SettingSoft start addressCommunicaiton speedCommunication formatSerial link timeout settingRestore remote KEYPAD sOFFSUP- PARAMETER DISPLAYED MenuParameterCodeUnitPower factorMotor themal stateMotor currentElapsed operating timeActive powerActive power in kWMotor torqueDisplay of current stateLast detected faultPhase rotation directionKeypad display locking or kAh or kh%kW%TROUBLESHOOTINGF ault CodeDescriptionnLPrdYSoft start without run command and.

5 Line power not supplied Line power suppliedtbSStarting time delay not elapsedHEAM otor preheating in progress(Use SUP menu to set up monitoring parameter. Factory setting: Motor Current.)Soft start with run commandbrLSoft start brakingStbWaiting for a command (RUN or STOP) in cascade modeCFFI nvalid configuration on power-upCFII nvalid configurationCLFLoss of Control PowerEEFI nternal memory faultEtFExternal faultFrFLine frequency out of toleranceInFInternal faultLrFLocked rotor faultOCFO vercurrent faultOHFSoft start overheating faultOLCC urrent overload faultOLFM otor overload/ground faultOtFMotor thermal fault detected by PTC probesPHFLoss of line or motor phasePIFP hase reversal faultSLFS erial link faultStFExcessive starting timeULFM otor underload faultUSFLack of AC line power on a run commandNOTE: Please refer to the troubleshooting section of the ATS48 Soft Start Installation Guide (30072-450-61_) for complete installation and programming altistart Panel Mount Soft Startwith KEYPAD in of Steven Engineering, Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800)