Lodam Compressor Protection Modules Technical …

1 Lodam Compressor Protection ModulesTechnical manualVersion , B2, B3, B4 Page 2 Contents1. Read this first .. Reading instructions .. User manual .. Safety .. 42. General .. 53. Definitions .. 54. How to .. 65. Funtions .. 76. Examples of application use .. Connections .. 87. Technical data .. 138. Drawings .. 149. Standards .. 1510. Trouble shooting .. 1511. Index .. 1612. Notes .. 17 Technical manual SE-B1, SE-B2, SE-B3, SE-B4 Page 3 Page 41. Read this firstThe contents of this manual are subject to change without notice. Lodam electronics holds the copyright to this user s manual .

2 The user shall follow any instructions given in this user manual entirely and not only partly. Any non-follow-ing of this user manual result in exclusion of all warranties, guarantees, and liabilities. Copyright 2014 by Lodam electronics a/s. All Rights of the parts of the controller:INFORMATION FOR USERS ON THE CORRECT HANDLING OF WASTE ELECTRI-CAL AND ELECTRONIC EQUIPMENT (WEEE)In reference to European Union directive 2002/96/EC issued on 27 January 2003 and the related national legislation, please note that:1. WEEE cannot be disposed of as municipal waste and such waste must be collected and disposed of sepa-rately;2. The public or private waste collection systems defined by local legislation must be used.

3 In addition, the equip-ment can be returned to the distributor at the end of its working life when buying new equipment;3. The equipment may contain hazardous substances: the improper use or incorrect disposal of such may have negative effects on human health and on the environment;4. The symbol (crossed-out wheeled bin) shown on the product or on the packaging and on the instruction sheet indicates that the equipment has been intro-duced onto the market after 13 August 2005 and that it must be disposed of separately;5. In the event of illegal disposal of electrical and elec-tronic waste, the penalties are specified by local waste disposal Reading instructionsThe following symbols are used to draw the reader s attention to different warning !

4 ! General of electrical current or User manualBefore installation the user should be thoroughly familiarized with this user manual , especially with purposes, installation and care should be taken when installing and connect-ing external equipment (PTC sensor, high voltage etc) and handling the Modules correctly according to Protection against of the SE-B1/SE-B2/SE-B3/SE-B4 must be performed by authorized personnel only. All warranties are excluded in case installation is performed by unauthorized personnel or in case the SE-B1/SE-B2/SE-B3/SE-B4 has not been correctly SafetyThe SE-B1/SE-B2/SE-B3/SE-B4 is a Protection device and not a safety component according to the Machinery Directive and can not be used in medical or life support plant commissioning the service technician shall ensure that personal safety requirements are met in conformity with the Machinery Directive on the basis of safety plant failures are to be immediately solved, even though no immediate danger exists; the SE-B1/SE-B2/SE-B3/SE-B4 and motor must be without manual SE-B1, SE-B2, SE-B3, SE-B4 Page 52.

5 GeneralThe Protection devices SE-B1, SE-B2, SE-B3 and SE-B4. Hereafter SE-Bxare used for Protection of the motor against overheating by monitoring motor temperature by means of PTC-sensors mounted in the motors , other temperatures can be monitored by for example mounting PTC-sensors in the discharge outlet of a Compressor , for monitoring the oil temperature or the temperature in other areas where PTC-sensors are installed, they can also be monitored by a SE-Bx Protection module. Due to their fast reaction time, good accuracy and built-in relay they can be a good solution instead of a separate control-ler. They can also be used as switch SE-Bx is default wired up for lockout in case of an overheat situation, but can also be used as a thermostat/switch relay via the cool down period of the media sur-rounding the DefinitionsProduct rangeDefinitionsHWHardware/electronicsNC Normally Closed (relay)NONormally Open (relay)PTCP ositive Temperature Coefficient (sensor element)SE-BxA SE-B1, SE-B2, SE-B3 or SE-B4 Compressor Protection modulePage 64.

6 How toUse the SE-Bx in lockout mode SE-B1/SE-B2/SE-B3SE-B4 The wire jumper is default mounted in the two unnamed terminals located between terminals N and 12. In this mode a fault condition will need a manual reset to release the the SE-Bx in restart / hysteresis modeSE-B1/SE-B2/SE-B3SE-B4 The wire jumper between the two unnamed terminals is an overheat condition, the relay is energized again as soon as the resistance is below the lower threshold level of kOhm. There is no timer function in the manual SE-B1, SE-B2, SE-B3, SE-B4 Page 75. FuntionsThe SE-Bx is a motor Protection module. By monitoring the resistance in a PTC sensor, it will open its relay when the resistance of the PTC sensor increases above the limit as shown PTC-sensor could for example be according to DIN 44081/82.

7 The resistance of these PTC-sensors are not linear, but gives a steep rise in resistance when the thresh-old temperature of the PTC-sensor is reached. This is detected by the protective device and the relay is released and thereby cutting the control power as shown on the diagram below. RPTC (PTC re sistance) Close relay Closed Open Safety cha in (NC) 12 11 14 12 11 14 Ope n relay 2,7k 4,5k Relay RPTC (PTC re sistance) Not Loc kout Closed Open Safety cha in (NC) 12 11 14 12 11 14 Loc kout open relay Loc kout 2,7k 4,5k Relay Since the increase in resistance is so steep, from 1 up to 9 PTC-sensors can be coupled in series without raising the actual temperature threshold more than a few degrees there is a restart blocking wire jumper to prevent a motor from being started too soon after having been overheated.

8 A manual reset must be done by removing power from the module for minimum 5 seconds and then applying it the restart blocking wire jumper is removed, the relay behaves like on the following diagram. RPTC (PTC re sistance) Close relay Closed Open Safety cha in (NC) 12 11 14 12 11 14 Ope n relay 2,7k 4,5k Relay RPTC (PTC re sistance) Not Loc kout Closed Open Safety cha in (NC) 12 11 14 12 11 14 Loc kout open relay Loc kout 2,7k 4,5k Relay In this mode, there is a hysterese from 2,7kOhm to 4,5 kOhm. When the resistance in the PTC-sensors increases above 4,5 kOhm, the relay is released. The relay is released as long as the resistance is above 2,7 kOhm. When the resistance comes below 2,7 kOhm, the relay is hysteresis can be used for applications where the media where the PTC-sensors are mounted has such a large temperature inertia that this hysteresis is 86.

9 Examples of application ConnectionsTerminalDescriptionLPower supplyNNeutral11 Relay common12 Relay NO Error condition14 Relay NC Ok conditionUnnamedLockout wire jumperCompressor Protection module with a direct starting compressorMethod 1:19181716151413121110987654321L1L2L3 NPEF110Q1F2K111F1391U11W11V1M1M3R1 -3F34A0 1S1L1211B1 B2SE -B1SE -B2SE -B3SE -B4N1214R743H1F133 LNT2S0/220H2K111P>F5P<F6B1K2 T18K13/3/3 /12 /16/1718/19F4K111K111K111K111B2Y2Y3K2TR8F124A11 Pleasesee detailsregardingconnectioninsidethe terminalboxOptionTechnical manual SE-B1, SE-B2, SE-B3, SE-B4 Page 9 Method 2 3F34A0 1S1L1211B1 B2SE -B1SE -B2SE -B3SE -B4N1214R743F133H2P>F5P<F6B1K2 T18K13/3/3 /10 /1618 /19K111K111K111B2Y2Y3K2TR8F124A11 Pleasesee detailsregardingconnectioninsidethe terminalboxOptionS2H1K3F4 RedBrownOrangeBlackK111K391113K39 Compressor Protection module with a part winding 1.

10 19181716151413121110987654321L1L2L3 NPEF110Q1F2K111F1391U11W11V1M1M3R1 .. 6F34A0 1S1L1211B1 B2SE -B1SE -B2SE -B3SE -B4N1214R7H13/3/3 /10 /15/16/18/19K111R8F124A11 Pleasesee detailsregardingconnectioninsidethe terminalboxK214F1492W12U12V1145/5 /5 /17max secS2F133H2P>F5P<F6B1K2T18K1K111K111B2Y2Y3K2 TOptionK3 RedBrownOrangeBlackK111K39K39F145F4K214K1T1113K1 T12K215Y1K214K111 Page 10 Method 2:19181716151413121110987654321L1L2L3 NPEF110Q1F2K111F1391U11W11V1M1M3R1-6F34A0 1S1L1211B1 B2SE -B1SE -B2SE -B3SE -B4N1214R743H1F145 LNT2S0/220K111P>F5P<F6B1K2 T18K13/3/3 /12 /16/18/19F4K111K212K111K111B2Y2Y3K2TR8F1 24A11 Pleasesee detailsregardingconnectioninsidethe terminalboxOptionK212F1492W12U12V1F133H2 K2Y1K1 TK1 T13K2125/5 /5 /1712max secTechnical manual SE-B1, SE-B2, SE-B3, SE-B4 Page 11 Oil flow monitoring using the SE-B1/SE-B2/SE-B3/SE-B4 module.