Logix5000 Control Systems: Connecting PanelView …

1 Logix5000 Control Systems: Connect a PanelView Plus Terminal over an EtherNet/IP NetworkCatalog Numbers Logix5000 Controllers, 2711P PanelView Plus TerminalsQuick StartImportant User InformationSolid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication available from your local Rockwell Automation sales office or online at ) describes some important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is no event will Rockwell Automation, Inc.

2 Be responsible or liable for indirect or consequential damages resulting from the use or application of this examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is this manual, when necessary, we use notes to make you aware of safety , Compact I/O, CompactLogix, FactoryTalk, Integrated Architecture, Logix5000 , PanelView , POINT I/O, Rockwell Software, Rockwell Automation, RSLinx, RSLogix, RSNetWorx, Stratix 6000, and TechConnect are trademarks of Rockwell Automation, not belonging to Rockwell Automation are property of their respective : Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic : Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss.

3 Attentions help you identify a hazard, avoid a hazard, and recognize the HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous information that is critical for successful application and understanding of the Automation Publication IASIMP-QS033A-EN-P - March 20123 Table of ContentsPrefaceBefore Using This Publication .. 5 Other Logix5000 Control system Quick Starts .. 8 Use Each Chapter .. 8 Where to Start .. 9 How Hardware Is Connected .. 10 Required Software .. 10 Parts List .. 11 Additional Resources.

4 11 Chapter 1 Prepare the PanelView Plus Terminal HardwareBefore You Begin .. 13 What You Need .. 13 Follow These Steps .. 14 Mount the PanelView Plus Terminal .. 14 Connect the Power Supply .. 15 Connect the PanelView Plus Terminal to the EtherNet/IP Network .. 16 Assign an IP Address to the PanelView Plus Terminal .. 17 Additional Resources .. 19 Chapter 2 Create a PanelView Plus ApplicationBefore You Begin .. 21 What You Need .. 22 Follow These Steps .. 23 Install FactoryTalk View Studio Software .. 24 Install RSLinx Enterprise Software .. 28 Create a New Application .. 30 Create an RSLinx Enterprise Configuration in FactoryTalk View Machine Edition.. 31 Create a Device Shortcut to the Controller.

5 33 Create the OB16_Light Indicator .. 34 Create a Push Button .. 38 Test the Indicator and Push Button.. 40 Add a Goto Configuration Mode Button .. 43 Assign Function Keys.. 45 Assign an Initial Screen .. 46 Transfer to PanelView Plus Terminal .. 47 Test the Application on the PanelView Plus Terminal.. 49 Additional Resources .. 50 Index.. 514 Rockwell Automation Publication IASIMP-QS033A-EN-P - March 2012 Table of ContentsNotes:Rockwell Automation Publication IASIMP-QS033A-EN-P - March 20125 PrefaceThis quick start provides examples and procedures for including a PanelView Plus terminal in a Logix5000 Control system over an EtherNet/IP network. The programming examples are not complex, and offer easy solutions to verify that devices are functioning and communicating Using This PublicationYou can only use the tasks described in this publication after first completing some prerequisite tasks with a Logix5000 controller.

6 For example, before you can add a PanelView Plus terminal to an RSLogix 5000 project, as described on page 21, you must first create the project in a Logix5000 b l e 1 describes the tasks you must complete before using this more information on how to complete these tasks with specific Logix5000 controllers, see the Integrated Architecture : Logix5000 Control Systems Quick Starts Quick Reference, publication publication describes basic example tasks you can complete when using a PanelView Plus terminal on an EtherNet/IP network. The tasks described are not the only tasks you can complete with the terminal on an EtherNet/IP example graphics shown in Table 1 - Required Tasks To Complete Before Using This Quick Start on page 6 are for CompactLogix 5370 L3 controllers.

7 Depending on the Logix5000 controller you are using, the specific steps to complete the tasks described in the table might Automation Publication IASIMP-QS033A-EN-P - March 2012 PrefaceTable 1 - Required Tasks To Complete Before Using This Quick StartTaskDescriptionPrepare the Logix5000 Control system hardwareAssemble the Control system and connect to necessary communication networks. Some components, for example, the desired Logix5000 controller and system power supply, are required. Other components, for example, a network communication module, are graphics show the assembly of an example Logix5000 : This task does not include installation of specific hardware components, for example, PanelView Plus terminals, used over the networks included in your the computerInstall necessary software, such as RSLogix 5000 software, on your (Rear)1 (Front)Rockwell Automation Publication IASIMP-QS033A-EN-P - March 20127 PrefaceConfigure the networksComplete required tasks associated with the networks used in your application.

8 For instance, as assign an IP address to the controller or to a communication module in your Logix5000 Control an RSLogix 5000 projectCreate a project to be used with your Logix5000 controller. A project includes all desired Control system components and necessary programming. For example, add ladder logic to test tasks associated with individual system Table 1 - Required Tasks To Complete Before Using This Quick StartTaskDescription8 Rockwell Automation Publication IASIMP-QS033A-EN-P - March 2012 PrefaceOther Logix5000 Control system Quick StartsThis quick start describes how to use one device on one network in a Logix5000 Control system . Typically, though, a Logix5000 Control system includes more than the controller and one device on one example, if a Logix5000 Control system operates on an EtherNet/IP network, in addition to a controller, power supply, and communication modules, the system might use remote I/O modules, drives and HMI quick starts describe how to use different devices on different networks in Logix5000 Control systems.

9 For more information, see the Integrated Architecture: Logix5000 Control Systems Quick Starts Quick Reference, publication Each ChapterThe beginning of each chapter contains the following information. You should read these sections before beginning work in each chapter: Before You Begin - This section lists the tasks you must complete before starting the chapter. What You Need - This section lists the tools that are required to complete the tasks in the chapter. Follow These Steps - This section illustrates the steps in the current Automation Publication IASIMP-QS033A-EN-P - March 20129 PrefaceWhere to StartPrepare the PanelView Plus Terminal Hardwarepage 13 Create a PanelView Plus Applicationpage 21 Prerequisite TasksDescribed in Before Using This Publication on page Prepare the Logix5000 Control system Prepare the Configure the Create an RSLogix 5000 Controller10 Rockwell Automation Publication IASIMP-QS033A-EN-P - March 2012 PrefaceHow Hardware Is ConnectedThis quick start demonstrates the following possible Control SoftwareTo complete examples in this quick start, you need the software described in this for This TaskRSLogix or later(1)(1)

10 RSLogix 5000 software, version or later is required for use of this quick start because the example Logix5000 controller, and associated tasks, described herein are completed in a CompactLogix L3ER Control system . CompactLogix L3ER Control systems require RSLogix 5000 software, version or later. If you connect a PanelView Plus terminal over an EtherNet/IP network in a Logix5000 Control system that uses a different controller, the minimum version may or change RSLogix 5000 projects to use PanelView Plus terminalsFac tor yTalk View Machine Edition(2)(2) When you install the FactoryTalk View Machine Edition software, you automatically install FactoryTalk Services Platform software and RSLinx Enterprise or later(3)(3) You can use version with some Logix5000 controllers.