MODEL S-101 - AMF Reece

1 MODEL S-101 EYELET BUTTONHOLE MACHINEPARTS AND SERVICE MANUAL PART NUMBER 97. is trademark of AMF Group, Registration Card (Please Fax or Mail immediately after installation)Note: All Warranty Claims Void, unless Registration Card on file at AMF Reece HQMachine MODEL number:(S101, S100, S104, S105, S211, Decostitch, S4000 BH,EBS Mark II, etc)Manufacturer s serial or production number:Installation Site Information:Customer s Name:Customer s Mailing Address:Customer s Telephone Number:Supervising Mechanic s or Technician s Name:Signature of Supervising Technician:AMF Reece Technician s Name:AMF Reece Technician s Signature:Type of garment produced at this location?

2 Average Daily Production Expected from this machine?(number of buttonholes, jackets sewn, pants produced, buttons sewn, etc)Any special requirements required at this location?What other AMF Reece Machines are at this location?How can we serve you better?Tov rn 837, 796 25 Prost jov, Czech RepublicFax: +420 582 360 606, e-mail: website: WARRANTY ON NEW AMF Reece EQUIPMENTW arranty provisions:A ninety (90) day limited service labor warranty to correct defects in installation, workmanship, or material without charge forlabor. This portion of the warranty applies to machines sold as installed one (1) year limited material warranty on major component parts to replace materials with defects.

3 Any new part believeddefective must be returned freight prepaid to AMF Reece , Inc. for inspection. If, upon inspection, the part or material is deter-mined to be defective, AMF Reece , Inc. will replace it without charge to the customer for parts or labor warranty period shall begin on the completed installation date. Material warranty shall begin on the date theequipment is shipped from AMF Reece , :Excluded from both service labor warranty and material warranty are: (1) Consumable parts which would be normally consideredreplaceable in day-to-day operations. These include parts such as needles, knives, loopers and spreaders.

4 (2) Normal adjustmentand routine maintenance. This is the sole responsibility of the customer. (3) Cleaning and lubrication of equipment. (4) Partsfound to be altered, broken or damaged due to neglect or improper installation or application. (5) Damage caused by the use ofnon-Genuine AMF Reece parts. (6) Shipping or delivery is no service labor warranty for machines sold as uninstalled .Equipment installed without the assistance of a certified technician (either an AMF Reece Employee, a Certified Contractor, orthat of an Authorized Distributor) will have the limited material warranty only. Only the defective material will be covered.

5 Anycharges associated with the use of an AMF Reece Technician or that of a Distributor to replace the defective part will be thecustomer s OTHER WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, and FITNESS FORA PARTICULAR PURPOSE, OR ANY OTHER MATTER IS GIVEN BY SELLER OR SELLER S AGENT IN CONNECTION HERE-WITH. UNDER NO CIRCUMSTANCES SHALL SELLER OR SELLER S AGENT BE LIABLE FOR LOSS OF PROFITS OR ANYOTHER DIRECT OR INDIRECT COSTS, EXPENSES, LOSSES OR DAMAGES ARISING OUT OF DEFECTS IN OR FAILURE OFTHE EQUIPMENT OR ANY PART TO DO IF THERE IS A QUESTION REGARDING WARRANTYIf a machine is purchased through an authorized AMF Reece , Inc.

6 Distributor, warranty questions should be first directed to thatdistributor. However, the satisfaction and goodwill of our customers are of primary concern to AMF Reece , Inc. In the event thata warranty matter is not handled to your satisfaction, please contact the appropriate AMF Reece office:EuropeProstejov, Czech RepublicPhone:Fax:e-mail:(+420) 582-309-286(+420) website: : +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606 Revised 09/20041-10e-mail: website: : +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606 Revised 09/2004S-1011-11 CONTENTS SHEET FOR INSTALLATION ON Reece INDIVIDUAL T MOTION 101 - SETTING UP 101 - OPERATING THAT DETERMINE THE CHARACTER OF THE BUTTONHOLEN eedle the bite and cutting adjuste the clamp the number of stitches per inch in a or decreasing of number of stitches in the eye independentlyof the ADJUSTMENTS - CORRECTIVE AND MAINTENANCEN eedle bar and race line up the and spreader adjust play in split collar line up and adjust the cutting the clamp operating adjust the trip correct distortion of adjust the roll pressure on

7 Length adjust the rocker arm and stop the stop latch on stitching the trigger setting adjust the timing of the handwheel in relation to rocker shaft adjust handwheel to disengage at the stopping positionof the adjust for friction on worm adjust for friction on main : website: : +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606 Revised 09/20041-12 CONTENTSCUT BEFORE - MACHINE TRIMT hreading thread draw-off and tension pick-up thread draw-off and tension trimmer and thread set the under thread adjust the hold down FOR THE ADJUSTABLE FLY BAR BEFORE ENDGING : ; website: : +420 582 309 146 (Service), +420 582 309 286 (Spare Parts).

8 Fax: +420 582 360 606 Revised 09/2004S-1011-1 DescriptionEyelet Buttonhole Sewing MachineSewing SpeedUp to 1,600 spmStitch Type401 two thread chainstitchStitch Density3 to 16 s/cm (7 to 40 spi)Buttonhole Lenght13 to 32 mm ( 1/2" to 1 1/4")Automatic Cutting LenghtN/AEze Shape (X; Y) mmNo Eye; 2,7 x 4,3 End S ha peflibar, open endStitch Bite2 to 4 mmAutomatic Thread TrimingAF - top thread onlyLubricationSemi - automatic wicking systemElectrical Supply230V, 50/60Hz, 3 Ph400V, 50/60Hz, 3Ph230V, 50/60Hz, 1Ph110V 60Hz 1 PhDimensions (crated)Sewing HeadLenght70 cm (27" 1/2")Width55 cm (21" 1/2")Height75 cm (29 1/2")Weight74 kg (163 lbs)TableLenght114 cm (45")Width 68 cm (27")Height 40 cm (16")Weight 80 kg (176 lbs)Overall DimensionsFloor Plan110 x 60 cm (43" x 24")Table Height70 cm (27 1/2") adjustable to 90 cm (35")EQUIMENT FAMILIARIZATIONYXS-101e-mail: website.

9 +420 582 309 146+ (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606 Revised 09/20041-2 INSTRUCTIONS FOR INSTALLATION ON Reece INDIVIDUAL TABLESP arts and Belting for this installation are contained inthe accessory box which accompanies each Be certain that Motor Pulley rotates in direction ofarrow. If not, motor rotation must be corrected beforeoperating Check with a plumb line to see that the heel ofTransmitter Pedal is 6 in back of front edge of Place the Machine on the Table between the beltslots and even with front edge of Table. Install crossedBelt o and open Belt p. The rear leg of Belt p mustpass between the Idle Pulley q and Belt Guard Adjust Machine sideways as necessary so that Beltp is central in its belt slot, and attach Machine toTable with 4 wood Crank the Machine head to the rearmost point of itstravel and adjust Idle Pulley q, to provideapproximately 1/4 clearance between Belt Guard rand the front leg of Belt Approx 1/4 ne-mail: ; website: : +420 582 309 146 (Service), +420 582 309 286 (Spare Parts).

10 Fax: +420 582 360 606 Revised 09/2004S-1011-3101 Stop Position - all 101 models except the Eyelet and Cross Oval -when the head of the machine is all the way ) Page 16, Figure 5 and 6 - Machine in stop position and the stitchwheel locked up. Check Roll on the It should rest lightly on the Length by turning Adjustment Screw u on ) Page 17, Figure 1A - Machine in stop position - locked up. p should lightly contact the low point of the cam on the insideof the Hand Wheel Adjust by loosening r on Three Forked Lever s. Recheckadjustment number ) Page 18, Figures 4 and 5 - While holding turning pressure onthe Hand Wheel, , crank the machine back by using the Cutting instead of the Crank (On Cut Beforemachines, use the crank until after cutting or remove cutting steel.