Example: tourism industry
O-360 & IO-360 SERIES ENGINES
moving the propeller do the following: • do not stand within the arc of the propeller blades while turning the propeller. • verify all spark plug leads are disconnected. • verify magneto switches are connected to magnetos and that they are in the “off” position and p-leads are grounded. • throttle position “closed”.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
O-360 & IO-360 Series Model Specification Summary
rv7-a.comSuperior Vantage IO-360 Series 26 in-Hg x 2400 RPM-200-150-100-50 0 Below Peak EGT (°F)-75-50-25 0 Below Peak CHT (°F) 80 90 100 110 120 130 140 Corrected Power (Hp) 0.40 0.45 0.50 0.55 0.60 0.65 0.70 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 BSFC (Lb/Hp-hr) Fuel Flow (Lb/Hr)
Related documents
TELEDYNE CONTINENTAL AIRCRAFT ENGINE Category 1 …
www.tcmlink.comTiming Indicator, contact the applicable tool manufacturer for magneto timing instructions. B. GEARED ENGINES . CAUTION: Prior to checking or adjusting engine magneto timing, the aircraft must be situated in a normal attitude on a level surface. If the engine has been removed from the airframe, then the engine must be verified to be level prior to
EVINRUDE AND JOHNSON 5 AND 6 HP (1965-1968)
islandersailboat.infoOM4-6 and a timing test light. Any test light or meter which indicates an open and closed circuit is satisfactory. To adjust the points using the special tools, disconnect condenser and magneto coil leads from both points and install the timing fixture (TF—Fig. OMi4-6) over crank-shaft and flywheel key. Tum crankshaft
Homelite XL Chainsaw Owners Manual 24904
www.leonschainsawpartsandrepair.comMagneto: Conventional Breaker Point Magneto System. Ignition Timing: 230 BTDC . Keep a fire extinguisher handy. For 15 minutes after stopping be sure there are no smoldering fires and report them, listing ca proper authorities. Study this manual to learn the b' use your chain saw.
John Deere A and B tractors - classicvehicledata.com
www.classicvehicledata.comThe ignition system is by a magneto, usually made by Wyco, most are fitted with a stop switch, though in ... When refitting the shaft, line up timing marks on camshaft gears, refit bearing assembly and flywheel distance piece with slotted face outwards, fit bearing cover so that there is a clearance all round the distance ...
Three-Axis Digital Compass IC HMC5883L
www.farnell.comart, high-resolution HMC118X series magneto-resistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I2C serial bus allows for easy interface. The HMC5883L is a 3.0x3.0x0.9mm surface
3 to 10 HP 4-Cycle L-Head Engines - Allotment & Gardens
www.allotment-garden.orgNOTE: DO NOT USE SAE10W40 OIL. For summer (above 32°F, 0oC) use SAE 30 oil part # 730225 (1 quart, .946 liter container) in high temperature, high load applications. S.A.E.10W30 is an acceptable substitute. For winter (below 32°F, 0oC) use S.A.E. 5W30 oil part # 730226 (1 quart, .946 liter container) S.A.E.10W is an acceptable substitute.