OLED-128O064D-BPP3N00000 - Vishay Intertechnology

1 Revision: 14-Dec-161 Document Number: 37902 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT x 64 Graphic OLEDFEATURES Type: graphic Display format: 128 x 64 dots Built-in controller: SSD1306BZ Duty cycle: 1/64 +3 V power supply Interface: 6800, 8080, serial, and I2C Material categorization: for definitions of compliance please see Notes(1)All the above voltages are on the basis of VSS = 0 V.

2 (2)When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to section 6 Electrical Characteristics . If this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may DATAITEMSTANDARD VALUEUNITM odule x x x x x x holen/aABSOLUTE MAXIMUM RATINGSITEMSYMBOLSTANDARD voltage for logic (1)(2)VDD04 VSupply voltage for display (1)(2)

3 VCC015 Operating temperatureTOP-40+80 CStorage temperatureTSTG-40+80 ELECTRICAL CHARACTERISTICSITEMSYMBOLCONDITIONSTANDA RD voltage for voltage for displayVCC-101215 Input high VDD-VDDI/OInput low VDDO utput high VDD-VDDI/OOutput low VDD50 % check board operating currentICCVCC = 12 V91012mAOPTIONSEMITTING Revision: 14-Dec-162 Document Number: 37902 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT PIN FUNCTIONPIN NO.

4 SYMBOLFUNCTION1NC (GND)Reserved pin (supporting pin)The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external terminal of the flying inverting capacitor negative terminal of the flying boost capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not supply for DC/DC converter circuitThis is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used.

5 It should be connected to VDD when the converter is not of logic circuitThis is a ground pin. It also acts as a reference for the logic pins. It must be connected to external supply for logic circuit. This is a voltage supply pin. It must be connected to external protocol select These pins are MCU interface selection input. See the following table:11BS1I2C3-wire SPI4-wire SPI8-bit 68XX parallel8-bit 80XX parallelBS0010 0 012BS2BS1100 0 1BS2000 1 113CS#Chip selectThis pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled #Power reset for controller and driverThis pin is reset signal input.

6 When the pin is low, initialization of the chip is #Data / command controlThis pin is data / command control pin. When the pin is pulled high, the input at D7 to D0 is treated as display data. When the pin is pulled low, the input at D7 to D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the timing characteristics diagrams. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register.

7 In I2C mode, this pin acts as SA0 for slave address #Read / write select or write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as read / write (R/W#) selection input. Pull this pin to high for read mode and pull it to low for write 80XX interface mode is selected, this pin will be the write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled #Read / write enable or readThis pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the enable (E) signal.

8 Read / write operation is initiated when this pin is pulled high and the CS# is pulled connecting to an 80XX-microprocessor, this pin receives the read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled to 25D0 to D7 Host data input / output busThese pins are 8-bit bi-directional data bus to be connected to the microprocessor s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 and D1 should be tired together and serve as SDAout and SDAin in application and D0 is the serial clock input reference for brightness adjustmentThis pin is segment current reference pin.

9 A resistor should be connected between this pin and VSS. Set the current lower than output high level for COM signalThis pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and supply for OEL panelThis is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not of analog circuitThis is an analog ground pin.

10 It should be connected to VSS (GND)Reserved pin (supporting pin)The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external Revision: 14-Dec-163 Document Number: 37902 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT in millimetersThe non-specified tolerance of dimension is 63(row 1)Common 32(row 63)Segment 127(column 1)Common 0(row 64)Segment 0(column 128)Common 31 (row 2) : 20 (VA) ( ) (alignment mark) x (AA) (AA) area "128 x 64 pixels x (30 - 1) = ( ) ( ) (VA) (polarizer) (polarizer) sideContact sideRemove tapeGluePolarizerShading Revision.