Operation OManual - SMC株式会社

1 Pressure SettingSet ON and OFF point of the Pressure the pressure exceeds the set value, thePressure switch will turn the pressure falls below the set value bythe amount of hysteresis or more, thePressure switch will turn default setting of the output setvalue is the central value between theatmospheric pressure and the upperlimit of the rated pressure this condition, shown to theright, is acceptable, then keepthese settings.<How to operate>[Hysteresis mode]1. Press the button once in measurement [P_1] or [n_1] and the set value aredisplayed in / DisconnectingWhen mounting the connector, insert it straight into the socket, holding thelever and connector body, and push the connector until the lever hooks intothe housing, and removing the connector, press down the lever to release the hookfrom the housing and pull the connector straight Pressure SwitchOperation ManualZSE30A(F)/ISE30 AThank you for purchasing an SMC ZSE30A(F)/ISE30A Series Digital read this manual carefully before operating the product and make sure youunderstand its capabilities and keep this manual handy for future obtain more detailed information about operating this product, pleaserefer to the SMC website (URL )

2 Or contact InstructionsThese safety instructions are intended to prevent hazardous situations and/orequipment instructions indicate the level of potential hazard with the labels of"Caution", "Warning" or "Danger". They are all important notes for safety and mustbe followed in addition to International standards (ISO/IEC) and other SettingDefault settingAt the time of shipment, the following settings are the setting is acceptable, keep it for to the SMC website (URL ) for more detailedinformation about setting changes, or contact SMC.[F 0] Unit conversion function[F 1] Setting of OUT1[F 2] Setting of OUT2 Same setting as [F 1] display colour is linked to the setting of OUT1, and can not be set parameter settingItemDefault setting[F 3] Setting of response ms[F 4] Setting of display resolution1000-split[F 5] Setting of auto-presetManual0%[F 6] Setting of fine adjustment of display valueOFF[F 7] Setting of power saving modeOFF[F 8] Setting of security codeOFF[F90] Setting of all functionsOFF[F97] Selection of copy functionNormal[F98] Check of outputOFF[F99]

3 Reset to the default settingItemDescriptionOutput modeSelects hysteresis mode or window comparator outputSelects reversed settingSets ON or OFF point of the switch settingHysteresisChattering can be prevented by setting modeISE30A: MPaZSE30A: kPaZSE30AF: kPaNormal outputISE30A: MPaZSE30A: kPaZSE30AF: kPaUnit specificationModelNil or MISE30 AZSE30A(F)Default settingPISE30 AMPakPaZSE30A(F)Measurement modeThe measurement mode is the condition wherethe pressure is detected and indicated, and theswitch function is is the basic mode, and the other modesshould be selected for setting changes andother function mode1 s1 s1 sDisplay to show the unit specificationDisplay to show the productThe power is supplied1 sDisplay to show the standard productDisplay to show the pressure rangeIndication LED (Green OUT1 and Red OUT2): Displays the switch display: Displays the current status of pressure, setting mode, selectedindication unit and error code.

4 Four display modes can beselected: display always in red or green, or display changing fromgreen to red, or red to green, according to the output (UP): Selects the mode or increases the ON/OFF set this button to change to the peak display (DOWN): Selects the mode or decreases the ON/OFF set this button to change to the bottom display (SET): Press this button to change to another mode and to set a indication: Displays the unit currently selected (only for kPa or MPa unitindication).Summary of Product partsInstallationMounting with bracket : The tightening torque of the piping port must be 7 to 9 tightening torque of the mounting screw for the bracket must be to the bracket to the pressure switch with the set screws M3x5L (2 pcs.)supplied, before installation.

5 Bracket A (Model: ZS-38-A1)Bracket B (Model: ZS-38-A2)Bracket C (Model: ZS-38-A3)Mounting and InstallationNames of individual partsConnector pin numberspsiLCD displayIndication LEDbutton (UP)button (SET)button (DOWN)Unit indicationM3x5 LBracket BM3x5 LBracket AM3x5 LM3x5 LM3x5 LBracket CM3x5 LDC(+) Brown 5 Pin Black 4 OUT2 White 3(FUNC) 2DC(-) Blue 1 HousingPinsLeverLead wire (Brown)ConnectorLead wire (Blue)Displays in turnNormal outputReversed outputDisplay colourSelects the display : GreenOFF: RedCAUTION indicates a hazard with a low level of riskwhich, if not avoided, could result in minor ormoderate Operation manual is intended for those who have knowledge of machineryusing pneumatic equipment, and have sufficient knowledge of assembly, Operation and maintenance of such equipment.

6 Only those persons areallowed to perform assembly, Operation and and understand this Operation manual carefully before assembling,operating or providing maintenance to the :Warning:Danger:WARNING indicates a hazard with a medium level ofrisk which, if not avoided, could result in death orserious indicates a hazard with a high level of riskwhich, if not avoided, will result in death or InstructionsDo not disassemble, modify (including changing the printed circuit board) or injury or failure can not operate in an atmosphere containing flammable or explosive or an explosion can product is not designed to be explosion not use the product in a place where static electricity is a it can cause failure or malfunction of the The direct current power supply to be used should be UL approved as follows:Circuit (of Class2) which is of maximum 30 Vrms ( V peak), with UL1310 Class2 power supply unit or UL1585 Class2 transformer.

7 The product is a approved product only if it has a mark on the using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operationOtherwise malfunction can result, causing an following instructions must be followed during maintenance: Turn off the power supply Stop the air supply, exhaust the residual pressure and verify that the air is released before performingmaintenance workOtherwise an injury can maintenance is complete, perform appropriate functional inspections and leak Operation if the equipment does not function properly or there is a leakage of leakage occurs from parts other than the piping, the product might be the power supply and stop the fluid not apply fluid under leaking cannot be assured in the case of unexpected not touch the terminals and connectors while the power is electric shock, malfunction or damage to the product can not operate the product outside of the not use for flammable or harmful , malfunction.

8 Or damage to the product can the specifications before Pressure switch operates within a set pressure range (from P1L to P1H)during window comparator mode. Set P1L (switch lower limit) and P1H (switchupper limit) with the setting procedure above. (When reversed output isselected, [n1L] and [n1H] are displayed.)Zero clear of displayThe display is reset to zero when the and buttons are pressedsimultaneously for 1 the initial Operation , always perform zero clear with no pressure SettingsPeak / Bottom hold displayZero clearKey lockTo set each of these functions, refer to the SMC website(URL ) for more detailed information, or contact to reset the product after a power cut or forcible de-energizingThe setting of the product will be retained as it was before a power cut output condition is also basically recovered to that before a power cut orde-energizing, but may change depending on the operating , check the safety of the whole installation before operating the product.

9 Ifthe installation is using accurate control, wait until the product has warmed up(approximately 10 to 15 minutes).TroubleshootingThe switch output load current is morethan 80 the power off and remove thecause of the over current. Thenturn the power IndicationThis function is to display error location and content when a problem or an ErrorDuring the zero clear Operation ,pressure above 7% ( compound pressure) has beenapplied. After 1 second, the mode willreturn to measurement mode. The zeroclear range can vary 1% withindividual product zero clear Operation againafter restoring the applied pressureto an atmospheric has exceeded the upper limitof the set pressure in the case of an internaldata applied pressure to a levelwithin the set pressure the power off and turn it resetting fails, an investigation bySMC Corporation will be the error can not be reset after the above measures are taken, then pleasecontact : Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.

10 2011 SMC Corporation All Rights ReservedPressure has exceeded the lower limitof the set pressure UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPANP hone: +81 3-5207-8249 Fax: +81 3-5298-5362 URL NameError DisplayError TypeTroubleshooting MethodOver currentError3. Press the or button to change the set button is to increase and the button isto the button once to increase by onedigit, and press it continuously to keep increasingthe set the button once to decrease by onedigit, and press it continuously to keep decreasingthe set Press the button to complete the models with 2 outputs, [P_2] or [n_2] will be displayed. Set as selection modeIn measurement mode, press the button for 2 seconds or longerto display [F 0].