OPERATOR'S MANUAL

1 operator 'SMANUALM odel C713 Soft Serve FreezerOriginal Operating Instructions062180-M2/11/05 (Original Publication)(Updated 8/3/15)Complete this page for quick reference when service is required:Taylor Distributor:Address:Phone:Service:Parts: Date of Installation:Information found on the data label:Model Number:Serial Number:Electrical Specs: VoltageCyclePhaseMaximum Fuse Size:AMinimum Wire Ampacity:AE2005 Carrier Commercial Refrigeration, MAny unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this workmay be a violation of Copyright Law of the United States of America and other countries, could result in theawarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in furthercivil and criminal penalties.

2 All rights Companya division of Carrier Commercial Refrigeration, N. Blackhawk , IL 61072 Table of ContentsModel C713 Table of ContentsSection 1To the Cooled Connections (Water Cooled Units Only) 2To the 4 operator Parts C713 Door and Beater 5 Important: To the Screen 's 6 Operating Cylinder Brush Product From The Freezing C713 Table of ContentsTable of Contents - Page 7 Important: operator Cleaning and Bacterial Maintenance 8 Troubleshooting 9 Parts Replacement 10 Limited Warranty on 11 Limited Warranty on.

3 Continuing research results in steady improvements; therefore, informationin this MANUAL is subject to change without : Only instructions originating from the factory or its authorized translationrepresentative(s) are considered to be the original set of Carrier Commercial Refrigeration, Inc.(Original Publication)(Updated August, 2015)062180- MAny unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this workmay be a violation of Copyright Law of the United States of America and other countries, could result in theawarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in furthercivil and criminal penalties.

4 All rights Companya division of Carrier Commercial Refrigeration, N. Blackhawk , IL 610721 Model C713To the Installer131121 Section 1To the InstallerThe following information has been included in themanual as safety and regulatory guidelines. Forcomplete installation instructions, please see theInstallation SafetyIn all areas of the world, equipment shouldbe installed in accordance with existing local contact your local authorities if you have should be taken to ensure that all basic safetypractices are followed during the installation andservicing activities related to the installation andservice of Taylor authorized Taylor service personnelshould perform installation and repairs onthe service personnel should consultOSHA Standard or theapplicable code of the local area for theindustry standards on lockout/tagoutprocedures before beginning any

5 Installationor service personnel must ensurethat the proper PPE is available and wornwhen required during installation service personnel must removeall metal jewelry, rings, and watches beforeworking on electrical main power supply(s) to the freezermust be disconnected prior to performing anyrepairs. Failure to follow this instruction may result inpersonal injury or death from electrical shock orhazardous moving parts as well as poorperformance or damage to the :Allrepairsmustbeperformedbyanauthorized Taylor Service unit has many sharp edges that cancause severe PreparationReview the area the unit is to be installed in beforeuncrating the unit making sure that all possiblehazards the user or equipment may come into havebeen Cooled UnitsThe Model C713 air cooled unit requires a minimumof 3 (76 mm) of clearance on all sides.

6 Install thedeflector provided to prevent recirculation of warmair. This will allow for adequate air flow across thecondenser. Failure to allow adequate clearance canreduce the refrigeration capacity of the freezer andpossibly cause permanent damage to Indoor Use Only:This unit is designed tooperate indoors, under normal ambienttemperatures of 70_-75_F(21_-24_C). The freezerhas successfully performed in high ambienttemperatures of 104_(40_C) at reduced unit mustNOTbeinstalledinanareawhere a water jet or hose can be water jet or hose to rinse or clean the unit.

7 Failureto follow this instruction may result in unit must be installed on a level surfaceto avoid the hazard of tipping. Extreme care shouldbe taken in moving this equipment for any or more persons are required to safely movethis unit. Failure to comply may result in personalinjury or equipment the unit and inspect it for damage. Reportany damage to your Taylor piece of equipment is made in the USA and hasUSA sizes of hardware. All metric conversions areapproximate and vary in C713To the Installer130318 Water Connections(Water Cooled Units Only)An adequate cold water supply must be providedwith a hand shut-off valve.

8 On the underside of thebase pan or on the right side, two 3/8 waterconnections for inlet and outlet are provided for easyhook-up. 1/2 inside diameter water lines should beconnected to the machine. (Flexible lines arerecommended, if local codes permit.) Depending onlocal water conditions, it may be advisable to installa water strainer to prevent foreign substances fromclogging the automatic water valve. There will beonly one water in and one water out NOT install a hand shut-off valve on the water out line! Water should always flow in this order:first, through the automatic water valve; second,through the condenser; and third, through the outletfitting to back flow prevention device isrequired on the incoming water connection refer to the applicable National, State, andlocal codes for determining the proper ConnectionsIn the United States, this equipment is intended tobe installed in accordance with the NationalElectrical Code (NEC), ANSI/NFPA 70-1987.

9 Thepurpose of the NEC code is the practicalsafeguarding of persons and property from hazardsarising from the use of electricity. This code containsprovisions considered necessary for safety. In allother areas of the world, equipment should beinstalled in accordance with the existing local contact your local YOUR LOCAL ELECTRICAL CODES!Each unit requires one power supply for each datalabel on the unit. Check the data label(s) on thefreezer for branch circuit overcurrent protection orfuse, circuit ampacity, and other electricalspecifications.

10 Refer to the wiring diagram providedinside of the electrical box for proper : THIS EQUIPMENT MUST BEPROPERLY GROUNDED! FAILURE TO DO SOCAN RESULT IN SEVERE PERSONAL INJURYFROM ELECTRICAL SHOCK!DO NOT operate this freezer with largerfuses than specified on the unit data label. Failure tofollow this instruction may result in electrocution ordamage to the unit is provided with an equipotentialgrounding lug that is to be properly attached to therear of the frame by the authorized installer. Theinstallation location is marked by the equipotentialbonding symbol (5021 of IEC 60417-1)