Operator’s Manual - OPTI Medical Systems

1 OPTI CCA-TS2 AnalyzerOperator s Manual operator S Manual REVISION LOG(Please record any changes made to this Manual )Proprietary Rights Notice Information in this document is subject to change without notice. Companies, names and data used in examples are fictitious unless otherwise noted. No part of this document may be reproduced or transmitted in any form or by any means, electronic, mechanical or otherwise, for any purpose, without the express written permission of OPTI Medical Systems , Inc. OPTI Medical Systems , Inc. may have patents or pending patent applications, trademarks, copyrights or other intellectual or industrial property rights covering this document or subject matter in this document.

2 The furnishing of this document does not give a license to these property rights except as expressly provided in any written license agreement from OPTI Medical Systems . 2013 OPTI Medical Systems , Inc. All rights reserved. OPTI, the OPTI Medical logo, and ComfortSampler are trademarks or registered trademarks of OPTI Medical Systems , Inc. in the United States and/or other countries. Other trademarks are the property of their respective in Medical Systems , Inc. 235 Hembree Park Drive Roswell, GA 30076 USA REV A RevisionRelease DateApproved byDescriptionAMarch 2013per PCR120182 Important Information! Important Information!

3 This operator s Manual contains important warnings and safety information to be observed by the user. This instrument is only intended for one area of application which is described in the instructions. The most important prerequisites for application, operation and safety are explained to ensure smooth operation. No warranty or liability claims will be covered if the instrument is applied in areas other than those described or if the necessary prerequisites and safety measures are not instrument is only to be operated by qualified personnel capable of observing these accessories and supplies either delivered by or approved by OPTI Medical Systems are to be used with the instrument.

4 Due to this instrument s operating principle, analytical accuracy not only depends on correct operation and function, but also upon a variety of external influences beyond the manufacturer s control. Therefore, the test results from this instrument must be carefully examined by an expert, before further measures are taken based on the analytical should never be administered based on results that are flagged on the adjustment and maintenance with removed covers and connected power mains are to be performed only by a qualified technician who is aware of the dangers involved. Instrument repairs are to be performed only by the manufacturer or qualified service Information!

5 Important Information!Operating Safety InformationOperating Safety Information Overvoltage Category II when connected to a branch circuit. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Caution: The instrument is designed as a conventional device (closed, not waterproof type). Do not operate the instrument in an explosive environment or in the vicinity of explosive anesthetic mixtures containing oxygen or nitrous oxide. This instrument is suitable for continuous operation. The power plug is to be plugged into a ground socket only.

6 When using an extension cord, make sure that it is of the proper size and is properly grounded. Any breakage of the ground lead inside or outside the instrument or a loose ground connection can cause a hazardous condition when operating the instrument. Intentional disconnection of the grounding is not permitted. When replacing the fuses, make sure that they are of the same type and rating as the original fuses. Never use repaired fuses or short-circuit the fuse device is a Class 1 Laser product according to the requirements of IEC 60825-1. The LEDs have been certified as an EXEMPT RISK GROUP in compliance with IEC maximum energy output is as follows:670 nm (LED): 40 Microwatts max.

7 For 400ms780 nm (Laser): 40 Microwatts max. for 400ms850 nm (Laser): 40 Microwatts max. for 400msCaution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation of Acceptability:Coin cell battery on main board: Overcharging, short circuiting, reverse charging, mutilation or incineration of the cells must be avoided to prevent one or more of the following occurrences: release of toxic materials, release of hydrogen and/or oxygen gas, rise in surface temperature. If a cell has leaked or vented, it should be replaced immediately using protective gloves.

8 If and when necessary, these cells must be replaced with identical new ones from the same manufacturer. If a cell to be replaced is connected with other cells in series, it is recommended that the other cells be replaced with new ones at the same time. Reverse polarity installation of the cell in the end product must be avoided. Operating Safety InformationOperating Safety InformationRecommendations for Usage and Storage of Lithium Ion Battery Pack:a) Do not dismantle, open or shred secondary cells or ) Do not expose cells or batteries to heat or fire. Avoid storage in direct ) Do not short-circuit a cell or a battery.

9 Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal ) Do not remove a cell or battery from its original packaging until required for ) Do not subject cells or batteries to mechanical shock. f) In the event of cell leaking, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek Medical ) Do not use any charger other than that specifically provided for use with the ) Observe the plus (+) and minus (-) marks on the cell, battery and equipment and ensure correct ) Do not use any cell or battery which is not designed for use with the ) Do not mix cells of different manufacture, capacity, size or type within a ) Keep cells and batteries out of reach of ) Seek Medical advice immediately if a cell or a battery has been ) Always purchase the correct cell or battery for the ) Keep cells and batteries clean and )

10 Wipe the cell or battery terminals with a clean dry cloth if they become ) Secondary cells and batteries need to be charged before use. Always use the correct charger and refer to the manufacturer s instructions or equipment Manual for proper charging ) Do not leave a battery on prolonged charge when not in ) After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum ) Secondary cells and batteries give their best performance when they are operated at normal room temperature (20 C 5 C).t) Retain the original product literature for future ) Use cell and battery only in the application for which it was ) When possible, remove the battery from the equipment when not in ) Dispose of cells and batteries DefinitionsThe symbols described below are used on the packaging of OPTI CCA-TS2 related ExplanationAttention Symbol Refer to the operator s Manual or Service Manual for further instructions.