Owner's Guide - Trane

1 Owner's GuideIndoor Units:Air HandlersGas Furnaces32-5064-WEB01 2 32-5064-WEB01 Proper Maintenance Air HandlersHow to remove the filter from your Air your dealer where the filter is located when your system is installed. It may be behind the bottom panel of your indoor unit. Or it may be at the top, bottom, or either side. Or there may be two any case, removing a filter is easy. Just make sure you insert the clean filter with the arrows on it pointing in the direction of the airflow. Your installing dealer is your best source of filter and maintenance prevent injury or death, or property damage, read and follow all instructions and warnings, including labels shipped with or attached to unit before operating your new air conditioning heating system is not operational during the cold weather months, provisions must be taken to prevent freeze-up of all water pipes and water receptacles.

2 This is very important during times of special care has been taken to minimize sharp edges in the construction of the unit, be extremely careful when handling parts or reaching into the installation, adjustment, alteration, service maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause personal injury or property damage. Consult a qualified installer or service agency for information or assistance. The qualified installer or agency must use factory-authorized kits or accessories when modifying this all electric power to the indoor air handler or furnace before removing access panels to perform any maintenance. Disconnect power to both the indoor and outdoor clean filter saves ensure top efficiency by cleaning the filter the unit circulates and filters the air in your home, dust and dirt particles collect on the filter located in your indoor unit. Excessive buildup forces the system to run longer to maintain your set temperature.

3 And you end up paying for t waste money heating and cooling when you don t need you re going to be away from home for a few days or when outdoor temperatures are moderate don t let your system run unnecessarily. Lower the thermostat to 55 F in the winter. And raise it to 85 F in summer. Then when you return or when temperatures dictate you can reset the system and it will immediately begin making your home comfortable again. Continuous fan mode during cooling operation may not be appropriate in humid climates. If the indoor air exceeds 60% relative humidity or simply feels uncomfortably humid, it is recommended that the fan only be used in the AUTO stop the system by shutting off the main the main power is ever disconnected for more than three hours, turn off the thermostat. Then wait for at least three more hours after the power has been restored before turning the thermostat back on. Failure to follow this procedure could result in damage to your or replace your filter at least once a month or twice a month when the system is running you have a semi-permanent filter, you can take the filter out of the frame and vacuum it.

4 Where disposable filters are used, they must be replaced every month with the same size as originally supplied. Both methods are quick and easy and guaranteed to cut the energy used by your system. When replacing your air handler filters, always use the same size and type that was originally supplied. Filters are available from your operating costs by keeping snow, ice and debris clear of your outdoor heat pump : Condensation may occur on the surface of the air handler when installed in an unconditioned operation of your outdoor unit requires the free flow of air over the coils. Anything that blocks this flow forces the unit to work harder to do its job. At no time should anything be stacked against the side of the outdoor unit or draped over it. Keeping it clear of debris helps it work at peak efficiency, and that helps hold down operating access door marked "FILTER" and lift up the open side of the dirty filter out, replace with a new filter making sure the arrows printed on it are pointing in the direction of the "FILTER" door firmly in place and snap the levers down (closed).

5 Your filter may or may not be regular dealer maintenance please refer to 3 32-5064-WEB01 Before you call for service, check the following:ProblemPossible causePossible RemedyInsufficient heating or cooling1. Dirty filters2. Air not circulating freely3. Blocked outdoor coil1. Clean or replace2. Check supply registers and return grills for blockage3. Clear away leaves or other debrisFailure to operate1. Power off2. Open circuit breaker or burned out fuses3. Improperly adjusted thermostat1. Make sure main switch is in on position2. Reset circuit breaker, or replace burned out fuses3. Check setting, adjust thermostatUnusual NoiseCall your local servicerThe Problem Solver Air HandlersNOTE: Improperly sized vents can cause the formation of condensate, combustion gas leakage and spillage, and an inoperable unit is not a household appliance.

6 It is a complex self-contained system that requires professional maintenance and repair. That s why attempts at do it yourself repairs on an in-warranty unit may void the remainder of your warranty. Other than performing the simple maintenance recommended in this manual, you should not attempt to make any adjustments to your : The blower motor bearings are factory lubricated and under normal operating conditions usually do not require servicing. Your local servicer can advise you if oiling is required. Your dealer should be able to take care of any questions or problems you may your unit looking like new for the enamel finish of your unit with ordinary soap and water. For stubborn grease spots, use a household detergent. Lacquer thinner or other synthetic solvents may damage the set the temperature you temperatures by using the indicators on the thermostat* control. After that, your comfort control center (thermostat) will maintain a constant indoor temperature, regardless of changes in outdoor temperatures.

7 Read your thermostat manual for directions on setting the energy with an electronic programmable an electronic programmable thermostat* energy savings is easy. Just program the thermostat for the temperatures you are most comfortable with and it will automatically change settings up to four times a day. Special weekend and vacation schedules are also easily programmed for comfort and savings. Read your thermostat manual for programming instructions. If you want the optimum balance between comfort and the cost of running your system, we recommend keeping the temperature settings at 68 F for heating and 78 F for energy by letting the thermostat do its job. Once you set the thermostat, keep subsequent adjustments to a minimum. Adjust it only when a new program is needed.*Optional accessoryWhenever your house is to be vacant, arrange to have someone inspect your house for proper temperature. This is very important in below freezing weather. If for any reason your unit should fail to operate, damage could result, such as frozen water pipes.

8 Subject to the terms and conditions of this limited warranty, Trane , Inc. ( Company ) extends a limited warranty against manufacturing defects for the product(s) identified in Table 1 attached hereto ( Products ) that are installed in a residential application (personal, family or household purposes) under normal use and maintenance in the United States and Canada. This limited warranty applies to Products manufactured on or after August 1, order to maximize the available benefits under this limited warranty, the Purchaser (as defined below) should read it in its entirety. All repairs of Product parts covered under this limited warranty must be made with authorized service parts and by a licensed HVAC service provider. Additionally, commercial applications are treated differently under this limited warranty as stated in Table 1 attached hereto. For purposes of this limited warranty, commercial applications shall mean any application other than for personal, family, or household : The limited warranty period for Products is as stated in Table 1 attached hereto.

9 If the Pur-chaser properly registers the Products, the limited warranty period shall be extended as stated in Table 1 attached hereto. Regardless of registration, the Commencement Date for a limited warranty period shall be the date that the original installation is complete and all Product start-up procedures have been prop-erly completed and verified by an installer s invoice. If the installation and start-up date cannot be verified by the installer s invoice, the Commencement Date shall be sixty (60) days after the factory manufacture date which is verified by the Product serial number. Where a Product is installed in a newly constructed home, the Commencement Date is the date the Purchaser purchased the residence from the builder. Proof of Product purchase, installation, and/or closing date of the residence may be required to confirm the Commencement Date. The installation of Product replacement parts under this limited warranty shall not extend the original warranty period.

10 The warranty period for any Product part replaced under this limited warranty is the ap-plicable warranty period remaining under the original Product warranty. WHO IS COVERED: This limited warranty is provided only to the original owner and his or her spouse ( Purchaser ) of the residence where the Products are originally installed. This warranty is not transferable except according to terms stated on the applicable website identified below under Registra-tion Requirements. Company has the right to request any and all proof of Product purchase or installation and/or closing date of the COMPANY WILL DO: Company may request proof of Product purchase and/or installa-tion in order to provide Product parts under this limited warranty. As Company s only responsibility and Purchaser s only remedy under this limited warranty, Company will furnish a replacement part to the licensed HVAC service provider, without charge for the part only, to replace any Product part that fails due to a manufacturing defect under normal use and maintenance.