OWNERS MANUAL - Splendide

1 Corporate offices Westland Sales / PO Box 427 / 15650 SE 102nd Ave / Clackamas, OR 97015 - USA warehouses Clackamas, OR & Elkhart, IN / phone / fax web / / e-mail OWNERS MANUAL When Technology Meets Ecology CAUTION: Before operating this appliance it is recommended that you read this MANUAL and follow all Safety Rules and Operating Instructions. COMBINATION WASHER & VENTED DRYER MODEL WD802M TABLE OF CONTENTS Record Serial & Model 1 Line Drawing and 8 2 How To 9 Removing Shipping 2 Operating 9 2 Your First 9 2 9 3-4 How To Use Your 10 4 Tumble 10 Important Safety 4 To Rinse, Spin and 10 Recessed, Closet and Alcove Installation. 5 Wash 10 Laundry 6 Laundry 11 6 Detergent 11 6 11 6 Liquid Fabrics 11 6 Stain Removal 11-12 Laundry 6 Care and 13 Washer 7 Cleaning the 13 On-Off 7 Cleaning the 13 Medium/High Spin 7 General 13 High/Heat Half/Heat 7 Cleaning the Drain 13 Wash 7 13 Water Cycle 7 Avoid-Service Check List.

2 13-14 Drying 7 Cool Drying 7 Drain 7 Detergent 7 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICES PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "Dangerous Voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-tant operating and maintenance (servicing) instructions in the literature accompanying the appliance. The model number of this product may be found on the back of the unit; and the serial number on the label affixed to the back of the unit. You should note the model and serial numbers of this unit in the space provided, and retain this booklet as a permanent record of your purchase to aid in identification in the event of theft.

3 MODEL NUMBER_____ SERIAL NUMBER_____ WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The washer must be installed on a strong level floor, and in a protected, dry, and well-ventilated area close to a power and water supply of sufficient capacity, and a suffi-cient drain outlet. Dryer installation and grounding should be done in accordance with local codes by a qualified installer. USE AND CARE OF YOUR AUTOMATIC WASHER-DRYER TO AVOID UNNECESSARY SERVICE CALLS Your new appliance is a carefully engineered product. Many times what appears to be a reason to call for service, requires nothing more than a simple adjustment you can easily make in your own home. You will be charged for a service call while the appliance is in warranty if the problem is not caused by defective product workmanship or materials covered by this warranty.

4 To avoid a charge for an unnecessary service call, and before calling a serviceman, please refer to the Avoid Service Check List for situations that you can remedy. This list is included at the back of this Use and Care Book. This appliance is an automatic washer-dryer. It is front loading, with an extra large door opening for easier access. It has 5 wash cycles in addition to extra rinse and extra spin cycles. You will obviously want to obtain the best possible wash. By reading and following the instructions in this booklet you will achieve excellent results. Please ensure that the instructions are followed. If you should need any further advice or assistance please contact the dealer where your machine was purchased. "Installation Instructions" are included in your Use and Care MANUAL for the installers reference. The washer should be plugged into a properly grounded three (3) prong electrical outlet of 115 Volt, 1300W, A, 60 Hertz.

5 It should not be controlled by a wall switch or pull cord which might be turned off accidentally. BEFORE USING WASHER-DRYER Page 1 REMOVE SHIPPING BRACKETS back panel screws and lift panel clear (Fig. 1, Item. A). fixing screws from the four brackets and cross bearing (Fig. 2, Item Y) then remove brackets. back panel with 3 screws previously removed (Fig. 1, Item A). the 4 holes on the cabinet with the plastic blanking plugs that you will find in the accessories bag (Fig. 2, Item X & Z). Leveling After selecting a permanent location, the machine should be properly leveled to prevent vibration. To do this, adjust one or both front levelers, as needed, after loosening the lock nuts. Once your washer is perfectly leveled, be sure to tighten the lock nuts (Fig. 3). GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

6 This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Page 2 FOR YOUR OWN PROTECTION, AND TO PREVENT ACCIDENTS, INJURY AND FIRE, PLEASE READ THE FOLLOWING CAREFULLY: Destroy the carton and plastic bags after the washer-dryer has been unpacked. Children should never be left alone or unattended in the area where appliances are located.

7 Washer installation and grounding must be done in accordance with local codes by a qualified installer. Installation instructions are included in this MANUAL for the installer's reference. Use only low sudsing detergents suitable for front loading washers, or a small amount of regular deter-gent. The soap suds should never exceed the mid-line of the port-hole. The washer must be plugged into a properly grounded three (3) prong electrical outlet. For your safety, the third or round grounding prong must never be removed. DO NOT USE AN EXTENSION CORD. Repair or replacement of a part should be made only by a qualified service technician to prevent personal injury or damage to the machine. Ask your dealer for a list of authorized repair service companies. Disconnect power to the washer at the circuit breaker or fuse box, or unplug the machine in an emergency, or when servicing is required. Have the installer show you and label the proper switch or fuse at the electrical disconnect box.

8 WARNING - The Appliance Should Be Connected To An Individual Branch Circuit With No. 14 AWG Wire And Protected By 15 A Fuse or Breaker. IMPORTANT In the accessories bag you will also find a spanner that is to be used for removing brackets and leveling washer-dryer feet. PLUMBING (Water Inlet) The straight end of these hoses should be connected to the supply (Fig. 4). The 90 angled end of these hoses should be connected to the inlet valves on the back of the machine, using one of the washers to make a water tight seal on each connection. The couplings should be tightened by hand, a tool should only be used if a leak occurs. Do not use excessive force (see M, Fig. 5). The Inlet valves are color-coded: Red = Hot White = Cold It is possible to run the machine on cold water only, but a water supply must be connected to each inlet valve. To do this we suggest you use "F" connector, supplied with the washer-dryer (see N, Fig. 6). PLUMBING (Water Outlet) You should carefully position the drain hose to avoid kinks and ensure proper drainage of the water.

9 The outlet end of the drain hose must be at least 20" (50 cm) above the base of the machine. At this point it is possible for the water to be discharged into a sink, standpipe or drainpipe. No more than 6" of the drain hose should insert into a standpipe. Assure an air break is available to prevent the machine from siphoning in a standpipe. IMPORTANT Make sure the drain hose is not kinked and the water flow is not restricted. Standpipe Drain System: When a standpipe installation is used it must be at least 1 " ( cm) in diameter with a minimum carry away capacity of 7 gallons (26 liters) per minute. Wall or Floor Standpipe Drain: Top of standpipe must be at least 25" (62 cm) high and no higher than 34" (86 cm) from bottom of washer (A & B). Page 3 EXHAUSTING The appliance should not be exhausted into a chimney, wall, ceiling, or any concealed space of a building. Only rigid or flex metal/metallic duct should be used for exhausting, unless the appliance has been investigated for use with non-metal/metallic duct (See Fig.)

10 7). To prevent large amounts of lint and moisture from accumulating and to maintain drying efficiency, consider exhausting outdoors. OPTIONAL AIR OUTLET FILTER The optional air outlet filter (Fig. 6 Page 3) is included as an IMPORTANT SAFETY INSTRUCTIONS WARNING - To reduce the risk of fire, electrical shock, or injury to persons when using your appliance, follow basic precautions, including the following: Read all instructions before using the appliance. Do not wash or dry articles that have been previously cleaned washed or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they emit vapors that could ignite or explode. Do not allow children to play on or in the appliance. Close supervision of children is necessary. Before the appliance is removed from service or discarded remove the door to the washer-dryer compartment. Do not reach into the appliance if the drum is moving.