Example: air traffic controller

papercraft by guardabosques

FL OWERS papercraft by guardabosquesFL OWERS papercraft by guardabosquesWhat you need:Assembling tips:cutmountain foldvalley fold Tools: scissors or utility/craft knife; all-purpose glue or school glue ; and perforation cutter (optional). Print in Letter-size paper. Ideal paper weight: 150 to 200 GSM. Please notice which pages have a front and back side to print on the same sheet. Mark the dotted lines with the backside of a cutter s cutting edge or a ballpoint pen without ink if you don t have a perforation knife. It is recomended that you mark the lines before cutting the outlines. Cut the pieces as you need them, so you don t lose the references. Stick one flap at a time using small amounts of glue . Press for a few seconds to make sure each one is well glued. 1: Petals. Paste pieces A1, A2 and A3 on top of one another as shown in this 2: Stem and leaves.

Fold piece B2 and paste its white sides together. Make sure to not glue the upper side, and leave it as shown in the picture. Join the leaves where referenced on the stem. Paste pieces C1, C2 and C3 one on top of the other. It should look like this. FLOWER C STEP 1: Stamens.

Tags:

  White, Papercraft, Glue, Papercraft by guardabosques, Guardabosques

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Advertisement

Transcription of papercraft by guardabosques

1 FL OWERS papercraft by guardabosquesFL OWERS papercraft by guardabosquesWhat you need:Assembling tips:cutmountain foldvalley fold Tools: scissors or utility/craft knife; all-purpose glue or school glue ; and perforation cutter (optional). Print in Letter-size paper. Ideal paper weight: 150 to 200 GSM. Please notice which pages have a front and back side to print on the same sheet. Mark the dotted lines with the backside of a cutter s cutting edge or a ballpoint pen without ink if you don t have a perforation knife. It is recomended that you mark the lines before cutting the outlines. Cut the pieces as you need them, so you don t lose the references. Stick one flap at a time using small amounts of glue . Press for a few seconds to make sure each one is well glued. 1: Petals. Paste pieces A1, A2 and A3 on top of one another as shown in this 2: Stem and leaves.

2 Fold pieces A4, A5, A6 and A7 in half, pasting their white sides together. Join the leaves where referenced on the stem, then paste the flower on top on the opposite side and it s ready!It should look like 1: Petals. Paste one segment at a time of piece B1It should look like the stem to the flower as shown in the picture, and it s ready!STEP 2: Stem. Fold piece B2 and paste its white sides together. Make sure to not glue the upper side, and leave it as shown in the the leaves where referenced on the pieces C1, C2 and C3 one on top of the should look like CSTEP 1: Stamens. Paste the tab of piece C3 indicat-ed in the graphic. Then close the bottom with the circular 2: Petals. Paste the tab indicated in this picture of piece C1, then paste the base, leaving the tabs on the outside bottom. Repeat the same for piece 3: Stem.

3 Fold piece C4 and paste its white sides together. Join the leaves where referenced on the stem, then paste the flower on top of the opposite side and it s ready!A1A2A3A3A4A6A5A7A5A6A7A2A1B2B1B2B3 B4B3B4 FRONT SIDEOF FLOWER B(print front and backon the same sheet)BACK SIDEOF FLOWER BC1C2C3C3C2C1C5C4C5 FRONT SIDEOF FLOWER C(print front and backon the same sheet)C4 BACK SIDEOF FLOWER C


Related search queries