Example: tourism industry
Parshall Flume Users Manual - Openchannelflow
DIMENSIONS The master dimensions for Parshall flumes with throat widths from 1-inch to 144-inches are found in Figure 1. DIMENSIONAL TOLERANCES ASTM D1941 requires that Parshall flume dimensions be within 2% of nominal, while JIS B7553 requires tolerance of +/- 1 to 1.5%, depending upon flume size.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
6-inch parshall flume discharge table - Openchannelflow
www.openchannelflow.comFormulas (H in feet): CFS = 2.06 H ft. 1.58 GPM = 924.5 H ft. 1.58 MGD = 1331 H ft. Formulas (H in meters): L/S = 381.2 H m 1.58 M3/HR = 1372 H m 1.58 6-Inch Parshall Flume Discharge Table
90º V-Notch Weir Discharge Table - Openchannelflow
www.openchannelflow.comFormulas (H in feet): CFS = 2.500 H ft. 2.5 GPM = 1122 H ft. 2.5 MGD = 1.616 H ft. Formulas (H in meters): L/S = 1380 H m 2.5 M3/HR = 4969 H m 2.5 FEET INCHESMETERS CFS GPM MGD L/S M3/HR 0.01 0.12 0.0030 0.02 0.24 0.0061 0.03 0.36 0.0091
Related documents
TABLE 3 DIMENSIONS OF LONG RADIUS ELBOWS
www.steelmarts.comTABLE 4 DIMENSIONS OF LONG RADIUS-REDUCING ELBOWS Nominal Nominal Pipe Outside Diameter Center- Pipe Outside Diameter Center-at Bevel at Bevel Size to-End, Size to-End, (NPS) DN Large End Small End A (NPS) DN Large End Small End A 2 × 11⁄ 2 50 × 40 60.3 48.3 76 10 × 8 250 × 200 273.0 219.1 381 2 × 11⁄
DUCTILE IRON FLANGED FITTINGS - McWane Ductile
www.mcwaneductile.comface dimensions and the same flange drilling as ANSI B16.1 fittings, but differ slightly in wall thickness. Ductile iron C110/A21.10 flanged fittings are rated for 150 or 250 psi water working pressure as listed in the tables. Long radius and reducing elbows, reducing on-the-run tees, side outlet fittings, eccentric reducers and
DIMENSIONS OF LONG RADIUS ELBOWS DIMENSIONS OF …
www.awaji-m.jpDIMENSIONS OF LONG RADIUS ELBOWS Butt-welding Fittings Butt-welding Fittings DIMENSIONS OF SHORT RADIUS ELBOWS 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 5 6 8 10 12 14 16 18 20 22 24 21.3 26.7 33.4 42.2 48.3 60.3 73.0 88.9 101.6 114.3 141.3 168.3 219.1 273.0 323.8 355.6 406.4 457 508
Hydraulic Considerations in Pumping System Design
cdn.ymaws.com• Use long radius elbows for vertical suction bends • Avoid creating high points • On suction, use eccentric reducers with flat side up • Continuously rising discharge pipe alignment • Provide isolation valves • Include restrained flexible couplings • Pipe/flanges rated for worst case pressures, including surge / test pressures 31
Victaulic Grooved End Fittings
static.victaulic.comNo. 100 90° Long Radius Elbow No. 110 45° Long Radius Elbow C to E C to E C to E C to E C to E C to E C to E Standard and GSNK Size No. 10 90º Elbow No. 11 45º Elbow No. 12 22 ½° Eblow No. 13 11 ¼° Eblow No. 100 90° Long Radius Elbow No. 110 45° Long Radius Elbow Nominal Actual Outside Diameter C to E Approx. Wgt. (Each) C to E Approx ...
Walkerduct Pro Series - Construction
sweets.construction.comPreset dimensions are 4 1/8" wide x 4 13/16" long [105mm x 123mm]. 421 Mudcap – Steel replacement cap for preset. Recessed to hold 3/8" [9.5mm] concrete. 422GR (Green) Marker Cap – Replaces mudcap 422RD (Red) on preset to indicate location of the last insert in each run. Select color for each service.