Power MOSFET - Vishay Intertechnology

1 Document Number: A, 28-Jul-081 Power MOSFETIRFP460, SiHFP460 Vishay SiliconixFEATURES Dynamic dV/dt Rating Repetitive Avalanche Rated Isolated Central Mounting Hole Fast Switching Ease of Paralleling Simple Drive Requirements Lead (Pb)-free AvailableDESCRIPTIONT hird generation Power MOSFETs from Vishay provide thedesigner with the best combination of fast switching,ruggedized device design, low on-resistance andcost-effectiveness. The TO-247 package is preferred for commercial-industrialapplications where higher Power levels preclude the use ofTO-220 devices.

2 The TO-247 is similar but superior to theearlier TO-218 package because its isolated mounting also provides greater creepage distances between pins tomeet the requirements of most safety Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).b. VDD = 50 V, starting TJ = 25 C, L = mH, RG = 25 , IAS = 20 A (see fig. 12).c. ISD 20 A, dI/dt 160 A/ s, VDD VDS, TJ 150 mm from SUMMARYVDS (V)500 RDS(on) ( )VGS = 10 V (Max.) (nC)210 Qgs (nC)29 Qgd (nC)110 ConfigurationSingleN-Channel MOSFET GDSTO-247 GDSA vailableRoHS*COMPLIANTORDERING INFORMATIONP ackageTO-247 Lead (Pb)

3 -freeIRFP460 PbFSiHFP460-E3 SnPbIRFP460 SiHFP460 ABSOLUTE MAXIMUM RATINGS TC = 25 C, unless otherwise notedPARAMETER SYMBOLLIMITUNITD rain-Source Voltage VDS500V Gate-Source VoltageVGS 20 Continuous Drain CurrentVGS at 10 VTC = 25 C ID20 ATC = 100 C 13 Pulsed Drain CurrentaIDM 80 Linear Derating C Single Pulse Avalanche EnergybEAS 960mJ Repetitive Avalanche CurrentaIAR 20A Repetitive Avalanche EnergyaEAR28mJ Maximum Power

4 DissipationTC = 25 C PD280W Peak Diode Recovery dV/dtcdV/dt Operating Junction and Storage Temperature RangeTJ, Tstg- 55 to + 150 C Soldering Recommendations (Peak Temperature)for 10 s300dMounting Torque6-32 or M3 screw10 lbf m* Pb containing terminations are not RoHS compliant, exemptions may apply Number: 912372S-81360-Rev. A, 28-Jul-08 IRFP460, SiHFP460 Vishay SiliconixNotesa. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).b. Pulse width 300 s; duty cycle 2 %.

5 THERMAL RESISTANCE RATINGSPARAMETER Junction-to-AmbientRthJA-40 C/WCase-to-Sink, Flat, Greased Junction-to-Case (Drain) TJ = 25 C, unless otherwise notedPARAMETER SYMBOLTEST CONDITIONS Breakdown Voltage VDS VGS = 0 V, ID = 250 A 500--V VDS Temperature Coefficient VDS/TJ Reference to 25 C, ID = 1 mA C Gate-Source Threshold Voltage VGS(th)

6 VDS = VGS, ID = 250 A Gate-Source Leakage IGSS VGS = 20 V-- 100nA Zero Gate Voltage Drain Current IDSS VDS = 500 V, VGS = 0 V --25 A VDS = 400 V, VGS = 0 V, TJ = 125 C --250 Drain-Source On-State Resistance RDS(on) VGS = 10 VID = 12 Forward Transconductance gfs VDS = 50 V, ID = 12 Ab13--S DynamicInput Capacitance Ciss VGS = 0 V, VDS = 25 V, f = MHz, see fig. 5 -4200-pFOutput Capacitance Coss -870-Reverse Transfer Capacitance Crss -350-Total Gate Charge Qg VGS = 10 V ID = 20 A, VDS = 400 V see fig.

7 6 and 13b--210nC Gate-Source Charge Qgs --29 Gate-Drain ChargeQgd --110 Turn-On Delay Time td(on) VDD = 250 V, ID = 20 A ,RG = , RD = 13 , see fig. 10b-18-nsRise Timetr -59-Turn-Off Delay Time td(off) -110-Fall Time tf -58-Internal Drain Inductance LD Between lead,6 mm ( ")

8 From package and center of die contact Internal Source InductanceLS-13-Drain-Source Body Diode CharacteristicsContinuous Source-Drain Diode Current ISMOSFET symbolshowing the integral reversep - n junction diode--20 APulsed Diode Forward CurrentaISM--80 Body Diode VoltageVSDTJ = 25 C, IS = 20 A, VGS = 0 Diode Reverse Recovery TimetrrTJ = 25 C, IF = 20A, dI/dt = 100 A/ sb-570860nsBody Diode Reverse Recovery CForward Turn-On TimetonIntrinsic turn-on time is negligible (turn-on is dominated by LS and LD)DSGSDG Document Number: A, 28-Jul-083 IRFP460, SiHFP460 Vishay SiliconixTYPICAL CHARACTERISTICS25 C, unless otherwise notedFig.

9 1 - Typical Output Characteristics, TC = 25 CFig. 2 - Typical Output Characteristics, TC = 150 CFig. 3 - Typical Transfer CharacteristicsFig. 4 - Normalized On-Resistance vs. TemperatureVDS, Drain-to-Source Voltage (V)ID, Drain Current (A)20 s Pulse WidthTC = 25 V101100100101 BottomTo pVGS 15 V 10 VBottomTo pVGS15 V10 V20 s Pulse WidthTC = 150 C101100100101ID, Drain Current (A)91237_02 VDS, Drain-to-Source Voltage (V)91237_0325 C150 C20 s Pulse WidthVDS = 50 V101100ID, Drain Current (A)VGS, Gate-to-Source Voltage (V)5678910491237_04ID = 20 AVGS = 10 60 - 40 - 200 20 40 6080 100 120 140 160TJ, Junction Temperature ( C)RDS(on), Drain-to-Source On Resistance(Normalized)

10 Number: 912374S-81360-Rev. A, 28-Jul-08 IRFP460, SiHFP460 Vishay SiliconixFig. 5 - Typical Capacitance vs. Drain-to-Source VoltageFig. 6 - Typical Gate Charge vs. Gate-to-Source VoltageFig. 7 - Typical Source-Drain Diode Forward VoltageFig. 8 - Maximum Safe Operating Area91237_0510 00080006000400002000100101 Capacitance (pF)VDS, Drain-to-Source Voltage (V)CissCrssCossVGS = 0 V, f = 1 MHzCiss = Cgs + Cgd, Cds ShortedCrss = CgdCoss = Cds + Cgd91237_06ID = 20 AVDS = 250 VFor test circuitsee figure 13 VDS = 100 VVDS = 400 VQG, Total Gate Charge (nC)VGS, Gate-to-Source Voltage (V)2016128040402001601208091237_07102 VSD, Source-to-Drain Voltage (V)ISD, Reverse Drain Current (A) C150 CVGS = 0 s100 s1 ms10 msOperation in this area limitedby RDS(on)