Example: tourism industry
PRODUCT DATA SHEET Sikacrete®-211
Refer to ACI 305 the "Guide to Hot Weather Concreting" or ACI 306 the "Guide to Cold Weather Concreting" when there is a need to place this product while either hot or cold temperatures prevail. Thinner placements will be more sensitive to the temperature conditions. CURING TREATMENT As per ACI recommendations for Portland-cement
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
PRODUCT DATA SHEET Sika® FerroGard®-903
usa.sika.comreinforced, prestressed, precast, post tensioned or marine concrete. Use of Sika® FerroGard®-903: Steel-reinforced concrete, bridges and highways exposed to corrosive environments (deicing salts, weathering) Building facades and balconies Steel-reinforced concrete in or near a marine environment Parking garages
Liquid Seam Sealant - Sika AG
usa.sika.comConstruction Sikaflex® 110 Liquid Seam Sealant Description Sikaflex 110 Liquid Seam Sealant is a non-shrinking, 100% solids, solvent free polyether based, moisture curing, elastomeric sealant. It forms a weather-tight seal when applied over sheathing board joints.
PRODUCT DATA SHEET Sika® Primer-207
usa.sika.comIMPORTANT NOTE If Sika® Primer-207 is used below 5 °C further testing under worst case conditions are man-datory. Sika® Primer-207 is a moisture reactive sys-
Sikadur Epoxies Application Guide - Sika …
usa.sika.comSikadur® Epoxies Application Guide LPL = Long Pot Life cps = centipoise Reference approximate viscosity water = 1 cps olive oil = 100 cps motor oil = 1000-2000 cps Crack Repair Patching Overlay Bonding Adhesive Anchor Bolts Base Plate Grouts USDA Approved Potable Water Approved ASTM C-881 Interior Exterior Int. Exterior Type …
Part 1 - General - Sika AG
usa.sika.comA. Sikadur Injection Gel as manufactured by Sika Corporation, 1682 Marion Williamsport Road, Marion, Ohio 43302 is considered to conform to the requirements of this specification.
PRODUCT DATA SHEET SikaTop®-123 Plus
usa.sika.com0 g/l (EPA method 24) LIMITATIONS Do not use solvent-based curing compound. Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI. For additional information on substrate preparation, refer to ICRI Guideline No. 310.2R. If aggressive means of substrate preparation is
SikaSwell S-2 SikaSwell S-2
usa.sika.comApplication Recommended application temperatures: 50°-90°F. Extrude material using Sika MK-5 bulk caulking gun or other approved bulk gun. Cut the nozzle to obtain a triangular extrusion section with a size fulfilling effective needs (or use nozzle included in carton of SikaSwell S-2). Apply a uniform, continuous bead to the hardened concrete.
PRODUCT DATA SHEET Sikalastic®-710 Base
usa.sika.comMetal - Should be thoroughly cleaned by grinding or blast cleaning to near white metal (SSPC SPS-10). Priming Primer Selection - Determine maximum moisture content of concrete substrate by weight with a Tramex CME or CMExpert type concrete moisture meter. Sikalastic® Primer – For concrete decks with a maximum
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comSpecification TT-S-00230C, Type II, Class A. Meets ASTM C-920, Type S, Grade NS, Class 35, use T, NT, O, M, G, I, A. Canadian standard CAN/CGSB 19.13-M87. USES Designed for all types of joints where maximum depth of sealant will not exceed 1/2 in. Excellent for small joints and fillets, windows, door
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comJoint dimension should allow for 1/4 inch minimum and 1/2 inch maximum thickness for sealant. Proper design is 2:1 width to depth ratio, For use in horizontal joints in traffic areas, the absolute minimum depth of the sealant is 1/2 in. and closed cell backer rod is recommended. Removal Use personal protective equipment (chemical resistant
Related documents
ACI 306R-16: Guide to Cold Weather Concreting
www.concrete.orgACI 306R-16: Guide to Cold Weather Concreting Author: ACI Committee 306 Subject: This document guides specifiers, contractors, and concrete producers through the selection processes that identify methods for cold weather concreting. The objectives of cold weather concreting practices are to: a\) prevent damage to concrete due to freez\ ing at ...
IS 7861-1 (1975): Code of practice for extreme weather ...
law.resource.orgSep 22, 1975 · pertaining to extreme weather concreting. This standardis thefint Indian Standard on the subject and deals with hot weather concreting. Part II, which is under preparation. will deal with cold weather concreting. 0.3 Special problems are encountered in the preparation, placement and curing of concrete in hot weather. High temperatures result in ...
306R-16: Guide to Cold Weather Concreting
www.concrete.orgThe conditions of cold weather concreting exist when the air temperature has fallen to, or is expected to fall below, 40°F (4°C) during the protection period. The protection period is defined as the amount of time recommended to prevent concrete from being adversely affected by exposure to cold weather during construction. Concrete placed during
COLD WEATHER CONCRETE GUIDE FOR STRUCTURAL …
cemstone.comDuring the fall and winter seasons, ACI 306R-16 recommends that a cold weather concreting plan be implemented for every concrete placement. The goal of this plan is to prevent the concrete from being adversely affected by exposure to cold weather during construction. The time to accomplish this is called the protection period.
Some Examples for CO-PO(1-3)Mapping and Corresponding ...
www.nbaind.orgas Hot weather concreting, Underwater concreting, Mass concreting, High early strength requirement in say 3 days. PO 1: Engineering Knowledge : Apply the knowledge of mathematics, science, engineering fundamentals, and an engineering specialization to the solution of complex engineering problems ...
GENERAL SPECIFICATIONS 11 CONCRETE
www1.nyc.gov8.6 Protection, Weather, Placing, and Preparation of Forms 8-7 8.7 Bonding 8-8 8.8 Concreting Under Water 8-9 8.9 Protection and Cleaning of Exposed Structural Steel 8-9 8.10 Grout and Mortar 8-10 8.11 Grouting and Protection of Various Bases 8-11 Chapter 9 - Repair of Surface Defects 9.1 General 9-1 9.2 Submittals 9-1
Moisture in New Homes - NHBC
www.nhbc.co.ukactivities like concreting, laying screed floors, bricklaying, plastering and painting. Up to 8000 litres of water (about 800 full buckets) may be included in mixtures and materials as construction proceeds, though this varies depending on the design of the home. This construction moisture will steadily dry out over time
WATERPROOFING SikaSwell® HYDROPHILIC PROFILES AND …
www.sikawaterproofing.co.ukThe application should take place shortly before concreting to avoid premature swelling. The waterstop must have continuous contact onto the base in the joint area to provide maximum and proper sealing capacity and to prevent any leakage at a later stage. SikaSwell® sealant can be applied as adhesive for the profiles