PROMOUNT BACKING SYSTEM

1 PROMOUNT Stick & Stay Flush Mount BACKING SYSTEM Benefits/Advantages Easily Installs with Stick & Stay Mounting Adhesive Adjusts to various stud layout and stud spacing installs one stud bay at a time. Works with 1-1/4 , 1-5/8 , 2 , 2-1/2 and 3 stud flanges one part does it all. Low Profile Flange to accommodate vertical in-wall MEP trades work without notching. Save Money, Re-Use STUD and TRACK scrap material as BACKING Meets OSHPD, ADA, DSA wall BACKING standards IBC 2012 / CBC 2013 Mounts FLUSH with the framing surface. No Material Build-up for smoother, flatter drywall. No Screw Pops. Approved for Type 1, Type 2, Type 3 and Type 4 BACKING LoadsBasic UseProMount is a light gauge steel BACKING [mounts] SYSTEM and BACKING plates that install stud bay-by-stud bay, eliminating the troubles of notched track BACKING .

2 PROMOUNT BACKING mounts are secured together with an adhesive label that enables it to be easily installed on vertical studs. PROMOUNT BACKING plates (PBP) are designed with low profile returns allowing maximum in-wall [stud cavity] space for MEP trades installed work. The PROMOUNT components install flush with the stud members, eliminating excess material build up. Moreover, standard 6-inch (33 mil. or 54 mil. or greater) stud and track scrap materials can be re-used and installed as BACKING plates. This pre-engineered framing SYSTEM can be used in lieu of flat strap BACKING , notched track BACKING and other screwed and welded BACKING methods that are built-up and result in material overlaps. The PROMOUNT BACKING SYSTEM is a cost effective means of installing BACKING when stud lay out is made of 16-gauge and 14-gauge (54 & 68 mil.)

3 Galvanized steel complying with industry standard ASTM performance criteria for metal stud framing members. The members fasten with No. 10 sheet metal screws (SMS). Code Compliance Seismic Design Criteria (Max.) Fp calculated with: SDS = (MAX.) & Ip = SDS = (MAX.) & Ip = z/h = 1 For greater design criteria contact CEMCO technical services for project specific design. International Building Code 2012 (IBC) California Building Code 2013 (CBC) America Disability Act (ADA): PROMOUNT meets the load requiems of ADA America Disability Act section Handrails, Grab Bars and Tub and Shower Seats. 250 point loading is achieved in the maximum bending moment, shear stress, direct and torsional stresses, lateral load, direct tension force, and combined shear stress.

4 OSHPD California Hospital Compliance: PROMOUNT meets the load requirements of OSHPD for Full Height Cabinets or Equipment, Base Cabinets or Equipment, Wall Cabinets or Equipment equal top 2010 CBC Standard Partition Wall Details, published Jan. 6th BACKING SYSTEMC orporate Headquarters 263 North Covina LaneCity of Industry, CA 91744 Phone: : FacilitiesCity of Industry, CA Denver, COFt. Worth, TXPittsburg, CAStructural Engineering/Design1001-A Pittsburgh Antioch HwyPittsburg, CA 94565 Phone: : Services263 North Covina LaneCity of Industry, CA 91744 Phone: : Headquarters & Main Manufacturing Facility263 N Covina Lane, City of Industry, CA 91744 Phone: | Fax: California Manufacturing Facility1001-A Pittsburg Antioch Hwy Pittsburg, CA 94565 Phone: | Fax: Colorado Manufacturing Facility490 Osage Street, Denver, CO 80204 Phone: | Fax: Worth Texas Manufacturing Facility8600 Will Rogers Blvd.

5 , Ft. Worth, TX 76140 Phone: | Fax: STICK & STAY ADHESIVE LABEL, CONNECTS PROMOUNT BRACKETSUS Patents 7,739,852 & 8,141,319. Owned by Brady Innovations, LABEL WITHINSTRUCTIONS PRINTED ON OUTSIDEPROMOUNT BACKING SYSTEMC orporate Headquarters 263 North Covina LaneCity of Industry, CA 91744 Phone: : FacilitiesCity of Industry, CA Denver, COFt. Worth, TXPittsburg, CAStructural Engineering/Design1001-A Pittsburgh Antioch HwyPittsburg, CA 94565 Phone: : Services263 North Covina LaneCity of Industry, CA 91744 Phone: : Headquarters & Main Manufacturing Facility263 N Covina Lane, City of Industry, CA 91744 Phone: | Fax: California Manufacturing Facility1001-A Pittsburg Antioch Hwy Pittsburg, CA 94565 Phone: | Fax: Colorado Manufacturing Facility490 Osage Street, Denver, CO 80204 Phone: | Fax: Worth Texas Manufacturing Facility8600 Will Rogers Blvd.

6 , Ft. Worth, TX 76140 Phone: | Fax: Designation/NomenclatureMember Identification shall be as shown:1. PROMOUNT Nomenclature shall be as shown: 123600 PBP54-1 600 Series PROMOUNT BACKING System2 Style: Example: BACKING Plate = PBP The three designations utilized by the designator SYSTEM are: PBP = PROMOUNT BACKING Plate3 Material Thickness: Example: in. = 54 mils; 1 in. = 1/1000 in. Material thickness is the minimum base metal thickness in mils. Minimum base metal thickness represents 95% of design PROMOUNT BACKING Brackets are not required to be used in pairs on each BACKING Extend BACKING plate on bay beyond edge of cabinet or equipment to fasten to adjacent BACKING stud. However, BACKING plates are not required to continue an additional stud bay beyond equipment unless required by See chart for approved use conditions for BACKING Minimum BACKING stud thickness is 33 mil.

7 For BACKING studs with flanges larger than 2", 54 mil. is PROMOUNT BACKING plates come in 14-3/8" lengths for 16" framing and 22-3/8" lengths for 24" framing. PROMOUNT BACKING plates, stud sections and track sections can be cut to length to meet vertical stud bay spacing as PLATESPROMOUNTBACKING BRACKETS " " "(3) " " " " " " " " "16 GAUGE (54 MIL.) - "14 GAUGE (68 MIL.) - " " " " " " " " PROMOUNT BACKING SYSTEMC orporate Headquarters 263 North Covina LaneCity of Industry, CA 91744 Phone: : FacilitiesCity of Industry, CA Denver, COFt. Worth, TXPittsburg, CAStructural Engineering/Design1001-A Pittsburgh Antioch HwyPittsburg, CA 94565 Phone: : Services263 North Covina LaneCity of Industry, CA 91744 Phone: : Headquarters & Main Manufacturing Facility263 N Covina Lane, City of Industry, CA 91744 Phone: | Fax: California Manufacturing Facility1001-A Pittsburg Antioch Hwy Pittsburg, CA 94565 Phone: | Fax: Colorado Manufacturing Facility490 Osage Street, Denver, CO 80204 Phone: | Fax: Worth Texas Manufacturing Facility8600 Will Rogers Blvd.

8 , Ft. Worth, TX 76140 Phone: | Fax: Gauge Steel / Material Standards1. Details on this sheet are acceptable alternates for BACKING details shown in the contract All work shall meet the requirements of the following: A. American Iron and Steel Institute (AISI) design of cold formed steel structural members B. American Society for Testing and Materials (ASTM)3. All materials conform to the following: A. 54 mil (gauge) and heavier: 50 ksi min. yield, 65 ksi min. tensile strength galvanized steel per ASTM A653 - Grade 504. All calculated properties per AISI specification are based on the following thickness: A. 14 Gauge (68 mil) " B. 16 Gauge (54 mil) "5. Maintain a minimum of 3/8" edge distance between center of screw and edge of punchouts.

9 Relocate screws if Diagrams shown assume that the primary structure intended to support and resist loads produced by the interior framing SYSTEM have been adequately designed for this purpose unless specifically Screws shall be #10 sheet metal screws with sufficient length to ensure penetration into steel stud by at least 3 full diameter Seismic info: Fp calculated with: Sds = (max) & Ip = OR Sds = (max) & Ip = z/h = 19. This sheet is for the PROMOUNT BACKING SYSTEM only. The design of the BACKING studs and their attachment to the structure is not a part of this CUT TRACK OR STUD AT STAIR HANDRAILSTYPE 4 BACKINGAT ALL GRAB BARSTYPE 1-4 BACKING DEPENDING ON VERTICAL LOAD REQUIREMENT.

10 SEE CHARTS FOR EXAMPLES OF ITEMS SUPPORTED BY EACH BACKING BACKING SYSTEMC orporate Headquarters 263 North Covina LaneCity of Industry, CA 91744 Phone: : FacilitiesCity of Industry, CA Denver, COFt. Worth, TXPittsburg, CAStructural Engineering/Design1001-A Pittsburgh Antioch HwyPittsburg, CA 94565 Phone: : Services263 North Covina LaneCity of Industry, CA 91744 Phone: : Headquarters & Main Manufacturing Facility263 N Covina Lane, City of Industry, CA 91744 Phone: | Fax: California Manufacturing Facility1001-A Pittsburg Antioch Hwy Pittsburg, CA 94565 Phone: | Fax: Colorado Manufacturing Facility490 Osage Street, Denver, CO 80204 Phone: | Fax: Worth Texas Manufacturing Facility8600 Will Rogers Blvd.