Prowirl 72, Vortex Measuring System - Controls Warehouse

1 BA084D/06/ 50103643 proline Prowirl 72. Valid as of software version: V (amplifier). Vortex Flow Measuring System operating instructions Brief operating instructions proline Prowirl 72. Brief operating instructions These brief operating instructions explain how to commission your Measuring device quickly and easily: Safety instructions Page 7.. Installation Page 11.. Wiring Page 21.. Display and operating elements Page 27.. Commissioning with "QUICK SETUP" Page 40. You can commission your Measuring device quickly and easily using the special Quick Setup menu. It allows you to configure important basic functions via the local display, for example display language, measured variables, engineering units, signal type etc.

2 Customer-specific configuration / Page 75 ff. Description of device functions Complex measurement tasks require the configuration of additional functions which you can individually select, set and adapt to your process conditions using the function matrix. The function matrix of the Measuring device and all the functions are described in detail in the "Description of device functions" section. 2 Endress+Hauser proline Prowirl 72 QUICK SETUP for quick commissioning QUICK SETUP for quick commissioning ++ Quick Setup E Quick Setup E+. - Esc + E. Commission HOME-POSITION Language Application Measuring Unit Type Volume Flow Calculated Mass Flow Corrected Volume Flow Unit Unit Unit Flow Flow Flow Unit Unit Unit Totalizer Totalizer Totalizer Unit Unit Density Density operating operating Density Density Reference Density Selection output type Current Pulse /.

3 Quit output Status output Operation Mode Pulse Status Vortex Freq. PFM. Current Pulse Assign span value status Value Pulse On 20 mA width value Time Output Off constant signal value Failsafe Failsafe Time mode mode constant Configuration another output ? Yes No Automatically configuration display ? Yes No Automatically parameterization of the display ! Note! The display returns to the QUICK SETUP COMMISSIONING cell if you press the ESC key combination F06-72xxxxxx-19-xx-xx-en-000. during interrogation. Only the output (current output or pulse/status output) not yet configured in the current Quick Setup is offered for selection after the first cycle.

4 The YES option appears as long as a free output is still available. "NO" is the only option displayed when no further outputs are available. When "YES" is selected, the flow is assigned to line 1 of the local display and the totalizer to line 2. Endress+Hauser 3. QUICK SETUP for quick commissioning proline Prowirl 72. 4 Endress+Hauser proline Prowirl 72 Contents Contents 1 Safety instructions .. 7 Error message display .. 30. Communication (HART) .. 31. Designated use .. 7. operating options .. 31. Installation, commissioning and operation .. 7. Device variables and process Operational safety.

5 7 variables .. 32. Return .. 8 Universal / common practice Notes on safety conventions and icons .. 8 HART commands .. 32. Device status / error messages .. 37. 2 Identification .. 9 Switching HART write protection Device designation .. 9 on/off .. 38. Nameplate on the transmitter .. 9. Nameplate of the sensor, remote 6 Commissioning .. 39. version .. 10 Function check .. 39. CE mark, declaration of conformity .. 10 Commissioning .. 39. Registered trademarks .. 10 Switching on the Measuring device . 39. Commissioning Quick Setup.. 40. 3 Installation .. 11. Incoming acceptance, transport, storage.

6 11 7 Maintenance .. 42. Incoming acceptance .. 11. Transport .. 11 8 Accessories .. 43. Storage .. 11. Installation conditions .. 12 9 Trouble-shooting .. 45. Dimensions .. 12 Trouble-shooting instructions .. 45. Installation location .. 12 System error messages .. 46. Orientation .. 12 Process errors without messages .. 48. Heat insulation .. 13 Response of outputs to errors .. 50. Inlet and outlet run .. 14 Spare parts .. 51. Vibrations .. 15 9. 6 Installing and removing electronics boards .. 52. Limiting flow .. 15 Non-Ex, Ex-i version .. 52. Installation instructions .. 16 Ex-d version.

7 54. Mounting the sensor .. 16 Software history .. 56. Rotating the transmitter housing .. 17. Mounting the transmitter (remote 10 Technical data .. 57. version) .. 18. Technical data at a glance .. 57. Rotating the local display .. 19. Application .. 57. Post-installation check .. 19. Function and System design .. 57. 4 Wiring .. 21 Input .. 57. Output .. 58. Connecting the remote version .. 21 Power supply .. 59. Connecting the sensor .. 21 Performance characteristics .. 60. Cable specifications .. 22 Mechanical construction .. 62. 4. 2 Connecting the Measuring unit .. 22 Human interface.

8 63. Connecting the transmitter .. 22 Certificates and approvals .. 63. Terminal assignment .. 24 Accessories .. 64. HART connection .. 25 Documentation .. 64. Degree of protection .. 26 Dimensions of transmitter, Post-connection check .. 26 remote version .. 64. Dimensions of Prowirl 72 W .. 65. 5 Operation .. 27 Dimensions of Prowirl 72 F .. 66. Display and operating elements .. 27 Dimensions of Prowirl 72 F, Dualsens version 70. The function matrix: layout and use .. 28 Dimensions of flow conditioner .. 73. General notes .. 29. Enabling the programming mode .. 29. Disabling the programming mode.

9 29. Endress+Hauser 5. Contents proline Prowirl 72. 11 Description of device functions .. 75. Illustration of the function matrix .. 75. Description of functions .. 76. Group MEASURED VALUES .. 76. Group System UNITS .. 77. Group QUICK SETUP .. 81. Group OPERATION .. 82. Group USER INTERFACE .. 84. Group TOTALIZER .. 86. Group CURRENT OUTPUT .. 88. Group PULSE/STATUS OUTPUT .. 90. Information on the response of the status output .. 97. Group COMMUNICATION .. 98. Group PROCESS PARAMETER .. 99. Group System PARAMETER .. 103. Group SENSOR DATA .. 104. Group SUPERVISION .. 106. Group SIMULATION System .

10 108. Group SENSOR VERSION .. 109. Group AMPLIFIER VERSION .. 109. Factory settings .. 110. Metric System units (not for USA and Canada) .. 110. US units (only for USA and Canada) .. 112. Index .. 115. 6 Endress+Hauser proline Prowirl 72 1 Safety instructions 1 Safety instructions Designated use The Measuring System is used to measure the volume flow of saturated steam, over- heated steam, gases and liquids. If the process pressure and process temperature are constant, the Measuring device can also output the flow as the calculated mass flow and corrected volume flow. Resulting from incorrect use or from use other than that designated the operational safety of the Measuring devices can be suspended.