Pulse Proof, High Power Thick Film Chip Resistors - Vishay

1 CRCW-HP Draloric Revision: 16-Sep-161 Document Number: 20043 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT proof , High Power Thick film chip ResistorsThe Pulse proof , high Power Thick film chip Resistors series is the perfect choice for most fields of Power measurement electronics where reliability, stability, high Power rating and excellent Pulse load performance are of major concern.

2 Typical applications include battery management systems in automotive Excellent Pulse load capability Enhanced Power rating Double side printed resistor element AEC-Q200 qualified Material categorization: for definitions of compliance please see APPLICATIONS Automotive IndustrialNotes Marking: See document Surface Mount resistor Marking ( ).(1)Please refer to APPLICATION INFORMATION below.(2)CRCW0402-HP Resistors feature a single side printed resistive layer only.(3)Specified Power rating requires a thermal resistance of Rth = 110 INFORMATIONWhen the resistor dissipates Power , a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board.

3 The rated dissipation applies only if the permitted film temperature is not Resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional SPECIFICATIONSDESCRIPTIONCRCW0402-HP e3 CRCW0603-HP e3 CRCW0805-HP e3 CRCW1206-HP e3 CRCW1210-HP e3 CRCW1218-HP e3 CRCW2010-HP e3 CRCW2512-HP e3 Imperial size04020603080512061210121820102512 Metric size codeRR1005 MRR1608 MRR2012 MRR3216 MRR3225 MRR3246 MRR5025 MRR6332 MResistance range1 to 1 M jumper (0 )

4 Resistance tolerance 5 %; 1 %; %Temperature coefficient 200 ppm/K; 100 ppm/KRated dissipation, P70 (1) W (2) W (3) WOperating voltage, Umax. ACRMS/DC50 V75 V150 V200 V200 V200 V400 V500 VPermissible film temperature, F max. (1)155 COperating temperature range-55 C to +155 CMax. resistance change at P70 for resistance range, | R/R| after:1000 h %8000 h %Permissible voltage against ambient (insulation):1 min, Uins75 V100 V200 V300 V300 V300 V300 V300 VCRCW-HP Draloric Revision: 16-Sep-162 Document Number: 20043 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

5 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT The temperature coefficient of resistance (TCR) is not specified for 0 COEFFICIENT AND RESISTANCE RANGETYPE / SIZETCRTOLERANCERESISTANCEE-SERIESCRCW04 02-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax. = 3 A 10 m 0 -CRCW0603-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax. = 5 A 8 m 0 -CRCW0805-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax.

6 = 6 A 5 m 0 -CRCW1206-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax. = 10 A 5 m 0 -CRCW1210-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax. = 12 A 4 m 0 -CRCW1218-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax. = 20 A 4 m 0 -CRCW2010-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax. = 12 A 5 m 0 -CRCW2512-HP e3 200 ppm/K 5 %1 to 1 M E24 100 ppm/K 1 %1 to 1 M E24; E96 %Jumper, Imax.

7 = 16 A 5 m 0 -PACKAGINGTYPE / SIZECODEQUANTITYPACKAGING STYLEWIDTHPITCHPACKAGING DIMENSIONSCRCW0402-HP e3ED = ET710 000 Paper tape acc. toIEC 60286-3, Type 1a8 mm2 mm 180 mm / 7"EE = EF450 000 330 mm / 13"CRCW0603-HP e3EI = ET250002 mm 180 mm / 7"ED = ET310 000 180 mm / 7"EL = ET420 000 285 mm / "EE = ET820 000 330 mm / 13"EA = ET150004 mm 180 mm / 7"EB = ET510 000 285 mm / "EC = ET620 000 330 mm / 13"CRCW0805-HP e3EA = ET150004 mm 180 mm / 7"EB = ET510 000 285 mm / "EC = ET620 000 330 mm / 13"CRCW1206-HP e3EA = ET150004 mm 180 mm / 7"EB = ET510 000 285 mm / "EC = ET620 000 330 mm / 13"CRCW1210-HP e3EA = ET150004 mm 180 mm / 7"EB =

8 ET510 000 285 mm / "EC = ET620 000 330 mm / 13"CRCW1218-HP e3EK = ET94000 Blister tape acc. toIEC 60286-3, Type 2a12 mm4 mm 180 mm / 7"CRCW2010-HP e3EF = E0240004 mm 180 mm / 7"EJ = E0816 0004 mm 330 mm / 13"CRCW2512-HP e3EG = E6720008 mm 180 mm / 7"EH = E8240004 mmCRCW-HP Draloric Revision: 16-Sep-163 Document Number: 20043 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT NUMBER AND PRODUCT DESCRIPTIONPart Number: CRCW0603562 RFKEAHP Part Number.

9 CRCW06030000Z0 EAHPTYPE / SIZEVALUETOLERANCETCRPACKAGINGSPECIALCRC W0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW1218 CRCW2010 CRCW2512R = decimalK = thousandM = million0000 = jumperD = %F = 1 %J = 5 %Z = jumperK = 100 ppm/KN = 200 ppm/K0 = jumperEAEBECEDEEEFEGEIEJEHEKELup to 2 digitsHP = Pulse proof , high powerProduct Description: CRCW0603-HP 100 562R 1 % ET1 e3 Product Description: CRCW0603-HP 0R0 ET1 e3 CRCW0603-HP100562R1 %ET1e3 TYPE / SIZETCRRESISTANCE VALUETOLERANCE PACKAGINGLEAD (Pb)-FREECRCW0402-HPCRCW0603-HPCRCW0805- HPCRCW1206-HPCRCW1210-HPCRCW1218-HPCRCW2 010-HPCRCW2512-HP 100 ppm/K 200 ppm/K10R = 10 562R = 562 10K = 10 k 1M = 1 M 0R0 = jumper % 1 % 5 %ET1, ET2,ET3, ET4,ET5, ET6,ET7, ET8,ET9, EF4,E02, E08, E67, E82e3 = pure tintermination finishCRCW0603562 RFKEAHPCRCW-HP Draloric Revision: 16-Sep-164 Document Number: 20043 For technical questions, contact.

10 DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT is strictly controlled and follows an extensive set of instructions established for reproducibility. A cermet film layer and a glass-over are deposited on both sides of a high grade (Al2O3) ceramic substrate with its prepared inner contacts on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics.