QS Link Plug-In Power Supply - Lutron Electronics

1 SPECIFICATION SUBMITTALPageJob Name:Job Number:Model Numbers:QS link Plug-In Power SupplyProduct Specification085329b 1 SolutionsQSPS-Px-1-35 VLink Power SupplyQS link Plug-In Power Supply The QS link Plug-In Power Supply provides Power to Lutron QS shading solutions as well as QS system devices and interfaces. The Power Supply plugs into a standard receptacle and delivers 35 V- output voltage which conforms with NEC Class 2 / NEC Class 2 / PELV Power Supply capable of powering Lutron shades, drapery drive units, keypads & accessories Compliant with Department of Energy Efficiency Level VI regulations for External Power Supplies Mounting tabs and small size allow for discrete installation Simple wiring topology to connect QS communication between shades and other QS devices/system components Includes AC Power cord (see below for available plug styles)

2 ModelsQSPS-P1-1-35 VQSPS-P2-1-35 VQSPS-P3-1-35V NEMA 5-15 PlugCEE 7/7 PlugBS 1363 PlugSPECIFICATION SUBMITTALPageJob Name:Job Number:Model Numbers:QS link Plug-In Power SupplyProduct Specification085329b 2 SolutionsSpecificationsPower Input: 120 - 240 V~ 50/60 Hz A Output: 35 V- A 5 W Capable of powering any one Lutron QS window treatment drive OR up to 8 QS PDU s (see QS link Wiring Rules on page 5)Input Wiring Designed to be powered by an AC Power cord with IEC C13 connector Supplied Power cord length: 6 ft ( m) Use Power cord supplied or any approved Power cord that is compatible with the installation site Power Cord Requirements: IEC C13 Connector 300 V, 140 F (60 C) minimum insulation 18 AWG ( mm2) minimum (3-conductor) Minimum length: 6 ft ( m) Maximum length: 10 ft ( m)Output Terminal Wiring 22 AWG 12 AWG (0,5 mm2 4,0 mm2) single wire, solid or stranded Torque: 5 in-lbs (0,5 N m) Strip length.

3 1/4 in (6 mm) Local connections for 4-conductor shade Power /communication, and (2) 3-conductor communication pass-through linksRegulatory Approvals Department of Energy Level VI Compliant NRCan Compliant cULus Listed IEC Compliant (CE Marked) NOM Certified FCC Compliant CCC CertifiedEnvironment Ambient temperature operating range: 32 F to 104 F (0 C to 40 C) Relative humidity: 0% to 90% non-condensing For indoor use only; not approved for plenum installation Thermal dissipation: BTU / hrPerformance +/- 6 kV surge protection (ANSI / IEEE - 1991) +/- 16 kV ESD protection (EIC 61000 - 4 - 2 AIR DISCHARGE) Self-recoverable short circuit / miswire protection on Power output terminals Self-recoverable overload/over temperature protectionWarranty Covered by Lutron Shading Solutions standard warranty.

4 See: Systems SUBMITTALPageJob Name:Job Number:Model Numbers:QS link Plug-In Power SupplyProduct Specification085329b 3 SolutionsFeatures and DimensionsInstallation The Power Supply is designed to plug into a standard receptacle. The Power Supply can be mounted using the mounting tabs and fasteners of appropriate type for the mounting surface. Hand tighten only. Do not use a Power tool to tighten the fasteners. It is recommended to mount Power supplies in a location that will remain accessible. Leave enough cable to allow for servicing, arranged and secured to prevent interference with window treatments or other moving in (103 mm) in (70 mm) in(32 mm)3-Conductor Communication Pass-ThroughMounting TabsLine Voltage Input4-Conductor Shade Power and CommunicationSystem Wiring Overview: QS link Power supplySPECIFICATION SUBMITTALPageJob Name:Job Number:Model Numbers.

5 QS link Plug-In Power SupplyProduct Specification085329b 4 to 8 PDU's total on link (refer to QS link Wiring Rules on the following page) Power and communication link (4 conductor) Provides Power and communication to QS shades and/or keypads Example: Powering one window treatment drive unit (maximum 1 window treatment drive unit per Power Supply )Example: Powering keypadsExample: 2 Power supplies / 2 window treatment drive units, with communication linkCommunication link (3 conductor) Used as a communications pass-through connection for QS link devicesSPECIFICATION SUBMITTALPageJob Name:Job Number:Model Numbers:QS link Plug-In Power SupplyProduct Specification085329b 5 SolutionsQS link Wiring RulesThe following rules must be observed for proper operation.

6 QS wiring is NEC Class 2 / PELV. Follow all applicable local and national codes for proper circuit separation and protection. Power (35 V and COM): 12 - 18 AWG (4,0-1,0 mm ) Communication (MUX and MUX): 22 AWG (0,5 mm ) twisted/shielded pair +35 V- must NEVER be connected between Power supplies Total length of QS link wiring must not exceed 2000 ft (610 m)Options available from Lutron with Power and communication conductors in one cable:GaugeLutron Model Number12 AWG (4,0 mm )QSH-CBL-L-50016 AWG (1,5 mm )QSH-CBL-M-50018 AWG ( mm )GRX-CBL-346S-500*For more information, refer to the QS link Power Draw Unit Specification Submittal (P/N 369405)It is the responsibility of the installer to ensure plenum installations are compliant with all applicable local and national devices powered from one QSPS-Px-1-35 VMaximum total wire length of link wiring based on wire gaugeShades+Controls12 AWG ( mm )16 AWG ( mm )18 AWG ( mm )1 Sivoia QS shade/drapery drive unit+Up to 1 Power Draw Unit*250 ft(75 m)100 ft(30 m)50 ft(15 m)

7 None+Up to 8 Power Draw Units*2000 ft (610 m)1500 ft(450 m)O Lutron is a trademark of Lutron Electronics Co., Inc., registered in the and other countriesNEC is a registered trademark of The National Fire Protection Associatio