Room Controller - Cooper Industries

1 Model #: RC3 Model #: RC3-PL Model #: RC3-PL-N. Greengate Model #: RC3D Model #: RC3D-PL Model #: RC3D-PL-N. Installation Instructions Model #: RC3DE Model #: RC3DE-PL INS #. Model #: RC3DE-PL-N. Room Controller SAFETY INSTRUCTIONS. IMPORTANT SAFEGUARDS. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Installation should be performed by a qualified electrician Installation shall be in accordance with all applicable local and NEC codes Turn the power off at circuit breakers before wiring RC3DE models may contain circuits from more than one power source Designed for indoor installation and use only All new wiring must be fully verified before applying power Servicing of equipment should be performed by qualified service personnel SAVE THESE INSTRUCTIONS.

2 System Overview SPRC-R-20-120. Room Controller (20A Receptacle Control). Normal Power (Above Entry Door). Line Voltage (Line In & Load Out). to J-Box Line Voltage (Low Voltage, Class 2). to Receptacles Emergency Power OCC-RJ45. (Line In & Load Out). RC3DE Model only DSRC-FMOIR. (Multi-zone 0-10V Dimmer Wiring Daylight Sensor). (Dimming Models Only) (Any Greengate Occupancy Sensor). Wallstation Wallstation (Entry) (Additional). RS-485 to other Room Controllers and ControlKeepers System Overview Sample Placement Diagram (For Example Purposes Only).

3 Room Controller Additional Wall/Corner Mount (Above Entry Door). Wallstation Occupancy Sensor General On AV Mode Whiteboard Quiet Time Raise Lower General On Off Entry Wallstation Daylight Window Sensor Room Controller Plastic Enclosure (Model RC3DE shown). The Room Controller is a room based system that simplifies design, code compliance and installation. The Controller connects to occupancy sensors, daylighting Room Controller Metal Enclosure (Model RC3DE-PL shown). sensors, wallstations and receptacle control accessories with provided Click & Go QuickConnect cables, providing a completely operational, out-of-the-box solution.

4 Control up to three switched and three dimmed loads (dependent Specifications on model ordered) without the need for post-installation Input/Output Voltage 120/277 VAC 50/60Hz programming. Maximim Combined Load 20A. Additional advanced integration easily accomodates Ballast: 20A. Demand Response, Alert Mode, A/V Mode and Time Clock requirements. Incandescent: 15A. Motor Load: 1 HP @ 120 VAC. This document shows installation details regarding the Room Controller and accessory products. Emergency Output: (RC3DE only). Ballast: 3A.

5 Incandescent: 3A. CAUTION Class 2 Dimming Output 0-10 VDC, sinks up to 100mA. per output for control of up to 50. Bonding between conduit connections is not automatic and compatible ballasts/drivers. must be provided as part of the installation. Operating Environment 32 F to 104 F (0 to 40 C). Failure to install the Room Controller in the suggested For indoor use only. location (above the entry door) may lead to the provided QuickConnect cabling being too short to reach the intended accessory locations. Adjustable Skylights 6.

6 Purple - Load 3 Out Adjustable Skylights Switchpack White Red - Load 2 Out QuickConnect Cables Receptacle CAUTION: Bonding between conduit connections is not automatic and must be provided as part of the installation. Red BMS/Out 5. Black Sensors Green Sensors Slider Station Integration Controls 4. Yellow - Load 1 Out Wallstations Blue - Load In A/V - Integration Controls Mode +. Demand - Response Alert Mode +. - +. 3. Time Clock - +. 2. White/Orange - 277V N. White/Black - 120V N. Black - Line In 1. Energy Options DIP Switch High End Options Energy Demand Response Occupancy Not Used 1 2 3 4.

7 Default 10% Occ Reset 20% Vac (default). 30%. Low End 40%. Status Adjustment 0-10V Gain Blue - EM Loads Out 0-10V Dimming Outputs Blue - EM Line In + - + - + - Dimmer 3 Dimmer 2 Dimmer 1. Dimmer 3 Dimmer 2 Dimmer 1. + - + - + - 0-10V Dimming 2 Mounting Mounting Low Voltage Line Voltage (Class 2). Mount the Room Controller above the entrance door of the room being controlled. Adjustable Skylights 6. Purple - Load 3 Out Adjustable Skylights White Red - Load 2 Out Switchpack QuickConnect Cables Receptacle CAUTION: Bonding between conduit connections is not automatic and must be provided as part of the installation.

8 Red BMS/Out 5. Black Sensors Green Sensors Slider Station Integration Controls Connect any necessary line and low voltage conduit directly 4. Yellow - Load 1 Out Wallstations Blue - Load In A/V - Integration Controls Mode +. Demand - Response Alert Mode +. - +. 3. Time - to the Room Controller . Clock +. 2. White/Orange - 277V N. White/Black - 120V N. Black - Line In 1. Energy Options DIP Switch High End Options Demand Response Occupancy Not Used Energy 1 2 3 4. Default 10% Occ Reset 20% Vac (default). 30%. Low End 40%. Status Adjustment 0-10V Gain Blue - EM Loads Out 0-10V Dimming Outputs Blue - EM Line In + - + - + - Dimmer 3 Dimmer 2 Dimmer 1.

9 Dimmer 3 Dimmer 2 Dimmer 1. - - - Emergency + + +. 0-10V Dimming Line Voltage (RC3DE only). Load Wiring CAUTION. Before Connecting Circuits: 1. Connect lighting load wiring directly to the circuit breaker to ensure there are no shorts or miswires. 2. For any 0-10V dimmable loads, separate the purple and gray leads for each zone controlled. All lighting loads should be at full bright output. 3. Isolate one dimming zone and temporarily connect the purple and gray 0-10V leads together. 4. Verify that the controlled zone dims to its lowest output level, then label the zone wiring for easy identification.

10 Disconnect the 0-10V leads for the zone under test and then repeat for remaining dimming zones. ALL MODELS Note: All provided wiring leads Neutral Line In are #14 AWG wiring. (120V or 277V) Wire connections should White/Black = 120V Neutral be rated suitable for the White/Orange = 277V Neutral Cap OFF all Unused Leads wire size employed. Connect Neutral for Appropriate Voltage. OR. Blue = Room Line In Black = Power Supply Line In Yellow = Load 1 Out Load 1. Load Neutrals Adjustable Skylights Red = Load 2 Out 6. Purple - Load 3 Out Adjustable Skylights White Red - Load 2 Out Switchpack QuickConnect Cables Receptacle CAUTION: Bonding between conduit connections is not automatic and must be provided as part of the installation.