S1/1 S1/1 ROVER V8 ENGINE P ARTS - Real Steel

1 CYLINDER BLOCK TRAIN AND V8 ENGINE PARTSS1/1S1/1 ARP Main Bearing engines [10] & non-crossbolted & engines Studs Extra LongARP Main studs are manufactured from aircraft quality 8740 chromemoly Steel . Tensile strength of 190,000 psi. At " length, this allowsfor the addition of a stud girdle or long stud- " for stud for stud Block AreaCylinder Block Plugs/Dowel and TapCX954 Main core plug (8) oil gallery plug (4) threaded gallery plug (2) core plug over cam (1) block drain tap for cyl block top face size 77 Cam Bearing a performance ENGINE , studs are best.

2 They eliminate main cap walk& fretting, as well as protecting the threads in the block. The studs aremanufactured from 8740 chrome moly. they have a 200,000psi tensilestrength, & the threads are rolled. Torq- 135 lb ft with oil, 90 lb ft withARP Stud KitCX221 Cross bolt-hex head uses qty 9. 1999-03 uses qty 8CX224 Cross bolt-allen head uses qty 1. 1999-03 uses qty bolt Dowty washers (8/9) bolt Dowty washers (1/2) FOR CROSSBOLTED BLOCKI ssue 106 Real Steel Tel: 01895 440505e-mail.

3 AreaBig End Bearings onlyMade by Federal Mogul [Sealed Power] in the big ends only big ends only End Bearings [made in the USA]CX2104 Std big ends only-Clevite " big ends only-Clevite * " big ends only-Clevite * " big ends only-Clevite Bearing Sets [made in USA]CX2124 Std mains only-Clevite " mains only-Clev " mains Fed Mogul Bearings-extra- plain shellsLate made in USAOn cylinder blocks where there is only one centre main crankshaft thrust[upper], instead of upper & lower, an extra- plain shell, for the centremain cap, will be required.

4 Applies to very late , & mains- extra plain shell mains- extra plain shell bolts are forged from 8740 chrome moly. The threads are rolledafter heat treatment. In the High Performance Series, they have a nominalrating of 180,000psi. kits include hardened washers.* See P2- ROVER V8-Crankshaft AreaAZ780 Cloyes Race Billet True Roller set : Induction heat-treated, Billet Steel gears, 9 keyway crankgear allows +/- 8 degrees. Adjustability in 2 crank degree True-roller chain with.

5 250 rollers. Hand matched to qualifyboth centre distance & chain for AZ780 Street True-Roller set : Cast iron cam gear, Induction heat treated, billet Steel crankgear [3 keyways], True-roller chain with .250 rollers. Made in chain for BY9-1132 timing set [3 pieces] kit is for early engines with gear type oil pump in timing chain for std timing set Timing Chain Sets and PartsCX2074 For 4 spd and Range ROVER SD1 Manual 5 spd, thick wall Disc/short nose long key KeyCrankshaft Spigot BushesAZ215 ARP Hi-Performance kit comprises of bolts and nuts forged from 8740 Chrome strength of 190.

6 000 nut- eaCX3000 Standard bolt End Bearings-4ltr & onlyCX2555 Std big ends only " big ends only big ends only Bearing Sets-4 litre and onlyCX2560 Std mains only " maind only crank sizes: " " // crank sizes:Mains. " " // Rod Bolts and NutsReal Steel Tel: 01895 440505e-mail: in/5l STROKER CRANKSHAFT- 4998ccDW49951 Stroker crank-cast blk crank has a stroke of . Used with a bore of , thecapacity will increase to 4998cc. Crank must be used with narrowedSBC small journal conrods, as the big end journals are wider thanstandard.

7 Nitrided & crossdrilled. Long nose. Small diameter mainsfor cylinder blocks. 2 big end journals. Weight = Madein for litre EnginePistons for OEM EngineRings for litre EngineCX2492+.020" pistons, :1 comp originally on the ROVER Vitesse. Use with ring set Pistons & PinsSet of 8 pistons with pins included [ " / bore] +.020" :1 comp* +.020" :1 comp* * with cylinder heads. Use with rings AZ3920 Cast Pistons & PinsSet of 8 pistons with pins included [ " bore]Cast Pistons & PinsSet of 8 pistons with pins included [ " / bore] DW4620 +.

8 020" :1 comp* * with cylinder heads. Use with rings AZ4620 Ring Sets for Pre-SD1/R/ ROVER pre 1976 "Comp:5/64"Oil:3/16"DW884 Cast rings standard rings +.020" Sets for SD1/R/ ROVER 1976 onBore: "Comp: 1/16"Oil: 3/16 DW889 Cast rings standard cylinder only-as above entry chrome faced rings +.020" cylinder only-as above entry SPACERDW525 Spacer-use with long crank spacer is needed when a long nose crankshaft like a used with the early timing cover with the gear type oilpump.

9 Otherwise the end of the crank protrudes past the endof the harmonic balancer.* Bearings on page 1 with an asterisk are now- AS bi-metal shells are marked with a suffix A . These bearings are ofthe aluminium, tin, silicon Bimetal type of material and offer the ENGINE builder an OE type of bearing for enginesgoing into standard duty ROVER V8 -Crankshaft/Camshaft and Valve Train AreaRings for OEM Sets for OEM EnginesAZ3905 Chrome rings std bore rings std (1cyl) rings +.020" rings +.

10 020" (1cyl) "[94 ]Comp: : 3mmRing Sets for OEM EnginesAZ4605 Chrome rings std bore rings +.020" oversize "[94mm]Comp: : 3mmCamshaft/Valve Train AreaAZ754 STANDARD Hydraulic Camshaft for most long nose engines HURRICANE Hydraulic Camshaft for most applications, including automatic transmission. Worth an extra 20hp over a std ENGINE . If the cylinder block and cylinderhead faces have not been heavily machined, and the valve guides are fitted to the correct length, then this cam should bolt straight Range@.