SAFETY DATA SHEET - LPS Labs

1 SAFETY data SHEET1. IdentificationLPS Belt DressingProduct identifierOther means of identification02216 Part NumberA non-chlorinated, non-drying, water resistant spray dressing for extending the life of rubber drivebelts by improving traction and allowing runs under reduced belt useNone restrictionsManufacturer/Importer/Suppli er/Distributor informationManufacturerManufacturerCompa ny nameITW Pro BrandsAddress4647 Hugh Howell , GA 30084 Country( )Tel: +1 770-243-8800In Case of Emergency1-800-424-9300 (inside )+001 703-527-3887 (outside Hazard(s) identificationCategory 1 Flammable aerosolsPhysical hazardsLiquefied gasGases under pressureCategory 2 Skin corrosion/irritationHealth hazardsCategory 3 narcotic effectsSpecific target organ toxicity, single exposureNot hazardsNot defined hazardsLabel elementsSignal wordHazard statementPrecautionary statementPreventionResponseStorageDispos alHazard(s) not otherwiseclassified (HNOC)Supplemental informationDangerExtremely flammable aerosol.)

2 Contains gas under pressure; may explode if heated. Causes skin irritation. May cause drowsiness or away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Avoid breathing gas. Wash thoroughly after handling. Use only outdoors or in a well-ventilated area. Wear protective on skin: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. If inhaled: Remove person to fresh air and keep comfortable for breathing. Call a poison center/doctor if you feel in a well-ventilated place. Keep container tightly closed. Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 C/122 of contents/container in accordance with local/regional/national/international / 9 Material name: LPS Belt Dressing02216 Version #: 02 Revision date: 12-29-2016 Issue date: 08-10-2015 SDS US3.

3 Composition/information on ingredientsMixturesCAS numberCommon name and synonymsChemical name%142-82-5 Heptane40 - 5068476-86-8 Petroleum Gases, Liquefied,Sweetened40 - 509003-29-6 Polybutene (Isobutylene/butenecopolymer)1 - 104. First-aid measuresRemove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISONCENTER or doctor/physician if you feel contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Getmedical advice/attention. Wash contaminated clothing before contactRinse with water. Get medical attention if irritation develops and contactNot likely, due to the form of the product. In the unlikely event of swallowing contact a physician orpoison control center. Rinse cause drowsiness and dizziness.

4 Headache. Nausea, vomiting. Skin irritation. May causeredness and importantsymptoms/effects, acute anddelayedProvide general supportive measures and treat symptomatically. Keep victim under may be of immediatemedical attention and specialtreatment neededEnsure that medical personnel are aware of the material(s) involved, and take precautions toprotect information5. Fire-fighting measuresWater fog. Foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing mediaDo not use water jet as an extinguisher, as this will spread the extinguishingmediaContents under pressure. Pressurized container may explode when exposed to heat or fire, gases hazardous to health may be hazards arising fromthe chemicalFirefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, protective equipmentand precautions for firefightersIn case of fire: Stop leak if safe to do so.

5 Do not move cargo or vehicle if cargo has been exposedto heat. Move containers from fire area if you can do so without risk. Containers should be cooledwith water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hoseholder or monitor nozzles, if possible. If not, withdraw and let fire burn fightingequipment/instructionsUse standard firefighting procedures and consider the hazards of other involved materials. Movecontainers from fire area if you can do so without risk. In the event of fire and/or explosion do notbreathe methodsExtremely flammable aerosol. Contents under pressure. Pressurized container may explode whenexposed to heat or fire hazards6. Accidental release measuresKeep unnecessary personnel away. Keep people away from and upwind of spill/leak.

6 Keep out oflow areas. Many gases are heavier than air and will spread along ground and collect in low orconfined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothingduring clean-up. Avoid breathing gas. Emergency personnel need self-contained breathingequipment. Do not touch damaged containers or spilled material unless wearing appropriateprotective clothing. Ventilate closed spaces before entering them. Local authorities should beadvised if significant spillages cannot be contained. Use personal protection recommended inSection 8 of the precautions,protective equipment andemergency proceduresRefer to attached SAFETY data sheets and/or instructions for use. Stop leak if you can do so withoutrisk. Isolate area until gas has dispersed.

7 Eliminate all ignition sources (no smoking, flares, sparks,or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilledmaterial. Prevent entry into waterways, sewer, basements or confined areas. Absorb in vermiculite,dry sand or earth and place into containers. Following product recovery, flush area with Spills: Wipe up with absorbent material ( cloth, fleece). Clean surface thoroughly toremove residual contamination. For waste disposal, see section 13 of the and materials forcontainment and cleaning up2 / 9 Material name: LPS Belt Dressing02216 Version #: 02 Revision date: 12-29-2016 Issue date: 08-10-2015 SDS USAvoid discharge into drains, water courses or onto the precautions7. Handling and storagePressurized container: Do not pierce or burn, even after use.

8 Do not use if spray button is missingor defective. Do not spray on a naked flame or any other incandescent material. Do not smokewhile using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, orexpose containers to heat, flame, sparks, or other sources of ignition. All equipment used whenhandling the product must be grounded. Do not re-use empty containers. Avoid breathing contact with eyes, skin, and clothing. Avoid prolonged exposure. Use only in well-ventilatedareas. Wear appropriate personal protective equipment. Observe good industrial for safe handlingLevel 3 locked up. Pressurized container. Protect from sunlight and do not expose to temperaturesexceeding 50 C/122 F. Do not puncture, incinerate or crush. Do not handle or store near an openflame, heat or other sources of ignition.

9 This material can accumulate static charge which maycause spark and become an ignition source. Store in a well-ventilated place. Stored containersshould be periodically checked for general condition and leakage. Store away from incompatiblematerials (see Section 10 of the SDS).Conditions for safe storage,including any incompatibilities8. Exposure controls/personal protectionOccupational exposure limitsThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure this time, the other constituents have no known exposure OSHA Table Z-1 Limits for Air Contaminants (29 CFR )ValueComponentsTypePEL2000 mg/m3 Heptane (CAS 142-82-5)500 ppmUS. ACGIH Threshold Limit ValuesValueComponentsTypeSTEL500 ppmHeptane (CAS 142-82-5)TWA400 ppmUS.

10 NIOSH: Pocket Guide to Chemical HazardsValueComponentsTypeCeiling1800 mg/m3 Heptane (CAS 142-82-5)440 ppmTWA350 mg/m385 ppmNo biological exposure limits noted for the ingredient(s).Biological limit valuesGood general ventilation (typically 10 air changes per hour) should be used. Ventilation ratesshould be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,or other engineering controls to maintain airborne levels below recommended exposure limits. Ifexposure limits have not been established, maintain airborne levels to an acceptable level. Eyewash facilities and emergency shower must be available when handling this engineeringcontrolsIndividual protection measures, such as personal protective equipmentWear SAFETY glasses with side shields (or goggles).