SCN60 Installation and Use - Scotsman Homeice

1 IntroductionThis manual includes information for theinstallation, operation and maintenance of theSCN60 residential ice SCN60 was developed to offer fans ofScotsman s Nugget Ice form the ability to have thatice in their homes. Previously Nugget Ice was onlyavailable in commercial establishments, where itdeveloped a strong following because of thechewable nature of the ice. This machine makesauthentic Nugget ice, using the same process asthe larger commercial 2011 Page 1 SCN60 Installation and UseTable of ContentsProduct Description:..Page 2 Cabinet 3 Location Recommendations:..Page 5 Decorating Features.

2 Page 6 Door Panel 7 Door 8 Plumbing - Pump 9 Plumbing: Gravity Drain 10 Electrical and Start 13 How to remove scale from the ice making 14 Outdoor Use Notice:Keep from freezing. Severe damage will occur to the unit if left in or operated in temperatures beyondthe limits listed in this manual. That damage is NOT covered by dry. Do not locate in low lying areas where puddles will Shade: Heat gain from the sun will reduce the unit's ability to make and store ice, andultraviolet radiation from the sun can potentially damage the unit's plastic Supply: Avoid a long run of hose or tubing exposed to the sun.

3 Plastic water supply tubingshould be rated for potable water and include UV protection. Copper tubing is Flow Prevention: The unit includes back flow prevention, no additional check valve is : Do Not drain into swimming pool or onto Description:This ice machine is designed to be used indoors, ina controlled environment or outdoors within SCN60 is made up of two major systems: theice making system and the ice storage system. Theice making system is a continuous flow type icemachine, it makes ice when the ice level becomeslow and stops when it is ice storage system is an insulated chest with adrain at the bottom for melting ice.

4 It is notrefrigerated, insuring that the bin contains fresh InformationDimensions:The cabinet is fourteen and seven eighths incheswide by thirty three and three eighths to thirty fourand three eighths inches and Operational Requirements The SCN60 must be connected to a potablewater supply. The water supply must have a conductivity ofat least 10 microSiemens/cm. Minimum water pressure: 20 psi Maximum water pressure: 80 psi Minimum water temperature: 40 degrees F. Maximum water temperature: 90 degrees is designed to operate in wide range of airtemperatures: Minimum air temperature: 50 degrees F.

5 Maximum air temperature: 100 degrees the machine will function within the listedranges, it works best at water temperaturesbetween 50 and 60 and air temperatures between60 and : Ice making capacity goes down as theenvironmental temperatures go up, and will beseverely reduced at temperatures over a unit outside of the limits can causeproblems that are not covered by the warranty and,if extreme, cause damage to the QualityThe water to the machine must be potable, or fit forhuman consumption. Beyond that, water suppliesvary in the degree of mineral content. As this icemachine makes ice, all the water that flows into themachine is changed into ice.

6 That includes anyminerals that might be in the water. However,during ice making some minerals will stick to theice making components. The higher the mineralcontent, the more mineral build up will occur. Waterfilters are a partial help, as they will remove thesuspended solids, but water treatment is neededfor the dissolved solids, which are part of the waterand cannot be filtered WaterThis machine can be supplied with ReverseOsmosis water, but the water conductivity must beno less than 10 reverseosmosis system should include post treatment orblending to satisfy the water s water is not recommended and coulddamage the water softeners exchange one mineral foranother.

7 Softened water may not improve waterconditions when used with ice machinesElectrical powerThe unit must be on its own 115 volt, 60 Hz, 15amp circuit. It is equipped with a power cord andcan be plugged into a nearby outlet. Extensioncords are not allowed by most codes. Follow allapplicable InformationWarranty information is supplied separately fromthis manual. Refer to it for coverage. In general, thewarranty covers defects in materials orworkmanship and does not cover corrections ofinstallation errors or 2011 Page 2 SCN60 Installation and UseCabinet DimensionsMay 2011 Page 3 SCN60 Installation and UseScotsman Ice Systems are designed and manufactured with the highest regard for safety andperformance.

8 They meet or exceed the standards of agencies like assumes no liability or responsibility of any kind for products manufactured by Scotsman thathave been altered in any way, including the use of any parts and/or other components not specificallyapproved by reserves the right to make design changes and/or improvements at any time. Specificationsand designs are subject to change without 7/8"AIR INAIR OUT3/4" SHEET METAL DOOR FRONT - IF DOOR KIT MIN. CABINET DOOR22"29 1/4"1" LEG ADJUSTMENT(4) PLACES2 3/4"2 3/8" DOOR KITAND HANDLE3/4"4"33 3/8" 3/8" SIDE PANEL2 1/2"7 1/2"3 1/4"2 3/4"5 1/8"11 5/8"115 VPOWER CORDDRAIN ACCESS - FLEXIBLE TUBING3/8" PUMP MODEL (INCLUDED)5/8" GRAVITY MODEL (NOT INCLUDED)1/4" COPPERWATER INLETCOMPRESSION FITTING PROVIDED3 7/8"20 3/8"FLOOR DRAINACCESS HOLEL ocation Recommendations:The machine can be built into a cabinet.

9 It is an aircooled refrigeration system and so air flows in andout of it through the grill at the bottom front. Thegrill must not be blocked by any covering door orother are two models, one is a gravity drain typeand it must have a building drain connection belowthe level of the drain tube at the back of thecabinet; the other is a pump drain model which canforce drain water up a maximum of 10 feet,allowing it to be located where a gravity drain isn Extension:In some situations the leglevelers will be extended enough to become kit to extend the kickplate over the legs Stability: In some free standinginstallations it may be prudent to add a bracket thatsecures the back of the cabinet to a wall.

10 That kitnumber Conversion: A gravity drain model can beconverted to a drain pump model by installing adrain pump kit. The drain pump kit consists of adrain pump, wiring harness and associated part number NotesBuilt In Situations: If a finished floor is to beinstalled in the area after the ice machine has beenbuilt in, shims the expected thickness of the floorshould be installed under the unit to keep themachine level with the planned floor : The water connection is at the back and addsa few inches to the cabinet depth. Minimumclearance is 0 in. at the top, 2 in. at the rear and1/8 in.