Series MMV Triple Listed! ASSE 1017, ASSE 1069 & ASSE …

1 For Residential, Commercial and Institutional ApplicationsES-MMVJob Name Contractor Job Location Approval Engineer Contractor s No. Approval Representative Series MMVT hermostatic Mixing ValvesSizes: 1 2" 1" (15 25mm) Series MMV Thermostatic Mixing Valves maintain and limit mixed hot water to a desired, selectable temperature. The MMV Series can be set to any temperature between 80 F and 120 F with flow rates as low as gpm and as high as 12 gpm (refer to capacity chart on back). This mixing valve Series is listed under asse 1017 for valves used in hot water source applications, asse 1069 for single-pipe, tempered water applications and asse 1070 for valves used in individual or multiple fixture applications and also listed IAPMO cUPC.

2 The MMV-M1 uses a double throttling design to control both the hot and cold water supply to the mixed outlet. The superior flow characteristics of this valve provide accurate temperature control ( 3 F) with low pressure drop across the rated flow range. As an added feature, the MMV-M1 Series incorporates integral inlet filter washers and check valves in both the hot and cold water inlets to protect against cross flow. The MMV-M1 is available with either union thread (-UT), union solder (-US), CPVC, (-QC) Quick-Connect or PEX end Bronze body construction Solid wax hydraulic principle thermostat assures dependable mixing of hot and cold water Thermostat controls both hot and cold water Solder, threaded, PEX or CPVC, Quick-Connect end connection models available Adjustment cap with locking feature asse 1017 listed asse 1069 listed asse 1070 listed IAPMO cUPC listed Integral filter washers and check v alvesSpecificationsA Thermostatic Mixing Valve shall be installed on the hot water supply to fixture.

3 The valve shall be asse 1017, asse 1069, asse Standard 1070 and IAPMO cUPC listed and control the temperature of the hot water. It shall have a bronze body and shall include integral filter wash-ers and check valves and an adjustment cap with locking feature. The valve shall be provided with solder (-US), threaded (-UT), CPVC, (-QC) Quick Connect or PEX union connections. The valve shall be a Watts Regulator Company Series MMV-M1 Thermostatic Mixing Valves are ideal for supplying sinks, baths, showers or lavatories with tempered water. The MMV-M1 valves can be used in residential, commercial and institutional environments. These thermostatically modulated mixing valves can be used anywhere preset water temperature is required for point-of-use installations such as in homes, schools, restaurants, hospitals, beauty salons, and public restrooms. The MMV-M1 is provided with an adjustment cap that includes a locking MMV-M1 valves should be used prior to the fixture to reduce the hot water supply to a safe !

4 When used in an asse 1017 application at the hot water source, the Watts Thermostatic Mixing Valve Series MMV cannot be used by itself to control final temperature at fixtures where asse Standard 1016-96 or asse Standard 1070 listed devices are required. Such use may result in severe bodily injury ( scalding or chilling) and/or death. Additional asse Standard 1016-96, asse 1069 or asse Standard 1070 listed devices, such as Watts Series L111, USG or MMV, should be used at fixtures to prevent possible systems should recirculate water at temperatures over 140 F to reduce the risk of bacterial growth in the piping. This valve should not be used to achieve these elevated temperatures. This valve can be used at fixtures in conjunction with recirculation systems to reduce the system s hot water to a safe temperature at the point of !Water temperatures in excess 110 F (43 C) are dangerous and may cause scalding, severe injury or death!

5 This valve can be adjusted to deliver water at temperatures exceeding 110 F (43 C). Consequently, when used in an asse 1016-96, asse 1069 or asse 1070 application, the installer must check the mixed water outlet temperature at the point of use and adjust the Watts Thermostatic Mixing Valve Series MMV to ensure delivery of water at a safe temperature not exceeding 110 F (43 C). Mechanical valves are not fail-safe. Due to the effects of various water condi-tions, periodic verification of outlet water temperature is listed ! asse 1017, asse 1069 & asse 1070 Watts product specifications in customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently : BronzeDisc: Stainless steel Thermostat Assembly: CopperO-rings: Buna-N; EPDMP istons: Udel-P1700 Springs: Stainless Steelpressure Temperature Flow RateMinimum Supply Pressure Static: 30psi (207 kPa)Inlet Temperatures: hot inlet, 120 F 180 F (49 C 82 C), cold inlet, 39 F 85 F (4 C 29 C)Hot Water Inlet to Outlet Differential Temperature: 5 F (3 C) above set pointTemperature Out: Field range: 80 F 120 F (27 C 49 C), adjust-able.

6 Accurate within 3 F ( C)Maximum Temperature: 200 F (93 C)Maximum Pressure: 150psi ( bar)Minimum Flow: gpm ( lpm) @ ( kPa) Maximum Flow: 20 gpm (76 lpm) @ 125psi (862 kPa) Max. Pressure Differential between Hot & Cold Water Supplies: 25%Listing: asse 1017, asse 1069, asse 1070 and IAPMO cUPC When tested in accordance with asse 1017, asse 1069 & asse ConstructionINLET FILTER WASHERC apacity* kpa psi 345 50 276 40 207 30 138 20 69 1000 2 4 6 8 10 12 14 gpm 15 23 30 38 46 53 lpmPressure DropFlowFlow curves are for reference. Actual flows may vary depending on system temperatures and/or pressures.*Flow curve with integral inlet filters and check valvesBUTTON HEAD SCREWLOCKING ADJUSTMENT CAPADAPTERO-RINGSTEM ASSEMBLYO-RINGO-RINGPLUNGERSEATSPRINGTHE RMOSTATFUNNELUNION NUTTAILPIECECHECK MODULEBODY SIZE (DN) MODEL DIMENSIONS WEIGHT A B C D in. mm in. mm in. mm. in. mm in. mm lbs. kg.

7 1 2 15 47 8 124 57 16 137 33 16 80 1 2 13 .68 3 4 20 MMV-UT-M1 47 8 124 57 16 137 33 16 80 9 16 14 .73 1 25 55 16 135 55 8 143 33 8 86 11 16 17 .73 1 2 15 413 16 123 53 8 137 31 8 80 1 2 13 .68 3 4 20 MMV-US-M1 55 16 135 55 8 143 33 8 86 3 4 19 .73 1 25 513 16 148 57 8 149 35 8 92 15 16 23 .73 1 2 15 51 4 133 59 16 142 35 16 85 5 8 1 .68 3 4 20 MMV-PEX-M1 51 2 140 511 16 145 37 16 88 3 4 19 .73 1 25 57 8 149 57 8 150 35 8 93 13 16 2 .73 1 2 15 43 4 121 55 16 136 31 16 79 1 2 13 .68 3 4 20 MMV-CPVC-M1 51 4 133 59 16 142 35 16 85 3 4 19 .73 1 25 511 16 144 513 16 147 39 16 90 15 16 23 .73 1 2 15 65 8 168 61 4 159 4 102 11 2 38 .98 3 4 20 615 16 177 67 16 163 43 16 106 111 16 42 1 25 71 8 181 61 2 165 41 4 108 13 4 44 M1 MMV-CPVC-M1 MMV-QC-M1 BONNET ASSEMBLYFILTER WASHERFIBER WASHERTHREAD (UT)SWEAT (US)CPVCPEXDDDDQUICK-CONNECTQC'D'DDimens ions WeightsABCHot Water InletMixed OutletCold Water InletES-MMV 1004 2010 WattsUSA: 815 Chestnut St.

8 , No. Andover, MA 01845-6098; : 5435 North Service Rd., Burlington, ONT. L7L 5H7; Watts Water Technologies Company