Example: marketing
SG400NA / SG400EU SG800NA / SG800EU - …
v20150210 User Guide SG400NA / SG400EU SG800NA / SG800EU This User Guide provides information and instructions related to the printer hardware.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
SG400NA / SG400EU SG800NA / SG800EU
www.sawgrassink.comAug 30, 2012 · SG400NA / SG400EU SG800NA / SG800EU This User Guide provides information and instructions related to the printer hardware. Visit sawgrassink.com for more information and to download the printer software and related instructions.
SUBLIMATION HEAT PRESS SETTINGS - QUICK …
www.sawgrassink.comfollowing manufacturer guidelines, ng place. Producing quality end products is a matter of SUBLIMATION HEAT PRESS SETTINGS - QUICK REFERENCE GUIDE
QUICK REFERENCE GUIDE SUBLIMA TION HEAT PRESS …
www.sawgrassink.comSUBLIMA TION HEAT PRESS SETTINGS QUICK REFERENCE GUIDE Surface Press Time Temp Pressure Tips/Comments Polyester Fabric 35-40 seconds 400° F 40 psi (medium) Pre-press shirt for 3-5 seconds to eliminate moisture. Tack spray transfer and use blow-out sheet to avoid ghosting Vapor Apparel 45-55 seconds 380-390° F 40 psi (medium) See vaporapparel ...
QUICK REFERENCE GUIDE SUBLIMA TION HEAT PRESS …
www.sawgrassink.comsubstrates, a calibrated heat press, smart color management, following manufacturer guidelines, testing and practice! If you are having difficulty or the substrate is not listed below, contact your reseller or the substrate manufacturer for their specific recommendations.
Table of Contents | i
www.sawgrassink.comWarm air from the vent is normal and not a cause for concern. Do not leave the top or right front cover open. If you do, dust or other matter might get inside the printer, and this will reduce print quality. During printing, do not move the printer or open its covers. Do not open the top or right front cover during p rinting.
Related documents
Cascade2 - Arc Systems
www.arcsystems.bizCARVE CASCADE RAPIDE INSTALLATION AND USER INSTRUCTIONS Leave these instructions with the appliance ISTRUZIONI PER EINSTALLAZIONE E FUSO Lasciare queste istruzioni ...
31-31560 EN v09 - GEAppliances.ca
specs.maberendezvous.caPREPARE HOT WATER LINE NOTE: GE recommends copper tubing for the water line, but if • The water supply line (3/8” copper tubing or flexible braided hose) may enter from either side, rear or floor within the
Well Protector Dry Pellet Chlorinator - Water …
www.water-research.net3 Installation Mounting the Chlorinator (Refer to Figure 1) Installing the casing mount to the well. 1. Attach the chains (Item 1) to the casing mount bracket (Item 2) using 5/16 - 18 x 3/4" long cap
Single Rear Drive Axles, Rear-Rear Tandem Drive …
graphicvillage.orgMaintenance Manual 5A Single-Reduction Differential Carriers Single Rear Drive Axles, Rear-Rear Tandem Drive Axles and Front Drive Steer Axles Revised 02-18
IM EASY FAST SMART GB 0 old - LPG Trade
www.lpgtrade.com5. 2.0 CONNECTION OF THE INJECTORS CUT-OFF WIRING. Verify the polarity of the injectors acting as follows: 1 Disconnect all connectors of the original injectors,
Head of Electrical Engineering - ogcrecruitment.com
www.ogcrecruitment.comJOB DESCRIPTION Head of Electrical Engineering Page 2 of 4 Doc #: XXX-XXX-#### Rev #: V1.0 Date: 30-06-2016 Competencies Maintenance & Turnaround Management System :