Slotted Spring Pins Design Guide - SPIROL
equipment to the highest quality standard. • SPIROL is a direct supplier to the brand OEM automotive companies as well as to other tier 1 and 2 companies in the automotive industry and is fully versed in the high standards and demands of that industry. • SPIROL is the only company that standardizes and inventories both metric and imperial ...
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Slotted Spring Pins Design Guide - SPIROL
www.spirol.comSTANDARD SIZES Nominal Pin Length Length Tolerance Length Tolerance - ISO 8752 4mm to 10mm ± 0.25mm 12mm to 50mm ± 0.50mm 55mm to 100mm ± 0.75mm Length Tolerance - DIN 1481 (Ref) 4mm to 10mm + 0.5mm 12mm to 50mm + 1.0mm 55mm to 100mm + 1.5mm METRIC SPECIFICATIONS Only available in high carbon (B) and austenitic stainless steel (D)
ISO 8752 EN 28752 - SPIROL International …
www.spirol.comD1 D2 D3 Pins with diameter ≥10mm may be supplied with a single chamfer configuration. B is less than nominal diameter LENGTH D C S B METRIC SPECIFICATIONS ISO 8752 EN 28752 ...
Geschlitzte Spannhülsen - spirol.com
www.spirol.com2 D1 D2 D3 Spannhülsen mit Durchmesser ≥ 10mm können mit einer Anfasung geliefert werden. B ist kleiner als der Nenndurchmesser LÄNGE D C S B ISO 8752 EN 28752 STANDARDLÄNGEN IN MM
SPIROL Compression Limiters Design guide
www.spirol.com2 It is imperative that the proper Compression Limiter be designed into each application based on the specific requirements for that assembly, and that the plastic host be designed appropriately to ensure that bolted
Compression, Limiters, Spirol compression, Spirol, Compression limiter
ASME B18.8.2 LENGTH D C - SPIROL International …
www.spirol.comTitle: ASME B18.8.2 Slotted Pins Author: SPIROL Subject: SPIROL Slotted Spring Pins offerings to ASME B18.8.2 specifications. Keywords: slotted spring pins; B18.8.2 ...
Press-In Series 50 and 51 Inserts - SPIROL
www.spirol.comTitle: Press-In Series 50 and 51 Inserts Author: SPIROL Subject: Dimensional data for SPIROL's Press-In Inserts for Plastics Keywords: SPIRIOL, press in, brass inserts, specifications, dimensional data
Series, Plastics, Insert, Spirol, Series 50 and 51 inserts, Inserts for plastics
INSERTS FOR PLASTICS - SPIROL International Corporation
www.spirol.comINSERTS FOR PLASTICS. Cover2 Plastic Insert Bolt Friction Force Force L Torque ... The objective is to design an Insert with sufficient torque resistance to accommodate the tightening torque necessary to achieve sufficient axial tension load on the threaded joint to keep it together and prevent loosening,
INSERTS FOR PLASTICS
www.spirol.comthe installation torque requirements to achieve a good threaded joint, and the pull-out values that meet the application load requirements. Helical knurls are the designer’s choice to maximize the torque resistance for a given diameter. The volume of these knurls must be such that sufficient
Disc Springs - SPIROL
www.spirol.comOther factors such as the required life, the working temperature, and environmental conditions that may require corrosion protection or cleanliness requirements all will contribute to actual fatigue life and need to be taken into account. Design to Minimize Stresses: The fatigue life of a Disc Spring is directly related to the magnitude of stresses
SPIROL Compression Limiters Design guide
www.spirol.comThe recommended torque values to produce this clamping load are provided on page 4. Determination of Compression Limiter Length Proper length specifications of both the Compression Limiter and the plastic component are crucial to the proper performance of the bolted joint. The recommended
Related documents
AWI Standard for Architectural Wood Casework
www.gotoawi.coma) This standard is written with the metric system of measurement followed by the U.S. Customary System of measurement in brackets. b) The system of measurement used in the project’s original contract documents and architectural drawings will dictate which system of measurement within these standards is used for verification of compliance.
Standards, Woods, Architectural, Metrics, Casework, Architectural wood casework
American Softwood Lumber Standard - ALSC
www.alsc.orgcess and in the public interest, standard sizes (both in metric. 1 and conventional units) and gen-eral requirements for developing grades of soft-wood lumber. It is implemented through an in-ternationally recognized accreditation and certi-fication program, the purpose of which is to pro-
TR Hank Rivet Bushes - Farnell
www.farnell.comMetric Dimensions Hank-Loc® version available Please note: Hank-Locking is a process applied to our standard rivet bush ranges giving them a locking feature Example of the Hank-Loc® feature: 2 www Preferred Range Metric Dimensions …
Torque-Tension Relationship for Metric Fasteners
www.fastenal.comMicrosoft Word - Metric Torque _Mar 6 2009_.doc Author: kmenke Created Date: 3/6/2009 4:49:32 PM ...
TECHNICAL DATA MQ-7 GAS SENSOR - SparkFun Electronics
www.sparkfun.comStandard circuit: As shown in Fig 2, standard measuring circuit of MQ-7 sensitive components consists of 2 parts. one is heating circuit having time control function (the high voltage and the low voltage work circularly ). The second is the signal output circuit, it can accurately respond changes of surface resistance of the sensor. V H Vc
Metric Stainless steel Torque Mar 6 2009 - Fastenal
www.fastenal.comTorque Values for A2 or A4 Metric Stainless Steel Fasteners Bolt Dia (mm) Dry Lubricated 3 1.0 0.9 8.9 in-lbs. 8.0 in-lbs. 4 2.6 2.3 23.0 20.7 5 5.1 4.6 45.1 40.6 6 8.7 7.8 77.0 69.3 8 21.2 19.1 188 169 10 42 38 372 335 12 73 66 54 ft-lbs. 48 ft-lbs. 14 118 106 87 78 16 180 162 133 119 18 258 232 190 171 20 370 333 273 246 22 485 437 358 322 24 ...