Solicap M FTI55, FTI56 (Operating Instructions)

1 BA300F/00/ InstructionsSolicap M fti55 , FTI56 Capacitive Level Limit SwitchBrief overview2 Brief overview!Note! These operating instructions describe the installation and initial commissioning of the level measuring device. It considers all of the functions that are necessary for a usual measuring quick and easy commissioning:Safety instructionsExplanation of the warning symbolsFor special instructions , refer to the corresponding location in therespective chapter. The priority is indicated by the Warning #, Caution " and Note symbols !. Page 6 InstallationThis section describes the required steps when installing the deviceand the installation conditions (such as dimensions).

2 Page 14 WiringThe device is shipped, for the most part, completely wired and ready to plug in. Page 32 Display andoperating elementsThis section provides an overview of the arrangement of the display and operating elements of the device. Page 42 CommissioningThe "Commissioning" chapter shows you how to switch on the device and check its functions. Page 44 TroubleshootingIf faults occur during operation, use the checklist to find the section lists measures you can take yourself to remedy any faults that may occur. Page 61 Brief overview3 Brief operating instructionsBA300F0en0112 1121113113 +S +SNivotesterNivotesterFTC325 3-WIREFTC3253-WIRE12 3123(+)(+) ++11112112z4d2z4d2 PFMPFM1212 FTC325 FTC325 FTC625 FTC625 FTC470 ZFTC470 ZFTC471 ZFTC471 ZNivotesterNivotesterEEx iaEExia1212 FEIFEI5555 FEIFEI5353 U 1U ++12 3123L+L+L L (+)(+) VU (DC)(DC).

3 U~ VU~ VU (AC) /(AC)/(DC)(DC)L1L1L+L+aaNONOaaNONOuuCCuu CCrrNCNCrrNCNCNNL L PEPE(Ground)(Ground) probeallprobe2. Connect power overview44. Configuring the device and switching on the power supplyFEI52, FEI54, FEI55 Green LEDs ( operational status - flashing) Red LED ( fault message) Yellow LED ( switching status) Key ( ) Key (+) Mode switch (position 1-8) 1 : Operation 2: Calibration (empty/full) 3: Switchpoint adjustment 4: Measuring range setting s mode/build-up mode 5: Switching delay 6 : Self-test 7: Fail-safe mode (MIN/MAX) 8: Configuration/upload, downloadBA300 Fxx003!

4 Note! To execute the various functions, press and hold the key for at least 2 , FEI57S Green LED ( operational status) Red LED ( fault message) DIP switch (left), Standard: If the measuring range is exceeded no alarm is output. : If the measuring range is exceeded an alarm is output. DIP switch (right), span Range 1: 500 pF Range 2: pFBA300 Fxx004--++++--FEI55 FEI558/16mA8 ++ cc s10s24248816 32p1632pff50050016001600ppffofoffonfon11 773355build-upbuild-upactiveactiveOperat ionOperationReset to factoryResettofactorysettingssettingsEmp ty calibrationEmptycalibrationFull calibrationFullcalibrationSwitchpointSwi tchpointadjustmentadjustmentMeasurementM easurementrange, small/bigrange,small/bigTTwo-point controlwo-pointcontrolBuild-up modeBuild-upmodeSwitching delaySwitchingdelayMinimum/Minimum/maxim um failsafemaximumfailsafeDevice self testDeviceselftest(Proof test)(Prooftest)

5 Presspressforforup-loadup-loadpresspress forfordown-loaddown-loadModeModeKeyKeyKe yKeypress together forpresstogetherfor20 forpressfor<<press forpressfor<<press togetherpresstogetherpress forpressforMINMIN press forpressforMAXMAXLED SignalsLEDS ignalsFunction/ModeFunction/ModeSymbolSymbolpresspressUp-DownloadUp-DownloadSensor EEPROMS ensorEEPROM press forpressfor>>press forpressfor>>--++ of contents5 Table of contents1 Safety instructions .. Designated use .. Installation, commissioning and operation .. Operational safety .. Safety conventions and symbols.

6 72 Identification .. Device designation .. Scope of delivery .. Certificates and approvals .. Registered trademarks .. 133 Installation .. Overview .. Housing .. Housing heights with adapter .. Process connections and flanges .. Rod probes fti55 .. Rope probes FTI56 .. Installation instructions .. With separate housing .. Probe without active build-up compensation .. Probe with active build-up compensation (under development) .. Installing bracket for wall and pipe mounting .. Post-installation check.

7 314 Wiring .. Connection recommendation .. Wiring in housing F16, F15, F17, F13 .. Wiring in housing T13 .. Connecting the device .. Degree of protection .. Connecting the electronic insert FEI52 (DC PNP) . Connecting the electronic insert FEI53 (3-WIRE) .. Connecting the electronic insert FEI54 (AC/DC with relay output) .. Connecting the electronic insert FEI55 (8/16 mA) . Connecting the electronic insert FEI57S (PFM) .. Post-connection check .. 415 Operation .. Human interface and display elements for FEI52, FEI54, FEI55.

8 Human interface and display elements for FEI53, FEI57S .. 436 Commissioning .. Installation and function check .. Commissioning with electronic inserts FEI52, FEI54, FEI55 .. Commissioning with electronic inserts FEI53 or FEI57S .. 577 Maintenance .. 598 Accessories .. Weather protection cover .. Overvoltage protection HAW569 .. 609 Troubleshooting .. Fault diagnostics in the electronic insert .. Spare parts .. Return .. Disposal .. Firmware history .. Contact addresses at Endress+Hauser .. 6310 Technical data.

9 Input .. Output .. Performance characteristics .. operating conditions: Environment .. operating conditions: Process .. Other standards and guidelines .. Documentation .. 70 Index .. 72 Safety instructions61 Safety useThe Solicap M fti55 and FTI56 are compact capacitive level measuring devices for level limit detection in bulk solids. , commissioning and operationThe Solicap M's state-of-the-art construction meets operating safety requirements and complies with all applicable standards and EU directives. However, if it is used improperly or if it is not put to its intended use, it can be a source of application-related dangers, such as product overflow due to incorrect installation or configuration.

10 Therefore, the installation, electrical connection, commissioning, operation and maintenance of the measuring device only may be carried out by trained specialist personnel authorized by the facility's owner/operator for this purpose. The specialist personnel must have read and understood these operating instructions and must follow the instructions they contain. Modifications or repairs to the device can be carried out only if it is expressly stated in the operating instructions that these are areasIf the measuring system is used in hazardous areas, the corresponding national/federal standards and regulations must be observed.