Solution Alarm System: Solution 6 User Manual

1 Solution -6 Operators ManualPage 1 Electronics Design & ManufacturingPrefaceCongratulations on selecting the Solution -6 security control system for yourinstallation. So that you can obtain the most from your unit, we suggest that you take the timeto read through this Manual and familiarise yourself with the numerous outstanding operatingfeatures of this system . You will notice that in all aspects of planning, engineering, styling,operation, convenience and adaptability, we have sought to anticipate your every possiblerequirement.

2 Operating simplicity and performance have been some of the majorconsiderations and we believe that our objectives in this area have been more than Manual will explain all aspects of the user programming options and operating proceduresfound on the Solution -6 security control panel is microprocessor controlled with one of thehighest degrees of circuit integration ever seen in a security control system . This not only meansmore features but greater reliability and performance.

3 Every feature in this design has beenaccomplished with continual consideration being given to the needs of you, the End the straight forward and uncluttered control console to the simplistic operating method,the Solution -6 is head and shoulders above all others in its class. Listed here are justsome of the many outstanding dynamic battery tester has been incorporated which performs continual testing andmonitoring of the backup battery's condition and will report any failure through the faultindicator on the system Day Alarm feature enables you to monitor the opening of the front door of a shop.

4 Or eventhe opening of a pool situations where the main console is installed in a bedroom and the indicators becomeannoying at night the console extinguish mode, if programmed by your installer, willautomatically turn off all the indicators after sixty seconds. The console indicators will illuminatethe next time a key is pressed or an Alarm 24 Hour zone can be programmed to provide a Fire sound through the connected hornspeakers should an Alarm occur on the 24Hr zone.

5 This feature can be of great benefit whenusing smoke detectors so that a distinctly different alert tone is generated for a fire Design and Manufacturing has injected twenty years of knowledge and expertiseinto the Solution -6 security control panel making it one of the most flexible, tolerantand easy to operate units available on the market today. proves again that anAustralian owned company backed by Australians is by far one of the most technicallyadvanced Alarm equipment manufacturers in the world market place 2 Solution -6 Operators ManualElectronics Design & ManufacturingFeaturesqSix Sector Control battery mode.

6 (Personal Protection)qIntegrated Protection SystemqDay fully programmable Horn speaker Relay, Strobe and Horn Speaker wire, full remote annunciated control interface for EDMSTU or EDM Fail and Fault event Alarm memory Test sectors are fire options stored in via the system Extinguish Radio Key / Keyswitch Operators ManualPage 3 Electronics Design & ManufacturingBasic system OperationThe overall purpose of your Alarm system is to deter any would be intruder from entering leaving your home or office make that sure all the windows and doors are closed.

7 Keyin your designated code followed by the AWAY key. Your Alarm system will now arm andcommence counting down the pre-programmed exit should exit the building during this time closing the exit path on your the exit time expires, a long beep will be heard and any unsealed zones will automaticallybe system is now ready to accept a sealed zone is now opened, a number of pre-programmed events will occur. Following istypical sequence of Alarm system will activate the audible devices such as sirens and horn speakers and willtrigger the strobe light alerting bystanders and yourself when you return.

8 If you have theoptional EDM DIALLER or EDMSTU connected to your system then all relevant Alarm informationwill be transmitted via the telephone line alerting the respective persons of the current siren timer will commence counting down as soon as an Alarm occurs. When this timeexpires the siren will be automatically turned off and placed into a ready state for the your return, the strobe light will still be operating to inform you that there has been analarm and that care should be taken when entering the entering the building one or a number of zone indicators will be flashing allowing you toidentify which particular zone(s)

9 Caused the Alarm next time the Alarm system is armed the indicators will be automatically is a very basic outline of the general system operation. As there are many featuresavailable in your Solution -6, there could be numerous variations from the installer will be able to explain the exact operation of your particular 4 Solution -6 Operators ManualElectronics Design & ManufacturingQuick Reference GuideArming in AWAY mode. + or + or0 + Arming in STAY mode. + or + or 0 + Disarming from AWAY or STAY mode.

10 + or + Manually Isolating Zones. + + + Toggle Day Alarm On/Off. + 7 Trigger Panic the and the keys Duress Alarm . + 9 when system is + 9 when system is Operators ManualPage 5 Electronics Design & ManufacturingControls & IndicatorsThe ConsoleThe console is the communications interface between you and your Alarm system . Itallows you to issue commands and offers both visual and audible indications that guideyou through the general IndicatorsThe system has a number of indicators fitted to the operating console which are capable ofindicating a number of different situations.