Example: air traffic controller
SPECIFIC REGISTRATION REQUIREMENTS FOR FOR …
Supply of aluminum, steel, steel alloy and timber structural components, metal scaffolds. SY11 Petroleum Products Supply of all petroleum products and by-products including lubricants, bunker oil, diesel, gasoline and greases. Equivalent synthetic product suppliers can also be considered for registration. SY12
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Design Guide on Use of Structural Steel
www.bca.gov.sgC.1.1 British/European standards on design of steel structures 62 C.1.2 British/European standards on steel materials 62 C.1.3 British/European standards on manufacturing tolerances 63 C.1.4 British/European standards on bolting assemblies 64 C.1.5 British/European standards on welding consumables 65
Issued by the Commissioner of Building Control under ...
www.bca.gov.sgto be used with the adoption of the Eurocodes New Annexes a) Addition of Annex A – Structural design standards based on the Eurocodes and the corresponding Singapore National Annexes. b) Addition of Annex B– Comparative list of Singapore/British standards and their equivalent Singapore/European Standards. 14 Ver 6.0 Section M
Chapter 3 DESIGN CONCEPT FOR PRECAST SYSTEM
www.bca.gov.sgChapter 3 DESIGN CONCEPT FOR PRECAST SYSTEM ... considerations that the formwork cost for construction on grade is negligible, and the extent of in-ground services will, in general, be substantial. ... manufactured separately using materials such as precast concrete, GRC, Aluminium or steel.
6. INSTALLATION - Building and Construction …
www.bca.gov.sg25 It is essential to identify location of openings, mechanical and electrical (M&E) services, and other fixtures before installation of drywall.
PUBLIC SECTOR STANDARD CONDITIONS OF …
www.bca.gov.sgContents/3 (Seventh Edition July 2014) 14 Time for Completion 14.1 Contractor to Complete on Time 21 14.2 Extension of the Time for Completion 21
ON TO NEW CHALLENGES - Building and Construction …
www.bca.gov.sgWe shape a safe, high quality, sustainable and friendly built environmentMAY 2017 ON TO NEW CHALLENGES ESCALATING MATTERS BCA GALLERY REOPENS NURTURING GREEN ADVOCATES DR JOHN KEUNG REMINISCES ABOUT HIS TIME AS BCA CEO
6. Common Defects
www.bca.gov.sgand alkyd resins, which are easily affected by light, heat or environmental contaminants • Use non-yellowing paints • Prepare surface and repaint with non-yellowing paints Saponification • Use of alkyd-based paints on cement based materials. …
1. Introduction
www.bca.gov.sg1. Introduction In a survey conducted by BCA in year 2003 involving about 10,000 private residential units, water seepage through external walls was found to be a common defect faced by homeowners. The survey findings also showed that the use of single layer brickwall is the most common cause of water seepage through external walls.
STRATA MANAGEMENT GUIDE : 3
www.bca.gov.sgBuilding Maintenance and Strata Management Act Building Maintenance (Strata Management) Regulations 2005 Managing Agent Management Corporation Strata Title Management Corporation Subsidiary Proprietor AGM BMSMA BM(SM) REGULATIONS MA MCST MC SP Preamble This series of Strata Management Guides published by the Building and …
Solar Photovoltaic (PV) Systems
www.bca.gov.sgpreventive maintenance works, and various incentives to promote solar PV systems in Singapore. We have also refreshed the presentation of the handbook to make it more accessible and reader- friendly, as well as to incorporate examples of completed solar PV installations in …
Related documents
European structural steel standard EN 10025 : 2004
pooladan.comEN 10025 : part 2 : 2004 Non-alloy structural steels Grades, properties and nearest equivalents The tables below show the grades, properties and nearest equivalent grades from earlier standards. The grade designations are explained on the previous pages.
Product Bulletin High Alloy Stainless Steels September ...
www.emerson.comerosion. Because it has a slightly lower alloy content, its corrosion resistance is not as good as the superduplex SST. ASME SA995 grade CD3MN or 4A is the cast equivalent of S31803. Grade F51 per ASME SA182 is the forged equivalent. ASME SA240 S31803 is the plate equivalent. Only the wrought form of S31803 is approved for use
IS 2062 (2011): Hot Rolled Medium and High Tensile ...
law.resource.orgcarbon-manganese and high strength low alloy (HSLA) of structural steels. In this revision, the following changes have been made: a) Title has been modified and the word ‘low’ has been deleted, keeping in view the grades of steel contained in the standard. Requirements of low tensile structural steel are covered in IS 15911 : 2010
DESIGN GUIDELINES FOR THE SELECTION AND USE OF …
nickelinstitute.orgstainless) is the most widely used alloy of the austenitic group. It has a nominal composition of 18% chromium and 8% nickel. Table 1 AUSTENITIC STAINLESS STEELS TYPE Equivalent UNS TYPE Equivalent UNS 201 S20100 310 S31000 202 S20200 310S S31008 205 S20500 314 S31400 301 S30100 316 S31600 302 S30200 316L S31603 302B S30215 316F S31620
(UNS N08367)
www.atimetals.comN08367, but the AL-6XN PLUS alloy contains a greater concentr ation of the alloying elements (Cr, Mo, and N) which promote corrosion resistance. This is re- flected in the Pitting Resistance Equivalent (PREN = 1.0 x %Cr + 3.3 x %Mo + 30 x %N), as shown in Table 1. AL-6XN PLUS alloy is custom - melted on an as
IS 1367-3 (2002): Technical Supply Conditions for Threaded ...
law.resource.orgISO 898-7:1992, Mechanical propetiies of fasteners made of carbon steel and alloy steel – Part 7: Torsional test and minimum torques for bo/ts and screws with nomina/ diameters 1 mm to 10 mm. ISO 965-1:1998, ISO general purpose metric screw threads – Tolerances – …
STAINLESS STEEL Grade 316, 316L
store.buymetal.comSTAINLESS STEEL Grade 316, 316L Critical pitting temperatures (CPT) for 304, 316 and 2.205 at varying concentrations of sodium chloride (potentio-static determination at + 300 mV SCE SCE). pH=6.0. Pitting- resistance equivalent numbers (PREN) are a theoretical way of comparing the pitting corrosion resistance of various types of