SPECIFICATION GALVANIZING REPAIR COATING - Mobile Paint

1 BOX 717 THEODORE, ALABAMA 36590 -0717 PHONE (251) 443-6110 FAX (251) 408-0410 PRODUCT DATAPRODUCTDESCRIPTIONTYPICAL USESPRODUCTADVANTAGES80166 PHYSICALCONSTANTSGLOSSCOLORSAPPLICATIONS HIPPING &STORAGESPECIFICATIONGALVANIZING REPAIR COATINGDOD-P-21035A80166 Modified Synthetic RubberA fast drying COATING with a high zinc dust content. Meets the requirements ofMilitary SPECIFICATION REPAIR of damaged areas of galvanized metal such as weld seams and REPAIR COATING is formulated to provide a protective zinc COATING todamaged areas of galvanized metal surfaces.

2 Provides excellent protection towelded or abraded areas where the protective GALVANIZING has been removed fromthe metal surface. Meets the requirements of Military SPECIFICATION onlyMatteNonvolatile-By weight - + volume - + (Calculated) - grams/literFlash Point-100 F (Setaflash)Weight per + Film Thickness - mils dry, mils wetTheoretical Coverage @ mils dry - 247 sq. - Brush or conventional or airless - Tec Thinner 75-11 or Xylene 75-15 Dry time @ 75 F -To touch -2 hours hard -8 hours recoat -8 hoursConsists of -1 Gallon Unit5 Gallon Unit Base1 Gallon (SF)5 Gallon (SF) Zinc Dust1 Quart (SF)1 Gallon (SF)Unit Shipping Weight 19 lbs.

3 91 lbs.(SF) - Short filledShelf Life - 6 months minimum from date of manufacture when maintained inprotected storage @ 40-100 F (subject to reinspection thereafter).LIMITED WARRANTYThe successful performance of this product is highly dependent on many factors beyond our control. Results are highly dependent upon the skill of the operator. This product ismanufactured to meet the highest level of consistency and quality for the intended use. Mobile Paint warrants that its products meet the specifications which it sets for them. Shouldthis product be proven to be off- SPECIFICATION within one year from date of shipment, Mobile Paint will, at its sole discretion, either replace the product or issue credit for the originalpurchase price of the product.

4 The replacement or refund shall be the buyer s sole remedy and Mobile Paint and its affiliates MAKE NO OTHER WARRANTY OR GUARANTEE,EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY, DESIGN COMPATIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. LABOR OR COST OF LABOR ANDOTHER INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES ARE SPECIFICALLY EXCLUDED. The technical data contained herein are true and accurate to the best of ourknowledge. Published technical data and instructions are subject to change without prior your Mobile Paint Representative for the protec-tive COATING system best suited for your : Apply in good weather when air andsurface temperature are above 50 F and the surfacetemperature must be at least 5 F above the dew optimum application properties, material should bebetween 70 to 100 F prior to mixing and unmixed material in closed containers in pro-tected storage at 40-100 Preparation: Good surface preparation isessential to a satisfactory COATING system.

5 Surfaces tobe coated should be clean and dry. Remove all oil,grease, mildew of other contamination by solvent ordetergent cleaning or other effective means. Galva-nized Steel - For application to abraded or damagedareas on galvanized metal. Sandblasting (see below) isrecommended for best performance. If blasting is notfeasible, clean and abrade surface by Hand or PowerTool Cleaning (SSPC-SP2 or SP3). Steel - Althoughthis product is designed primarily as a primer for abradedor damaged areas on galvanized metal, it may be usedas a touch up primer on bare steel.

6 For best results,apply only to abrasive blasted steel. For best perfor-mance Near White Blast Cleaning SSPC-SP10 isrecommended as proper preparation. Commercial BlastCleaning SSPC-SP6 is acceptable for less severe ex-posures. Proper blast media and blasting equipmentshall be used to produce an average profile depth of minimum. Do not reuse sand abrasive media. Shotabrasives must be thoroughly clean of contaminationbefore reuse. Remove blasting dust and grit from sur-faces before painting. Blasted surfaces should be coatedwithin 8 hours after blasting or before rusting or othercontamination of the surface : This is a single component COATING .

7 (1) Mixthoroughly with a power agitator to a uniform consis-tency before use. (2) Agitate at slow speed during useto keep zinc dust in suspension. (3) Keep system tightlyclosed and free from : This product is supplied at normal sprayingviscosity. If thinning is necessary thin with up to 1/2 pint75-11 Tec Thinner or 75-15 : Apply by conventional or airless is acceptable for touch up. Keep thematerial pressure pot at or near the level of the material hoses as short as possible (25 feet maxi-mum recommended). Apply at mils wet film thicknesswhich will yield mils dry film : Brush - Use a good quality bristle spray - For pressure feed, use DeVilbissMBC gun with E tip and needle and 704 air cap orequivalent at 40-45 psi atomizing pressure and 10-15 psifluid pressure, 3/8" ID material hose, double regulatedpressure tank with oil and moisture separator.

8 Airlessspray - Minimum of 30:1 ratio pump, .023" " orificetip, 3/8" ID material hose. Special packings may benecessary due to the abrasive nature of the zinc dust inthis : During lunch, breaks or any period of workstoppage, material should be removed from hoses. Re-lease pressure from equipment and flush hoses andequipment with Tec Thinner 75-11 or Xylene 75-15. Donot repressurize equipment until ready to resume : Clean all equipment immediately after usewith Tec Thinner 75-11 or Xylene 75-15. Completelyflush all spray equipment with either of these flushing of spray equipment during the courseof the working day helps prevent buildup and : Recoat time will vary according to curingconditions.

9 Allow a minimum of 8 hours at 75 F and 50%relative humidity before applying any topcoats. Manytopcoats will require that a mist coat be applied prior toapplication of a full coat so that bubbling is : Safe storage, handling and use dictate thatadequate health and safety precautions be observedwith this product and any recommended thinners. Useris specifically directed to consult the current MaterialSafety Data Sheet for this product as well as precautionscontained on product : The technical data contained herein are trueand accurate to the best of our knowledge.

10 All productsare offered and sold subject to Mobile Paint Manufactur-ing Company s Standard Conditions of Sale. Publishedtechnical data and instructions are subject to changewithout prior notice. 80166(7/99)APPLICATION INSTRUCTIONS